Honeywell Fire-Lite Alarms ES-200X Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Control Panel
  5. Fire-Lite Alarms ES-200X
  6. Manual

Honeywell Fire-Lite Alarms ES-200X Manual

Addressable fire alarm control panel
Hide thumbs Also See for Fire-Lite Alarms ES-200X:
Table of Contents

Advertisement

Quick Links

Download this manual
Addressable Fire Alarm Control Panel
ES-200X
ES-200XC
Manual
Document LS10131-000FL-E Rev: C
7/25/2018 ECN:18-323

Advertisement

Table of Contents
loading

Related Manuals for Honeywell Fire-Lite Alarms ES-200X

Summary of Contents for Honeywell Fire-Lite Alarms ES-200X

  • Page 1 Addressable Fire Alarm Control Panel ES-200X ES-200XC Manual Document LS10131-000FL-E Rev: C 7/25/2018 ECN:18-323...
  • Page 2 Fire Alarm & Emergency Communication System Limitations While a life safety system may lower insurance rates, it is not a substitute for life and property insurance! An automatic fire alarm system—typically made up of smoke Heat detectors do not sense particles of combustion and alarm detectors, heat detectors, manual pull stations, audible warning only when heat on their sensors increases at a predetermined rate devices, and a fire alarm control panel (FACP) with remote notifica-...
  • Page 3 LiteSpeed™ and Lite-Connect™ are trademarks; and Fire-Lite® Alarms, Honeywell®, and SWIFT® are registered trademarks of Honeywell International Inc. Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. Chrome™ and Google™ are trademarks of Google Inc. Firefox® is a registered trademark of The Mozilla Foundation.
  • Page 4 • Your suggestion for how to correct/improve documentation Send email messages to: FireSystems.TechPubs@honeywell.com Please note this email address is for documentation feedback only. If you have any technical issues, please contact Technical Services. ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...

  • Page 5: Table Of Contents

    Table of Contents Section 1: Product Description ............................13 1.1: Features and Options .......................................13 1.2: Specifications........................................14 1.3: Controls and Indicators....................................16 1.4: Components ........................................16 1.4.1: Intelligent Addressable Detectors.................................17 1.4.2: Intelligent Addressable Modules ................................17 1.4.3: Addressable Device Accessories ................................17 End-of-Line Resistor Assembly................................17 Power Supervision Relay..................................17 EOL-C(R/W) Mounting Plate.................................17 1.5: Optional Modules ......................................17...
  • Page 6 Table of Contents ANN-BUS Wiring ....................................33 ANN-BUS Device Addressing ................................36 ANN-80 Remote Fire Annunciator.................................36 ANN-100 Remote Fire Annunciator...............................38 ANN-S/PG Serial/Parallel Interface Module............................39 ANN-I/O LED Driver Module ................................41 ANN-LED Annunciator Module ................................43 ANN-RLY Annunciator Module ................................45 2.8.5: Printer ........................................46 Printer Configuration ....................................46 2.8.6: ECC-FFT Firefighter Telephone ................................47 2.8.7: W-GATE Wireless Gateway ................................47 2.9: Automatic Audio Panel Control..................................47...
  • Page 7 Table of Contents Primary and Secondary Communication Paths ............................84 Trouble Report Limit (Dialer Runaway Prevention) ..........................86 Report Style ......................................87 Event Codes ......................................87 3.6.8: Annunciators......................................90 ANN-BUS Setup....................................90 ANN-BUS Options ....................................97 3.6.9: Password Change....................................99 Invalid Password.....................................99 3.6.10: Clear Program....................................100 3.6.11: Program Check ....................................100 3.7: Maintenance Programming Level..................................101 3.7.1: Disable Point.......................................101 3.7.2: History ........................................102...
  • Page 8 Table of Contents 4.24.8: History ......................................117 4.24.9: Annunciators.....................................117 4.24.10: Communicator ....................................117 4.24.11: Print.........................................118 Chamber Value .....................................119 Drift Compensation....................................119 Maintenance Alert....................................119 4.24.12: Time-Date .......................................120 4.24.13: Battery Charger....................................120 4.24.14: 4XTM Supervision ..................................120 4.24.15: Remote Sync....................................120 Section 5: Central Station Communications - POTS Transmission ................. 121 5.1: Transmittal Priorities .....................................121 Section 6: FS-Tools Upload/Download........................
  • Page 9 Table of Contents Appendix G: Central Station Points..........................152 Appendix H: NFPA Requirements..........................154 Appendix I: Open/Short/Ground Trip Values ......................155 Appendix J: Canadian Applications ..........................156 Index ....................................159 Slide-in Labels ................................163 ES-200X and ES-200XC Fire Alarm Control Panels Operating Instructions ............165 ES-200X Series Manual —...
  • Page 10 It is imperative that the installer understand the requirements of the Authority Having Jurisdiction (AHJ) and be familiar with the stan- dards set forth by the following regulatory agencies: • Underwriters Laboratories/Underwriters Laboratories Canada • National Fire Protection Association Before proceeding, the installer should be familiar with the following documents. NFPA Standards NFPA 72 National Fire Alarm Code NFPA 70 National Electrical Code...
  • Page 11 250V ES50- PCA REV ES200- PCA REV ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...
  • Page 12 Peripheral Devices and Their Documents: ANN Audio Control for ECC-50/100 Doc. #LS10001-000FL-E ANN-RLY ANN-S/PG ANN-100 ANN-I/O Relay Card ANN-80 Printer Driver LCD Text Annunciator ANN-(R)LED LED Driver Doc. #53033 LCD Text Annunciator Doc. #151417 Doc. #LS10205-000FL-E LED Display Doc. #151416 Doc.

  • Page 13: Section 1: Product Description

    Section 1: Product Description The Fire-Lite ES-200X is an addressable FACP (Fire Alarm Control Panel) with a pre-installed communicator card that is compact, cost effective, intelligent, and has an extensive list of powerful features.The combination of Fire-Lite’s newer series devices and legacy 300 Series devices, along with the ES-200X FACP, offer the latest in fire protection technology.

  • Page 14: Specifications

    Product Description Specifications • Optional FS-Tools programming utility for local or remote Upload/Download of programming and data (available for download from www.firelite.com) • Compatible with Fire-Lite’s devices in LiteSpeed and CLIP mode (refer to SLC Wiring Manual for a list of compatible addressable devices) •...
  • Page 15 Specifications Product Description Resettable or Nonresettable Special Application Power (24 VDC Nominal) - TB11, Terminals 5 (+) & 6 (-) Factory-set as resettable, suitable for powering four-wire smoke detectors Class B wiring only Maximum ripple voltage: 20 mV Total DC current available is up to 1.0 amp (see Figure 1.1) Power-limited circuit Refer to the Device Compatibility Document for listed compatible devices Note: Refer to the programming section to configure power as resettable/non-resettable.

  • Page 16: Controls And Indicators

    Product Description Controls and Indicators 1.3 Controls and Indicators LCD Display The FACP uses an 80-character (4 lines X 20 characters) high viewing angle LCD display. The display includes a long life LED backlight that remains illuminated. If AC power is lost and the system is not in alarm, SYSTEM NORMAL the LED backlight will turn off to conserve batteries.

  • Page 17: 1: Intelligent Addressable Detectors

    Optional Modules Product Description ® • Dialing the Central Station(s) number: default is Touch-Tone , programmable to rotary • For tone burst or touchtone type formats: discern proper Ack and Kissoff tone(s). The frequency and time duration of the tone(s) varies with the transmission format.

  • Page 18: Accessories

    Product Description Accessories 4XTMF Transmitter Module The 4XTMF provides a supervised output for local energy municipal box transmitter, alarm and trouble reverse polarity. It includes a disable switch and disable trouble LED. A jumper on the module is used to select an option which allows the reverse polarity circuit to open with a system trouble condition if no alarm condition exists.

