Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt XR LI-ION DCG405NT
Summary of Contents for DeWalt XR LI-ION DCG405NT
- Page 1 DCG405 Final page size: A5 (148mm x 210mm)
- Page 2 Fig. A 90˚ 90˚ Fig. B...
- Page 3 Fig. C Fig. D Fig. E Fig. F Fig. G...
-
Page 4: Technical Data
EnGLIsh CORDLESS SMALL ANGLE GRINDER DCG405 Congratulations! EC-Declaration of Conformity You have chosen a D WALT tool. Years of experience, thorough Machinery Directive product development and innovation make D WALT one of the most reliable partners for professional power tool users. Technical Data Cordless Small Angle Grinder DCG405... -
Page 5: Work Area Safety
Weight EnGLIsh Batteries Chargers/Charge Times (Minutes) Cat # Weight (kg) DCB107 DCB113 DCB115 DCB118 DCB132 DCB119 DCB546 18/54 6.0/2.0 1.05 DCB547 18/54 9.0/3.0 1.25 DCB181 0.35 DCB182 0.61 DCB183/B 0.40 DCB184/B 0.62 DCB185 0.35 DCB187 0.48 General Power Tool Safety Warnings f ) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) WARNING: Read all safety warnings and all... -
Page 6: Safety Instructions For All Operations
EnGLIsh b ) Do not use the power tool if the switch does not turn all safety warnings, instructions, illustrations and it on and off. Any power tool that cannot be controlled specifications provided with this power tool. Failure with the switch is dangerous and must be repaired. to follow all instructions listed below may result in electric shock, fire and/or serious injury. -
Page 7: Causes And Operator Prevention Of Kickback
EnGLIsh cutting tool may contact hidden wiring. Contact d ) Use special care when working corners, sharp edges with a "live" wire will also make exposed metal parts etc. Avoid bouncing and snagging the accessory. of the power tool "live" and could give the operator an Corners, sharp edges or bouncing have a tendency to electric shock. -
Page 8: Important Safety Instructions For All Battery Chargers
EnGLIsh a complete stop. Never attempt to remove the cut- • Risk of personal injury due to prolonged use. off wheel from the cut while the wheel is in motion • Risk of dust from hazardous substances. otherwise kickback may occur. Investigate and take Electrical Safety corrective action to eliminate the cause of wheel binding. -
Page 9: Charger Operation
EnGLIsh NOTICE: Under certain conditions, with the charger 2. Insert the battery pack into the charger, making sure the 10 plugged into the power supply, the exposed charging battery pack is fully seated in the charger. The red (charging) contacts inside the charger can be shorted by foreign light will blink repeatedly indicating that the charging material. -
Page 10: Wall Mounting
EnGLIsh Wall Mounting Contents of opened battery cells may cause respiratory • irritation. Provide fresh air. If symptoms persists, seek These chargers are designed to be wall mountable or to sit medical attention. upright on a table or work surface. If wall mounting, locate the WARNING: Burn hazard. -
Page 11: Storage Recommendations
EnGLIsh The information provided in this section of the manual is provided in good faith and believed to be accurate at the time Do not probe with conductive objects. the document was created. However, no warranty, expressed or implied, is given. It is the buyer’s responsibility to ensure that its Do not charge damaged battery packs. -
Page 12: Intended Use
EnGLIsh Markings on Tool Features The following pictograms are shown on the tool: Kickback Brake™ When a pinch, stall, or bind-up event is sensed, the electronic Read instruction manual before use. brake engages with maximum force to quickly stop the wheel, reduce the movement of the grinder, and shut the grinder off. - Page 13 EnGLIsh To Remove the Battery Pack from the Tool wheel where surface grinding is forbidden. Cutting can also be performed by using a Type 41 wheel and a Type 1 guard. 1. Press the release button 11 and firmly pull the battery pack nOTE: See the Accessories Chart to select the proper guard / out of the tool handle.
-
Page 14: Prior To Operation
EnGLIsh 1. Place the tool on a table, guard up. Mounting Wire Cup Brushes and Wire Wheels (Fig. A) 2. Install the backing flange 6 on spindle 4 with the raised centre (pilot) facing the wheel. Press the backing flange WARNING: Failure to properly seat the flange/ clamp nut/ into place. - Page 15 EnGLIsh WARNING: To start the tool, slide the ON/OFF slider switch toward 1 the front of the tool. To stop the tool, release the ON/OFF • Ensure all materials to be ground or cut are secured slider switch. in place. For continuous operation, slide the switch toward the front of •...
-
Page 16: Cutting Metal
EnGLIsh nOTE: Allowing the tool to rest on the work surface without not designed for side pressures encountered with surface moving will damage the work piece. grinding. Wheel breakage and injury may result. 5. Remove the tool from work surface before turning tool off. CAUTION: Wheels used for edge grinding and cutting Allow the tool to stop rotating before laying it down. - Page 17 EnGLIsh will not become too hot, does not discolour and no grooves Max. Min. Periphical Threaded are formed. [mm] Rotation speed hole length [mm] Cutting Stone [min. –1 [m/s] [mm] The machine shall be used only for dry cutting. 115 6 22,23 11 500 –...
-
Page 18: Accessory Chart
EnGLIsh Accessory Chart Guard Type accessory Description how to Fit Grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Locking flange Wire wheels with threaded nut Type 27 guard Wire wheel Wire cup with threaded nut... - Page 19 EnGLIsh Accessory Chart (cont.) Guard Type accessory Description how to Fit Grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal cutting disc, bonded Backing flange Diamond cutting wheels Type 1 Guard Cutting wheel Type 27 Guard Locking flange...