  • Page 19: Chg-120F Battery Charger

    Accessories Product Description CHG-120F Battery Charger The CHG-120F is capable of charging up to 120 AH lead-acid batteries with the ES-200X FACP. The FACP battery charger must be dis- abled, by removing jumper JP5, when using the CHG-120F. The batteries and charger can be housed in the BB-55F battery box which can be mounted up to 20 feet away from the control panel.

  • Page 20: Ann-I/O Led Driver Module

    Before connecting the control panel to the public switched telephone network, the installation of two RJ31X jacks is necessary. If trouble is experienced with this equipment, for repair or warranty information, please contact: Manufacturer: Honeywell International, Inc. One Fire-Lite Place Northford, CT 06472...

  • Page 21: 2: Telephone Company Rights And Warnings

    Telephone Requirements and Warnings Product Description 1.8.2 Telephone Company Rights and Warnings The telephone company, under certain circumstances, may temporarily discontinue services and/or make changes in its facilities, ser- vices, equipment or procedures which may affect the operation of this control panel. However, the telephone company is required to give advance notice of such changes or interruptions.

  • Page 22: Section 2: Installation

    Section 2: Installation The cabinet may be either semi-flush or surface mounted. The cabinet mounts using two key slots and two 0.250” (6.35 mm) diameter holes located in the backbox. The key slots are located at the top of the backbox and the two securing holes at the bottom. Carefully unpack the system and check for shipping damage.
  • Page 23 Mounting the Backbox Installation Semi-Flush Mounting Do not recess box more Hinge Slot for optional than 3.875” into wall to Dress Panel avoid covering venting holes on top of box. Mounting slots for optional Trim Ring Semi-flush mounting hole Hinge Slot for optional Dress Panel Figure 2.2 ES-200X Cabinet Mounting ES-200X Series Manual —...
  • Page 24 Installation Mounting the Backbox 5.207” (13.23cm) 16.822” (42.73 cm) 6.537” (16.6cm) Width Depth Height 19.26” (48.92 cm) Right Side Left Side Bottom Figure 2.3 Cabinet Dimensions An optional Trim Ring (P/N TR-CE-) is also available for semi-flush mount installations. ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...

  • Page 25: Power

    Power Installation 2.2 Power WARNING: RISK OF EQUIPMENT DAMAGE AND PERSONAL INJURY SEVERAL DIFFERENT SOURCES OF POWER CAN BE CONNECTED TO THIS PANEL. DISCONNECT ALL SOURCES OF POWER BEFORE SERVICING. THE PANEL AND ASSOCIATED EQUIPMENT MAY BE DAMAGED BY REMOVING AND/OR INSERTING CARDS, MODULES OR INTERCONNECTING CABLES WHILE THIS UNIT IS ENERGIZED.

  • Page 26: 3: Special Application Dc Power Output Connection

    Installation Relays 2.2.3 Special Application DC Power Output Connection All Special Application DC power outputs are power-limited (refer to “UL Power-limited Wiring Requirements” on page 29). Power-limited Resettable or Non-resettable Power Power-limited Non-resettable or Resettable Power 1.0 amperes max., 24 VDC nominal filtered, programmable 1.0 amperes max., 24 VDC nominal filtered, non- resettable or non-resettable power can be drawn from TB11 resettable or resettable power is programmable.

  • Page 27: 1: Class B Nac Wiring

    Notification Appliance Circuits Installation 2.4.1 Class B NAC Wiring 4 Class B Notification Appliance Circuits, supervised and power-limited - 4.7 kΩ, ½ watt P/N:71252 UL listed NAC 3 NAC 1 NAC 4 NAC 2 Polarized Bells Polarized Bells Polarized Strobes Polarized Strobes Polarized Horns Polarized Horns...

  • Page 28: Remote Synchronization Output

    Installation Remote Synchronization Output 2.5 Remote Synchronization Output Synchronization is a feature that controls the activation of notification appliances in such a way that all devices will turn on and off at exactly the same time. This is particularly critical when activating strobes which must be synchronized to avoid random activation and a potential hazard to individuals.

  • Page 29: Ul Power-Limited Wiring Requirements

    UL Power-limited Wiring Requirements Installation 2.6 UL Power-limited Wiring Requirements Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” (6.35 mm) away from any nonpower-limited circuit wiring and nonpower-limited circuit wiring must enter and exit the cabi- net through different knockouts and/or conduits.

  • Page 30: Ipots-Com Communicator

    There are two configurable dip switches on the IPOTS-COM communicator. Switches • SW2: 6-position dip switch- FUTURE USE- No configuration necessary. • SW3: 2-position dip switch- Factory Settings- Do not change unless instructed to do so by Honeywell. ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...

  • Page 31: Optional Module Installation

    Optional Module Installation Installation 2.8 Optional Module Installation WARNING: RISK OF ELECTRIC SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING. 2.8.1 CELL-CAB-FL/CELL-MOD The CELL-CAB-FL/CELL-MOD offers an optional GSM communicator card for central station reporting. It mounts in its own plastic or metal enclosure.
  • Page 32 Installation Optional Module Installation Before installing the module, place the disconnect switch to the right (disconnect) position to prevent accidental activation of the munic- ipal box. Note that a Disconnect LED will illuminate after the module is installed in the ES-200X. In addition, the System Trouble LED will turn on to indicate the Disconnect condition.

  • Page 33: 4: Ann-Bus Annunciators/Modules

    Optional Module Installation Installation Standoff ALRM TRBL SUPV RMT SYNC NAC1 OUT+ RTN+ RTN- OUT- J12 & J13 Connectors Jumper JS3 Standoff 4XTMF FACP main circuit board Figure 2.16 4XTMF Connectors to ES-200X Connectors NOTE: When a 4XTMF is installed, enable supervision in panel programming. Jumper JS3 on the FACP main circuit board can be used to configure the FACP supervisory relay for operation with the 4XTMF module.
  • Page 34 Installation Optional Module Installation In general, the wire length is limited by resistance, but for heavier wire gauges, capacitance is the limiting factor. Maximum length can never be more than 6,000 feet (1,800 m), regardless of gauge used. The following formulas were used to generate the wire distances: 2.0 Volts Maximum Resistance (Ohms) Total Worst Case Current Draw (amps)
  • Page 35 Optional Module Installation Installation Figure 2.18 illustrates the wiring between the FACP’s Secondary ANN-BUS and ANN-BUS devices. ANN-BUS and power wiring are supervised and power-limited 4 3 2 1 ANN-BUS Device Secondary 24 VDC ANN-BUS nonresettable ES-200X Figure 2.18 Secondary ANN-BUS wiring to ANN-BUS Device ...

  • Page 36: Ann-Bus Device Addressing

    Installation Optional Module Installation ANN-BUS Device Addressing Each ANN-BUS device requires a unique address (ID Number) in order to communicate with the FACP. A 5-position DIP switch on each device is used to set this address. The address set for these devices must also be programmed at the FACP for the specific device (refer to the programming section titled “ANN-BUS Setup”...
  • Page 37 Optional Module Installation Installation  Mounting The ANN-80 can be surface or semi-flush mounted to a single, double or 4” square electrical box. Select and remove the appropriate knockout(s), pull the necessary wires through the knockouts and mount the annunciator in or on the wall depending on the type of instal- lation desired.

  • Page 38: Remote Fire Annunciator

    Installation Optional Module Installation After all connections are made, remove extra wire from inside of annunciator by dressing it neatly through wire channel, with any excess wire pushed back through hole into electrical box ANN-BUS and power wiring are supervised and power-limited 4 3 2 1 ANN-BUS Device Primary...

  • Page 39: Ann-S/Pg Serial/Parallel Interface Module

    Optional Module Installation Installation  Programming Following installation and wiring of the ANN-100 LCD annunciator to the FACP, the annunciator must be added to the system via FACP programming. Refer to the programming section titled “ANN-BUS Setup” on page 90 in this manual for detailed programming informa- tion.
  • Page 40 Installation Optional Module Installation  Setting Printer Options Refer to the documentation supplied with the PRN-7 printer for instructions on using the printer menu controls. Set the printer options (under the menu area) as shown in the following table: Option Setting Option Setting...

  • Page 41: Ann-I/O Led Driver Module

    Optional Module Installation Installation ANN-I/O LED Driver Module  ANN-I/O Board Layout Figure 2.22 illustrates the ANN-I/O board showing locations of screw terminals for connection to the FACP, pin connectors for connect- ing LEDs and the DIP switch for selecting the ANN-BUS ID number. LED Out LED Out LED Out...
  • Page 42 Installation Optional Module Installation  ANN-I/O Connection to FACP The ANN-I/O connects to the FACP via the ANN-BUS as illustrated in Figure 2.23. After the ANN-I/O is connected to the panel, it must be added to the system via FACP programming. Refer to the section titled “ANN-I/O Options” on page 91. 20 21 LED Out LED Out...

  • Page 43: Ann-Led Annunciator Module

    Optional Module Installation Installation Pin # LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Cathode LED9 LEDs LED10 LED Power Anode no connection Pin # LED11 LED12 LED13 LED14 LED15 LED16 LED17 LED18 Cathode LED19 LEDs LED20 Anode LED Power no connection Figure 2.24 ANN-I/O LED Wiring ANN-LED Annunciator Module...
  • Page 44 Installation Optional Module Installation  Specifications • Max. ANN-BUS Voltage: 24 VDC • Max. Current:  Alarm: 68 mA  Standby: 28 mA • Operating Temperature: 32°F to 120°F (0°C to 49°C) • For indoor use in a dry location only ...

  • Page 45: Ann-Rly Annunciator Module

    Optional Module Installation Installation ANN-RLY Annunciator Module  Specifications • Operating Voltage: 24 VDC • Max. Current:  Alarm: 75 mA  Standby: 15 mA • Operating Temperature: 32°F to 120°F (0°C to 49°C) • For indoor use in a dry location only ...

  • Page 46: 5: Printer

    Installation Optional Module Installation  ANN-RLY Board Layout and Connection to FACP Figure 2.29 illustrates the ANN-RLY board showing locations of screw terminals for connection to the FACP and the DIP switches for selecting the ANN-BUS ID number. ANN-BUS (ID#) Address DIP switch 1 2 3 4 5 6 7 8 ANN-BUS and power wiring are...

  • Page 47: 6: Ecc-Fft Firefighter Telephone

    Automatic Audio Panel Control Installation 2.8.6 ECC-FFT Firefighter Telephone The ECC-FFT connects from TB11 (non-resettable aux power) on the FACP to the DC Power input on the ECC-FFT board. ECC-FFT ES-200X Figure 2.30 ECC-FFT Connections 2.8.7 W-GATE Wireless Gateway The W-GATE connects to the FACP’s SLC connection at TB10. The W-GATE can be powered by either the SLC or an external 24 VDC power source.
  • Page 48 Installation Automatic Audio Panel Control (1 of 5 using the legacy ACC panel) can be generated over the selected speaker circuit. Any fault in the ECC-50/100 audio system is sent to the FACP via the FACP Data Bus and is indicated as an annunciator fault on the FACP display. A fault at the ACC-25/50ZS Series panel will cause the FACP to indicate a System Trouble and the display will indicate a Voice Evac Fault.

  • Page 49: Section 3: Programming

    Section 3: Programming NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION AND OTHER INVOLVED PARTIES This product incorporates field-programmable software. In order for the product to comply with the requirements in the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864, certain programming features or options must be limited to specific values or not used at all as indicated below: Permitted in Program feature or...

  • Page 50: User Programming

    Programming User Programming Last Event Clear Delete RECALL Insert A - Z A - Z 0 - 9 0 - 9 ■ (on YZ key) Space bar — — • •         ENTER Enter ACK/STEP SILENCE...

  • Page 51: Initial Power-Up

    Initial Power-up Programming Pressing 1, while this screen is being displayed, will cause the control panel to enter the Read Status Mode which allows the user to view the programmed features and status of the control panel The Read Status feature is not password protected. Refer to “Read Status” on page 114 for a detailed description of this feature.

  • Page 52: Master Programming Level

    Programming Master Programming Level To access user Programming mode, press the Enter or Mode key. The LCD will display the following. 1=READ STATUS MODE 2=PROGRAMMING MODE 3=FS-TOOL UP/DOWNLD 4=USB UP/DOWNLOAD To enter the user Programming mode, press 2. The display will read as follows: PROGRAMMING ENTER PASSWORD ...

  • Page 53: 2=Point Program

    Master Programming Level Programming When Autoprogramming is completed, the control panel will display the type and quantity of each device installed on the SLC loop sim- ilar to the following display: # OF DET LOOP1 055 # OF MON LOOP1 035 # OF CON LOOP1 030 Autoprogram Result Screen #1 In the preceding example, the display indicates that the SLC Loop has 55 addressable detectors, 35 monitor modules and 30 control...
  • Page 54 Programming Master Programming Level NOTE: The system must be monitored by a Supervising Station when using carbon monoxide detection per The Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 720. The programmer can continue adding detectors by pressing the ESC key which will return the display to the Add Detector Screen. ...
  • Page 55 Master Programming Level Programming  Normal - indicates that the detector with the selected address is physically installed on the SLC and communicating with the control panel (enabled)  <ADJ><NOUN> - represents the adjective and noun, which have been programmed, describing the location of the displayed device ...
  • Page 56 Programming Master Programming Level Fire/CO response is programmable (Alarm, Supv, or None) User-Defined-12 same as previous (Fire/CO) While viewing either Detector Type screen, select the type of detector being programmed by pressing the corresponding keyboard num- ber key. The display will return to Edit Detector Screen #2 and indicate the selection next to the Type option. NOTE: If a detector is selected to be a DUCT SUPERV type, it will function like a supervisory point not a fire alarm point.
  • Page 57 Master Programming Level Programming  Enable zones Z001 and Special Purpose Zone Pre-signal 98 and set the Pre-signal delay timer to some value With the preceding program settings, when the detector with address 005 is activated, zone Z98 will cause its associated control module to activate immediately, sounding the connected signaling device to indicate the Pre-signal condition.
  • Page 58 Programming Master Programming Level The sounder base volume has two settings: Low or High. Press 1 while viewing Sounder Base Screen #2 SOUNDER BASE 1=ZONE ASSIGNMENT until the display reads Low or High as desired. Each press of the 1 key will cause the display to toggle 000 000 000 000 000 between Volume Low and Volume High.
  • Page 59 Master Programming Level Programming Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. 1=STANDARD ADJECTIVE 2=STANDARD NOUN Note that the keyboard down arrow key must be pressed to see all the Noun screens. Press the number corre- 3=CUSTOM ADJECTIVE sponding to the noun that is to be used as a descriptor for the location of the detector currently being pro- 4=CUSTOM NOUN...

  • Page 60: Module Programming

    Programming Master Programming Level Module Programming Pressing 2, while viewing Point Program Screen #2, will allow the programmer to add, delete or change the POINT PROGRAM SELECT TYPE programming of an addressable module. The following screen will be displayed by the control panel: 1=DETECTOR 2=MODULE MODULES...
  • Page 61 Master Programming Level Programming A flashing cursor will appear in the position of the first asterisk to the left. The programmer keys in the three digit module address, such as 012. When the last digit is keyed-in, if the selected address has not been added to programming, a screen showing information about a device that is installed with a lower address, closest to the selected address, will be displayed.
  • Page 62 Programming Master Programming Level Type Monitor Using the FS-Tools Upload/Download utility, unique user-defined monitor types can be created and loaded EDIT MONITOR 1=ENABLED into the FACP for later use. The FACP response to the activation of a user-defined type is the same as most 2=TYPE MONITOR previous standard types in the list, thus allowing a variety of user-defined types and responses.
  • Page 63 Master Programming Level Programming Ack Switch Acts like panel Acknowledge Key Sil Switch Acts like panel Silence Key Reset Switch Acts like panel Reset Key Drill Switch Acts like panel Drill Key PAS Bypass PAS Disable HVAC RESTART Switch (see note 2) Drill Switch AR Acts like panel Drill Key, nonlatching (tracking) Wireless Gateway...
  • Page 64 Programming Master Programming Level Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. 1=STANDARD ADJECTIVE 2=STANDARD NOUN Note that the keyboard down arrow key must be pressed to see all the Adjective screens. Press the number 3=CUSTOM ADJECTIVE corresponding to the adjective that is to be used as a descriptor for the location of the monitor module cur- 4=CUSTOM NOUN...
  • Page 65 Master Programming Level Programming As an example, the user could quickly enter ‘FLR_3_ROOM 305’ as follows: The cursor is on the first letter of the Adjective field. Press the zero key twice to display FLR_3 With the cursor on the first letter of the Noun field, press the zero key twice to recall the display ROOM_304. The cursor automatically jumps from the first to the last letter of the Noun field With the cursor on the last letter of the Noun field, press the zero key again to increment the room number to 305 Press the right arrow key to advance the zone field...
  • Page 66 Programming Master Programming Level While viewing one of the Control Type screens, select the type of control module being programmed by pressing the corresponding key- pad number key. The display will return to the Edit Control Screen #2 and indicate the new type selection. NOTE: A control relay module set to the Resettable Power type will follow the main circuit board 24 VDC resettable power unless the control relay module is disabled.
  • Page 67 Master Programming Level Programming Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. 1=STANDARD ADJECTIVE 2=STANDARD NOUN Note that the keyboard down arrow key must be pressed to see all the Adjective screens. Press the number 3=CUSTOM ADJECTIVE corresponding to the adjective that is to be used as a descriptor for the location of the control module cur- 4=CUSTOM NOUN...

  • Page 68: 3=Zone Setup

    Programming Master Programming Level • The above increment function may be repeated with each press of the zero key. As an example, the user could quickly enter ‘FLR_3_ROOM 305’ as follows: The cursor is on the first letter of the Adjective field. Press the zero key twice to display F.LR_3 With the cursor on the first letter of the Noun field, press the zero key twice to recall the display ROOM_304.

  • Page 69: Special Purpose Zone

    Master Programming Level Programming Special Purpose Zone Pressing 3 for Special Purpose, while viewing Zone Setup Screen #1, will display the following screens: SPECIAL PURPOSE SPECIAL PURPOSE 1=PAS 97 1=LOCAL ALM 96 2=PRESIGNAL 98 3=TWO STAGE 99 Special Purpose Zone Screen #1 Special Purpose Zone Screen #2 Zones 097, 098, 099, and 096 can be programmed for normal zone operation or for special purpose applications.

  • Page 70: Zone Type

    Programming Master Programming Level This display will show all of the zones that are disabled in the control panel. Note that an up and/or down arrow may appear in the upper right corner of the display, indicating that additional screens of zone information exists. Press the up or down arrow keys to view the additional zones.

  • Page 71: 4: Loop Setup

    Master Programming Level Programming Pressing the down arrow key will display additional screens for Zones up to Z99. Press the number key corresponding to the Zone to be programmed. Screens will be displayed allowing the programmer to select Audio Messages 1 through 14. When an audio message is selected, the display will return to the Zone Message screen, showing the message selected for that particular zone.

  • Page 72: Function Keys

    Programming Master Programming Level • Language: This option allows the user to switch between English and French language text on the panel display. • Charger Enable: This option allows the user to install an external battery charger. • 4XTM Supervision: This feature enables supervision of an installed 4XTMF Transmitter Module. •...

  • Page 73: Banner

    Master Programming Level Programming Banner The top line of the display, which appears when the control panel is in normal mode, can be changed by SYSTEM SETUP 1=FUNCTION KEYS using the Banner option. Pressing 2 while viewing System Setup Screen #1 will cause the following to be 2=BANNER displayed: 3=TIME-DATE...

  • Page 74: Timers

    Programming Master Programming Level  Date To change the date, press 2 while viewing the Time-Date Screen. The following screen will be displayed: ENTER DATE MONTH DAY YEAR 05-04-17 Date Screen A flashing cursor is located toward the top left of the display. Below the cursor is the current date. To change the date, enter the two-digit month followed by the two-digit day and then the two-digit year (17 for 2017, 18 for 2018, etc.).
  • Page 75 Master Programming Level Programming  Pre-signal Delay The factory default setting for Pre-signal delay is 000 for no delay. To select a Pre-signal delay of 001 to 180 seconds for all devices pro- grammed for Pre-signal, press 2 while viewing Timer Screen #1. The following screen will be displayed: PRESIGNAL DELAY RANGE 0-180 SECONDS ...

  • Page 76: Nac (Notification Appliance Circuit)

    Programming Master Programming Level A flashing cursor will appear in the lower left corner of the display. Type the three digit control module delay in seconds (000 to 180 sec- ond delay). When the third digit is entered, the display will return to the Delay Screen which will indicate the new delay time. Refer to the table on page 49 for permissible settings.
  • Page 77 Master Programming Level Programming  Auto Silence The Auto Silence feature, when enabled, automatically silences all main circuit board silenceable notifica- NAC # tion appliances after a programmed length of time. To enable this feature and program the time delay before 1=AUTO SILENCE 2=CODING TEMPORAL...

  • Page 78: Relays

    Programming Master Programming Level  Zone A maximum of five zones can be programmed to each main circuit board NAC. Pressing 1 while viewing NAC # 1=ZONE ASSIGNMENT NAC Screen #3 displays the following screen: 000 2=SILENC INHIBIT NO ZONE ASSIGNMENT NAC Screen #3 Z000 ...

  • Page 79: Canadian Option

    Master Programming Level Programming To program Relay 1 or Relay 3, press the number corresponding to the selected relay. Note that Relay 2 is fixed as a Trouble relay. Selecting Relay 2 will have no effect on its programming. The following screen will appear for each relay to be programmed: RELAY # 1=TYPE ALARM...

  • Page 80: Mns Override

    Programming Master Programming Level MNS Override Pressing 3 while viewing System Setup Screen #3 will allow the programmer to configure the system for SYSTEM SETUP use with the Mass Notification System (ECC-50/100 panel). Each press of the 3 key will toggle the display 1=CANADIAN OPT.

  • Page 81: 6: History

    Master Programming Level Programming 3.6.6 History The History option allows an authorized user to view or erase events which have occurred in the control PROGRAMMING 1=HISTORY panel. Pressing 1 while viewing Programming Screen #3 will display the History options as shown in the 2=COMMUNICATOR following display: 3=ANNUNCIATORS...

  • Page 82: Pots Settings

    Programming Master Programming Level POTS Settings The POTS settings configure the system when telephone lines are used to contact central station. Pressing 2 COMMUNICATOR 1=INSTALLED while viewing the Communicator Screen #1 will display the following. 2=POTS SETTINGS POTS SETTINGS 3=IP SETTINGS 1=LINE 1 Communicator Screen #1 2=LINE 2...

  • Page 83: Ip Settings

    Master Programming Level Programming IP Settings The IP settings configure the system when the central station will be contacted over the internet. The fol- COMMUNICATOR 1=INSTALLED lowing screens allow the user to enter the device addresses needed for communication. Pressing 3 while 2=POTS SETTINGS viewing the Communicator Screen #1 will display the following.

  • Page 84: Primary And Secondary Communication Paths

    Programming Master Programming Level Select the number of minutes allowed, 1-60, before a fault is shown on the panel. Primary and Secondary Communication Paths The Primary and Secondary Communication Path screens are used to configure the methods (primary and COMMUNICATOR 1=PRI COMM PATH backup) for reporting to central station.
  • Page 85 Master Programming Level Programming Communication Format Pressing 1 while viewing Primary/Secondary Screen #3 will cause the following screen to be displayed: POTS XXX COMM PATH 1=COMM FORMAT COMM FORMAT ADEMCO CONTACT ID 1=ADEMCO CONTACT ID 2=SIA 8 POTS Comm Path Screen #3 3=SIA 20 The Communication Format is determined by the type of receiver that the Communicator is transmitting to.

  • Page 86: Trouble Report Limit (Dialer Runaway Prevention)

    Programming Master Programming Level Enter the City ID, Central Station ID, and Account Code all provided by the monitoring station. NOTE: When using Ethernet as the primary and Cellular as secondary, the three CS account codes must be the same for both paths. Supervision Settings Pressing 1 while viewing Ethernet Options Screen #2 will cause the display to toggle between the 4 super- ETHERNET OPTIONS...

  • Page 87: Report Style

    Master Programming Level Programming To set the Trouble Report Limit, press 3 while viewing Communicator Screen #1. The following screen will be displayed. TROUBLE CALL LIMIT 00-99 RANGE  Trouble Report Limit Screen Enter a value between 00 and 99, then press Enter to set the Report Limit to this value. Refer to the table on page 49 for permissible set- tings.
  • Page 88 Programming Master Programming Level SMOKE (ION) Zone Point DET-USER-DEF-2 Zone Point HEAT DETECT Zone Point DET-USER-DEF-3 Zone Point SMOKE DUCT-P Zone Point DET-USER-DEF-4 Zone Point PHOTO W/HEAT Zone Point DET-USER-DEF-5 Zone Point CO ALARM Zone Point DET-USER-DEF-6 Zone Point DUCT SUPERVISORY Zone Point DET-USER-DEF-7...
  • Page 89 Master Programming Level Programming MNS OVERRIDE MNS MESSAGE Message # MANUAL EVACUATION AC_FAIL DRILL SLC 1 SHORT A SLC 1 SHORT B SLC 1 OPEN A SLC 1 OPEN B SLC 1 GND FAULT POS SLC 1 GND FAULT NEG SLC 1 COMM FAULT SLC 1 OPEN FAULT SLC 1 SHORT FAULT...

  • Page 90: 8: Annunciators

    Programming Master Programming Level OFF_NORMAL_MESSAGE 24_HOUR_TEST 24 HOUR ABNORMAL TES UPDOWN REQUEST UPLOAD SUCCESS DOWNLOAD SUCCESS UPDOWN FAILURE GENERAL ALARM GENERAL SUPERVISORY Table 3.3 Event Codes (Continued) 3.6.8 Annunciators Pressing 3 while viewing Programming Screen #3 will cause the control panel to display the following PROGRAMMING 1=HISTORY screens:...
  • Page 91 Master Programming Level Programming Pressing 1 for Type will display the following screens: ANN-BUS MODULE TYPE ANN-BUS MODULE TYPE ANN-BUS MODULE TYPE 1=ANN-I/O MODULE 1=ANN-RLY MODULE 1=NOT INSTALLED 2=ANN-S/PG MODULE 2=ANN-ACC 2=ANN-80 MODULE 3=ANN-LED MODULE 2=ANN-ECC 3=ANN-100 MODULE Module Type Screen #1 Module Type Screen #2 Module Type Screen #3 Press the number corresponding to the module/device type that is installed with the selected address.
  • Page 92 Programming Master Programming Level ANN-I/O Zone Option If Zone is selected as the module option, the first ten LEDs on the first ANN-I/O module will display the system status information. The remaining 30 LEDs on the first module and 40 LEDs on the remaining modules will display the active/alarm status of each zone in the Zone Range programmed for that particular module.
  • Page 93 Master Programming Level Programming ANN-I/O Point Option If Point is selected as the module option, the first ten LEDs on the first ANN-I/O module will display the system status information. The remaining 30 LEDs on the first module and 40 LEDs on each additional module will display the active/alarm status of each point in the Point Range programmed for that particular module.
  • Page 94 Programming Master Programming Level ANN-LED Options Pressing 2 for Module Options while viewing the (XXX) ANN-BUS Address Screen when the ANN-LED ANN XXX 1=ENABLED option is selected, will display the following screen: 2=MODULES INSTALLED 3=AUTO-CONFIGURE ANN-LED - ADDR X-1 ANN-LED - ADDR X-1 ANN-LED - ADDR X-1 ANN XXX Screen #2 1=POINT/ZONE...
  • Page 95 Master Programming Level Programming ANN-LED Zone Option - Alarm, Trouble and Supervisory If Zone is selected as the module option, and the module is programmed to annunciate alarms, troubles and supervisories, the first ten LEDs on the first ANN-LED module will display the system status information. The remaining 30 LEDs on the first module and the last 30 LEDs on the remaining modules will display the alarm, trouble and supervisory status for each of the ten zones in the Zone Range programmed for that particular module.
  • Page 96 Programming Master Programming Level Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Point 031 Point 032 Point 033 Point 034 Point 035 Active/Alarm Active/Alarm Active/Alarm Active/Alarm Active/Alarm Point 036 Point 037 Point 038 Point 039...

  • Page 97: Ann-Bus Options

    Master Programming Level Programming ANN-RLY Options Pressing 2 for Module Options while viewing the ANN-BUS Address Screen when the ANN-RLY option is ANN XXX 1=ENABLED selected, will cause the following screen to be displayed: 2=MODULES INSTALLED 3=AUTO-CONFIGURE ANN-RLY - ADDR. X-1 ANN XXX Screen #2 1=RLY 1 ZONE 000...
  • Page 98 Programming Master Programming Level  ANN-S/PG (Print) Options The Print option allows the programmer to configure the optional printer. Pressing 1 while viewing the XXX ANN-BUS 1=ANN-S/PG OPTIONS ANN-BUS screen will display the following screens: 2=ANN-LED OPTIONS 3=ANN-80/100 OPTIONS ANN-S/PG OPTIONS ANN-S/PG OPTIONS ANN-S/PG OPTIONS 1=PORT...

  • Page 99: 9: Password Change

    Master Programming Level Programming The Lock Enable option allows the programmer to select whether or not any installed ANN-80 or ANN-100 annunciator must be unlocked by its key before any annunciator key presses will function. Pressing 2 while viewing the ANN-80/100 Options Screen #1 causes the display to toggle between Lock Enable Yes (annunciator must be unlocked for keys to function) and Lock Enable No (lock position is ignored).

  • Page 100: 10: Clear Program

    Programming Master Programming Level The programmer may hit the escape key and re-enter the password correctly. However, if the password has been forgotten, record the 20- character code and contact Fire•Lite Technical Services. After proper authentication, the master password will be supplied to the pro- grammer.

  • Page 101: Maintenance Programming Level

    Maintenance Programming Level Programming The Zone No Output feature allows the programmer to view the zones which have not been programmed to at least one output device (not including general alarm Zone 00). The example in the preceding screen indicates that Zones 05, 07, 09, 10 and 11 have been pro- grammed to an addressable detector with an address of 001 on loop 1 but have not been programmed to any output devices.

  • Page 102: 2=History

    Programming Maintenance Programming Level 3.7.2 History Pressing 2 while viewing Maintenance Screen #1 will cause the following screen to be displayed: PROGRAMMING 1=POINT PROGRAM HISTORY 2=HISTORY 3=PROGRAM CHECK 1=VIEW EVENTS 2=ERASE HISTORY Maintenance Screen #1 History Screen The History feature allows the operator to view control panel events which have been stored in a history file in memory and erase the contents of the history file Pressing 1 while viewing the History screen will cause the following screen to be displayed: HISTORY...

  • Page 103: 4: Walktest

    Maintenance Programming Level Programming Pressing 3 while viewing Program Check screen will cause a screen similar to the following to be displayed: ZONES NO OUTPUT 005 007 009 010 011 1D001 The Zone No Output feature allows the programmer to view the zones which have not been programmed to at least one output device (not including general alarm Zone 00).

  • Page 104: 5: System

    Programming Maintenance Programming Level 3.7.5 System Pressing 2 while viewing Maintenance Screen #2, will display the following screen: PROGRAMMING 1=WALKTEST SYSTEM SYSTEM 2=SYSTEM 1=TIME/DATE 3=ZONE SETUP 1=NACS ENAB 1,2,3,4 2=REM SYNC ENAB YES 2=CHARGER ENAB Maintenance Screen #2 3=4XTM SPV ENB System Screen #1 System Screen #2 Pressing 1 while viewing System Screen #1 will display the following:...
  • Page 105 Maintenance Programming Level Programming Pressing 1 while viewing Zone Setup screen will display the following screen: ZONE TO ENABLE Z Enable Screen A flashing cursor appears to the right of the Z. To enable a zone, enter the three digit zone number (000 - 099). After the second digit is entered, the zone will be enabled and the cursor will return to the original position.

  • Page 106: Section 4: Operating Instructions

    Section 4: Operating Instructions 4.1 Panel Control Buttons 4.1.1 Acknowledge The first press of the Acknowledge key silences the piezo sounder, changes flashing LEDs to steady, and also changes the status field on the LCD display from capital letters to small letters. When the piezo is silenced, an acknowledge message is sent to the printer and the history file.

  • Page 107: Normal Operation

    Normal Operation Operating Instructions Disabled This is a yellow LED that flashes to indicate that a zone, NAC, detector or module has been temporarily disabled in programming by the user. Maintenance This is a yellow LED that flashes to indicate that a smoke detector requires cleaning or replacement due to an invalid chamber reading or excessive drift.

  • Page 108: Alarm Operation

    Operating Instructions Alarm Operation  <NOUN>; refers to the user programmed noun descriptor from library list resident in the control panel or custom entry via PC. • Third line in display: INVREP indicates an invalid reply from the addressable device. Other possible troubles include: –...

  • Page 109: Co Alarm Operation

    CO Alarm Operation Operating Instructions • Third line in display: Z000 indicates the zone programmed to this device which, in this example, is general alarm Zone 000. Note that a single device can be programmed to five different zones but only the first zone will be displayed. •...

  • Page 110: Process Monitor Operation

    Operating Instructions Process Monitor Operation A typical Supervisory event would be displayed as illustrated in the following: ACTIVE SUPERVISORY <ADJ> <NOUN> Z000 10:00A 012116 1M001 Note that, like alarms, supervisory signals latch (except when programmed for supervisory autoresettable) and can be assigned to soft- ware zones.

  • Page 111: Mass Notification Operation

    Mass Notification Operation Operating Instructions • Timers are not started • Store event in history buffer • Activate appropriate LED on the ANN-LED annunciator (required for this application) • Each ANN-LED can support up to 10 zones. Medical alert conditions latch. They can be assigned to software zones. 4.11 Mass Notification Operation The FACP may be installed with an ECC-50/100 audio system to provide mass notification operation.

  • Page 112: Time Functions: Real-Time Clock

    Operating Instructions Time Functions: Real-Time Clock Smoke Detector Data Smoke detector data is monitored by the FACP, eliminating the need to test the sensitivity of each detector at its location. A printout of ® each detector’s data can be retrieved from the FACP using an optional printer or Windows HyperTerminal.

  • Page 113: Special System Timers

    Special System Timers Operating Instructions  control panel LCD display will indicate a presignal event and the active point  control points programmed to Zone 097 will activate  outputs (NACs and control modules) of associated zones will be inhibited from activating for a factory set duration of 15 seconds ...

  • Page 114: 6: Control Module Delay Timer

    Operating Instructions Walktest 4.22.6 Control Module Delay Timer The control module delay feature, if enabled, will delay activation of a control module after a programmed time of 1-180 seconds after being triggered by an alarm condition. This feature requires the approval of the local Authority Having Jurisdiction. See the table on page 49 for allowable settings.

  • Page 115: 2=Zones

    Read Status Operating Instructions The operator selects the type of device which is to be viewed by pressing 1 for Detector or 2 for Module. If 1 is pressed, the display will change to the following screen: READ SYSTEM POINT ENTER DETECTOR# ...

  • Page 116: 3: Trouble Reminder

    Operating Instructions Read Status 4.24.3 Trouble Reminder Pressing 1 while viewing Read Status Screen #2 will display the following screen: READ STATUS 1=TROUBLE REMINDER TROUBLE REMINDER 2=TIMERS TROUBLE REM 24HR 3=NAC Read Status Screen #2 The screen indicates whether the Trouble Reminder feature is set to sound every 4 or 24 hours. 4.24.4 Timers Pressing 2 while viewing Read Status Screen #2 will cause the following Timer screens to be displayed: TIMERS...

  • Page 117: 8: History

    Read Status Operating Instructions Pressing 2 while viewing the Program Check screen #1 will display a screen which will indicate if any output zones have not been pro- grammed to at least one input zone. Use the up and down arrow keys to view all zones. Pressing 3 while viewing the Program Check screen #1 will display a screen which will indicate if any input zones have not been pro- grammed to at least one output zone.

  • Page 118: 11: Print

    Operating Instructions Read Status Pressing 2 for POTS Settings while viewing Communicator Screen #1 will display settings for the telephone portion of the Communica- tor. POTS SETTINGS 1=LINE 1 2=LINE 2 3=GAINS Pressing 1 or 2 will display whether each phone line is enabled Yes or disabled No, whether the phone type is touchtone or rotary, and whether the phone line is being supervised Yes or No.

  • Page 119: Chamber Value

    Read Status Operating Instructions Pressing 1 while viewing Print Screen #2 allows the user to print the detector data for each addressable smoke detector connected to the system. A printout, similar to the following example, will be generated if an optional printer is connected to the FACP. DEVICE # DEVICE TYPE % DRIFT COMP...

  • Page 120: 12: Time-Date

    Operating Instructions Read Status Figure 4.1 illustrates a graphic representation of the maintenance levels: DIRTY Maintenance Urgent Maintenance Alert Acceptable Range Low Chamber Reading VALUE Figure 4.1 Diagram of Maintenance Levels Pressing 2 while viewing Print Screen #2 allows the user to print the Communicator’s settings. Refer to PRINT “Communicator”...

  • Page 121: Section 5: Central Station Communications - Pots Transmission

    Section 5: Central Station Communications - POTS Transmission The control panel transmits zone and system status reports to Central Stations via the public switched telephone network. Two super- vised telephone line connections are made to interface the control panel to the telephone lines. Two optional 7 foot telephone cords are available for this purpose and can be purchased separately.
  • Page 122 Central Station Communications - POTS Transmission Transmittal Priorities Red LEDs are provided on the circuit board to identify which telephone line is activated. Also, a green LED labeled Kissoff will turn on whenever the control panel has successfully transmitted reports to the Central Station. The Kissoff LED may turn on several times during communications with a Central Station.

  • Page 123: Section 6: Fs-Tools Upload/Download

    Section 6: FS-Tools Upload/Download Important! The FACP will automatically reset 2 minutes after completion of a user program download via the FS-Tools programming utility. To prevent program corruption, the operator must wait until this panel reset occurs before performing any panel operations. The control panel may be programmed or interrogated off-site via an Ethernet connection or locally using a USB cable.

  • Page 124: 1: Security Features

    FS-Tools Upload/Download Transferring a Program  The control panel must be in the Normal Mode of operation. Downloading is not possible if the panel is in any other mode  There cannot be any active communications ongoing with a Central Station receiver ...

  • Page 125: Section 7: Usb Upload/Download

    Section 7: USB Upload/Download Important! The FACP will automatically reset 2 minutes after completion of a user program download. To prevent program corruption, the operator must wait until this panel reset occurs before performing any panel operations. CAUTION: After successfully downloading a program, make certain to perform the following steps: Print out all programmed data via Print Mode or manually view programmed entries and compare to intended program data Test all affected panel operations Immediately correct any problems found...
  • Page 126 USB Upload/Download USB Upload/Download Pressing 2 for Yes will cause the following screen to be displayed: USB UP/DOWNLOAD SYSTEM CONFIGURATION TRANSFER IN PROCESS PLEASE WAIT An error message will display if there is no USB drive inserted in the FACP or if there is no existing configuration saved on the USB drive.

  • Page 127: Section 8: Firmware Upgrade

    Section 8: Firmware Upgrade In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly recommend that you download the most current version of software for each product from www.firelite.com prior to commissioning any system.

  • Page 128: Section 9: Power Supply Calculations

    Section 9: Power Supply Calculations 9.1 Overview This section contains instructions and tables for calculating power supply currents in alarm and standby conditions. This is a four-step process, consisting of the following: Calculating the total amount of AC branch circuit current required to operate the system Calculating the worst-case system current load on the control panel, when primary (AC) power is applied, to assure that the limit of the its internal power supply will not be exceeded.
  • Page 129 Calculating the System Current Load Power Supply Calculations Calculation Column 1 Calculation Column 2 Calculation Column 3 Device Type Primary (AC) Power Source Secondary (Battery) Power Source Secondary (Battery) Power Source Fire Alarm Current (amps) Fire Alarm Current (amps) Standby Current (amps) X[current draw]= Total X [current draw]=...

  • Page 130: Calculating The Battery Size

    Power Supply Calculations Calculating the Battery Size 9.4 Calculating the Battery Size Use Table 9.4 to calculate the total Standby and Alarm load in ampere hours (AH). This total load determines the battery size (in AH), required to support the system upon loss of primary (AC) power. Complete Table 9.4 as follows: Enter the totals from Table 9.3 on page 129, Calculation Columns 2 and 3 where shown Enter the NFPA Standby and Alarm times (refer to ‘NFPA Requirements’...

  • Page 131: Appendix A: Software Zones

    Appendix A: Software Zones A.1 Correlations Setup and configuration of an addressable system is different than a conventional system. In a conventional system, assignment of input devices (smoke detectors, pull stations, heat detectors, etc.) to zones is accomplished through wiring. The wiring is direct from clearly marked panel terminals to any device assigned to a particular zone.
  • Page 132 Software Zones Correlations Correlation of Input and Output Zones Input Devices Zones Output Devices smoke control smoke control ZONE monitor control monitor control control monitor control smoke ZONE control smoke smoke control smoke ZONE smoke control monitor ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...
  • Page 133 Correlations Software Zones The zone correlations which are shown graphically above are also presented in Table A.1 on page 133 and Table A.2 on page 134. DETECTOR ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN smoke FIRST HALL...
  • Page 134 Software Zones Correlations MONITOR/CONTROL MODULE ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN monitor monitor 1, 2 monitor 1, 2 monitor control control control control control 1, 2, 3 control Table A.2 Module Programming Sheet Example ES-200X Series Manual —...
  • Page 135 Correlations Software Zones DETECTOR ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN Table A.3 Blank Detector Programming Sheet ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...
  • Page 136 Software Zones Correlations MONITOR/CONTROL MODULE ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN Table A.4 Blank Module Programming Sheet ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...
  • Page 137 Notes ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...

  • Page 138: Appendix B: Default Programming

    Appendix B: Default Programming The following table provides a list of the programming options and their factory default settings. Program Option Factory Default Program Option Factory Default Detector Programming Not Installed Aux Power Class A Detector Type Smoke-Photo Aux Power Resettable Detector Verification Aux Power 2 Resettable Detector Walktest...

  • Page 139: Appendix C: Nfpa Standard-Specific Requirements

    Appendix C: NFPA Standard-Specific Requirements The ES-200X has been designed for use in commercial, industrial, and institutional applications and meets the requirements for service under the National Fire Protection Association (NFPA) Standards outlined in this Appendix. The minimum system components required for compliance with the appropriate NFPA standard are listed below: ES-200X Control Panel Contains the main control board, cabinet (backbox and door), main power supply transformer and power supply.
  • Page 140 NFPA Standard-Specific Requirements NFPA 72 Remote Station Protective Signaling System Notes: Cut Jumper JP3 on the ES-200X main circuit board to supervise placement of the 4XTMF module. Refer to “4XTMF Transmitter Module Installation” on page 31 for detailed information. RS82 Remote Station Receiver UL listed. Refer to Instruction Manual for Remote Station Receiver Model RS82.
  • Page 141 NFPA Standard-Specific Requirements NFPA 72 Proprietary Protective Signaling Systems ES-200X Addressable Fire Control Panel ES-200X Main Board Form-C Alarm contact programmed to activate on General Alarm. Form-C Trouble contact which will automatically activate on any Trouble condition. Form-C relay contact programmed to activate on Supervisory condition.

  • Page 142: C.1: Mbt-1 Municipal Box Trip - Silenceable

    NFPA Standard-Specific Requirements MBT-1 Municipal Box Trip - Silenceable C.1 MBT-1 Municipal Box Trip - Silenceable The following figure illustrates the connection of the MBT-1 (Municipal Box Trip) between the FACP and a Local Energy Municipal Box. The use of an addressable control module programmed for General Alarm and Silenceable allows silencing of the Municipal Box without resetting the panel or box.

  • Page 143: Appendix D: Wire Requirements

    Appendix D: Wire Requirements T-tapping of the SLC loop wiring is allowed for 2-wire (Class B) configurations. The total resistance of any branch cannot exceed 40 ohms. The total wire length of all branches cannot exceed 10,000 feet (3,000 m). Connecting external system accessories to the ES-200X main circuits must be carefully considered to ensure proper operation.

  • Page 144: D.1: Nac Wiring

    Wire Requirements NAC Wiring D.1 NAC Wiring The following table lists NAC wiring requirements for the FACP. CLASS-B CLASS-A Max. Max. allowable wire pair length Max. allowable wire pair length allowable NAC Load (feet) (feet) total loop (Amps) resistance AWG 12 AWG 14 AWG 16 AWG 18...

  • Page 145: Appendix E: Hvac Control

    Appendix E: HVAC Control The FACP can be programmed to shut down a building’s HVAC fans in the event of a fire. The fans cannot be restarted until the fire alarm condition has been cleared and the FACP has been reset to a normal (non-alarm) condition. IMPORTANT! This HVAC feature is not to be used for smoke control.

  • Page 146: E.2: Monitor Module Operation

    HVAC Control Monitor Module Operation E.2 Monitor Module Operation E.2.1 HVAC RESTART The HVAC RESTART type code can be assigned to any addressable monitor module for the purpose of resetting (deactivating) the HVAC SHUTDN control module and turning the fans back on. The HVAC RESTART monitor module acts globally throughout the FACP system and therefore is not programmed to a particular software zone.

  • Page 147: Appendix F: Ademco Contact Id Format Event Code Descriptions

    Appendix F: Ademco Contact ID Format Event Code Descriptions This appendix describes the various Event Codes and their messages which are available for the Ademco Contact ID Format. F.1 Transmission Format Between DACT and Receiver The transmission string for the Ademco Contact ID Format is as follows: SSSS 18 QXYZ GG CCC where SSSS...
  • Page 148 Ademco Contact ID Format Event Code Descriptions Ademco Contact ID Typical Printout EVENT CODE CLASSIFICATIONS ALARMS SUPERVISORY TROUBLES OPEN/CLOSE DISABLES/BY TEST/MISC. REMOTE ACCESS PASSES Medical Fire System Open/Close System Test Fire Sounder/Relay Remote Access Sounder/Relay Panic System Peripheral Access Control System Peripheral Burglary Communication...
  • Page 149 Ademco Contact ID Typical Printout Ademco Contact ID Format Event Code Descriptions EVENT MESSAGE 24-Hour Non-Burglary - 150 and 160 150 24-Hour Non-Burg ALARM - 24-Hr. Non-Burg - # 151 Gas detected ALARM - Gas Detected - # 152 Refrigeration ALARM - Refrigeration - # 153 Loss of heat ALARM - Heating System - #...
  • Page 150 Ademco Contact ID Format Event Code Descriptions Ademco Contact ID Typical Printout EVENT MESSAGE Communication Troubles - 350 and 360 350 Communication TROUBLE - Communication Trouble 351 Telco 1 fault TROUBLE - Phone Line #1 352 Telco 2 fault TROUBLE - Phone Line #2 353 Long range radio transmitter fault TROUBLE - Radio Transmitter 354 Fail to communicate...
  • Page 151 Ademco Contact ID Typical Printout Ademco Contact ID Format Event Code Descriptions EVENT MESSAGE 527 Bell 4 disable DISABLE - Bell/Siren - #4 System Peripheral Disables - 530 and 540 Communication Disables - 550 and 560 551 Dialer disabled DISABLE - Dialer Disable 552 Radio transmitter disabled DISABLE - Radio Disable Bypasses - 570...

  • Page 152: Appendix G: Central Station Points

    Appendix G: Central Station Points The control panel transmits Central Station Reports in a numerical format which indicates the FACP addressable device address that is reporting. The following table indicates the Central Station Report (CS Report) number that will be transmitted and the addressable device address it represents.
  • Page 153 Central Station Points Module Module Module Module Report Address Report Address Report Address Report Address Table G.2 Addressable MODULES ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...

  • Page 154: Appendix H: Nfpa Requirements

    Appendix H: NFPA Requirements The following is the minimum configuration to meet the NFPA requirements. Process Module Local Proprietary Management ES-200X ES-200XC IPOTS-COM (pre-installed communicator) 4XTMF DP-ES-R BB-55F ANN-LED ANN-80 ANN-100 ANN-S/PG ANN-I/O ANN-RLED ANN-RLY Where Y = Yes, N = No, and O = Optional Non-Emergency One of the indicated modules is required when the IPOTS-COM is not employed.

  • Page 155: Appendix I: Open/Short/Ground Trip Values

    Appendix I: Open/Short/Ground Trip Values Table I.1 lists the earth fault resistance detection for each applicable terminal on the FACP. Output Circuit Terminal Trip Resistance (in ohms) Remote Sync 360K Remote Sync 330K NAC 1-2 360K NAC 1-2 320K ANN Bus 270K ANN Bus 265K...

  • Page 156: Appendix J: Canadian Applications

    ANN-LED metal conduit (adjacent to FACP) ANN-LED FACP ANN-100 ANN-I/O FIRE SYSTEM SYSTEM ACTIVE CALL CONTROL ANN-S/PG ® by Honeywell optional ANN-RLY ECC-50/100 audio system Figure J.1 FACP Minimum Configuration - Single ANN-LED ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...
  • Page 157 ANN-RLY When using an audio system, 7 ANN-LEDs can be used . FIRE SYSTEM SYSTEM ACTIVE CALL CONTROL ® by Honeywell optional ECC-50/100 audio system Figure J.2 FACP Maximum Configuration - Eight ANN-LEDs ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...
  • Page 158 Canadian Applications Notes: 1. The CRF-300 and the MMF-300 must be mapped to the same zone TB12- which is programmed for supervisory SLC Loop operation. Output 2. No other device can be mapped to MMF-300* that supervisory zone. 3. Wire gauge must be 18AWG minimum.

  • Page 159: Index

    Index Numerics ANN-SB80KIT mounting kit 37 class B annunciator guidelines 19 NAC wiring 27 24 hour test time 85 annunciator module 14 Classic Loop Interface Protocol 71 24VDC power 71 annunciators 19 CLIP mode 4XTMF module 139 Audio Command Center 14 see also Classic Loop Interface Protocol 71 coil resistance 31 audio panel control 47...
  • Page 160 Index enable/disable 55 see also fire alarm control panel 13 Disabled 107 programming 53 features 13 Fire Alarm 106 screen display 54 fire alarm control panel Ground 106 type 55 see also FACP 13 Maintenance 107 verification 56 firefighter telephone 47 see also Indicators 16 wireless 57 firmware upgrade 127...
  • Page 161 Index PAS timer 74 level 2 51 silence inhibit 78 password 13 manual 50 silenceable 76 change 99 master level 1 52 synchronized 112 invalid 99 modules 60 type codes 76 maintenance level 2 101 off-line computer 50 voltage drop 14 phone line supervision 82 via computer keyboard 49 voltage, operating 14...
  • Page 162 Index secondary communication path 84 synchronized signals 112 waterflow delay timer 74 secondary power requirements 130 and silenceable circuits 76 waterflow retard Timer 113 secret code 124 system waterflow silenceable 71 security features 124 maintenance level 104 W-GATE 19 sensitivity 112 system point 114 wiring 47 see also smoke detector sensitivity 112...

  • Page 163: Slide-In Labels

    Slide-in Labels Carefully cut along the outside of each label. Identify Function (F1-F4) keys as desired and slide the labels into the keypad. Starting at the center of the keypad next to the Function Keys, slide each label into the groove towards the outer edge. Function Keys F1 and F3 are not programmable in Canadian applications.
  • Page 164 ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018...

  • Page 165: 200X And Es-200Xc Fire Alarm Control Panels Operating Instructions

    ES-200X and ES-200XC Fire Alarm Control Panels Operating Instructions NORMAL - Only AC POWER is illuminated green. PANEL KEY - The key to open the panel can be found at the following All other indicators are off. LCD display will read SYSTEM NORMAL. location: ________________________________________________________ WHEN AUDIBLE DEVICES ARE SOUNDING -...
  • Page 167 Manufacturer Warranties and Limitation of Liability Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer warrants that the Products manufactured by it in its Northford, Connecticut facility and sold by it to its authorized Distributors shall be free, under normal use and service, from defects in material and workmanship for a period of thirty six months (36) months from the date of manufacture (effective Jan.
  • Page 168 One Fire-Lite Place, Northford, CT 06472-1601 USA USA - Phone: (203) 484-7161 Canada - Phone: (905) 856-8733 www.firelite.com...

This manual is also suitable for:

Fire-lite alarms es-200xc

Table of Contents