Sony PXW-Z190T Operating Instructions Manual page 65

Notes
• Streaming cannot be started under the following menu
settings.
 When Rec Format >Codec in the System menu is
set to DVCAM(MXF)
 When S&Q Motion >Setting in the Recording
menu is set to On
 When Interval Rec >Setting in the Recording menu
is set to On
 When Simul Rec >Setting in the Recording menu is
set to On
• Changing to network client mode during normal
streaming (page 62) or RTMP streaming (page 67) is
not possible.
• After changing to network client mode, normal
streaming and monitoring (page 70) are not available.
• Changing to network client mode while monitoring
will stop the monitoring.
• File transfer is not supported during streaming in
network client mode. File transfer is supported after
stopping streaming.
• If streaming in network client mode is started during
file transfer, the file transfer stops. File transfer restarts
after stopping streaming.
• User Name, Password, and certificates are not saved in
an ALL file, so these must be configured again after
loading an ALL file.
• If Setting is set to Off while streaming in network
client mode, streaming stops.
• When streaming in network client mode, NCM
Settings Select and the NCM Settings selected using
NCM Settings Select cannot be changed.
• During streaming, the screen information update
frequency is reduced, but this does not affect
operation.
• The recording settings cannot be changed during
streaming in network client mode.
• The wired LAN settings cannot be changed during
streaming in network client mode.
• The image may momentarily stop when switching to
the thumbnail screen or playback screen during QoS
streaming.
• The distribution formats available for streaming vary
depending on the Rec Format setting of the camcorder.
Transferring files in network client mode
You can transfer files to a server set by the CCM
by connecting a Network RX Station acting as a
CCM and the camcorder in network client mode.
1
Select the file to upload.
• To transfer a proxy recording:
Follow steps 1 to 4 in "Uploading a proxy
file on an SD card" (page 72).
• To transfer original files:
Follow steps 1 to 4 in "Uploading an
original file on a memory card" (page 72).
2
Tap Transfer.
"NCM: RX Server" is displayed as a
destination.
Specify "NCM: RX Server" as the
destination.
3
Tap Transfer.
Transfer of the selected files to the server
specified on the CCM starts.
Note
• The destination can also be set to "NCM: RX Server"
when not in network client mode. In this case, transfer
is placed on hold, and then transfer to the server
specified on the CCM starts after connecting to the
CCM in network client mode.
Intercom calling in network client mode
Using network client mode, you can conduct
intercom calls between the camcorder and a
Network RX Station CCM or XDCAM air using
a headset connected to the USB 3.0 (HOST)
connector of the camcorder.
Note
• Always connect the headset to the USB 3.0 (HOST)
connector of the camcorder.
• The connection standard is USB 2.0 equivalent.
• Correct operation is not guaranteed if the headset is
connected via a USB hub.
• Correct operation is not guaranteed if headsets are
connected to both the USB 3.0 (HOST) connector and
USB 2.0 (HOST) connector.
• The intercom calling function may no longer operate
when a headset is connected to the USB 2.0 (HOST)
connector. First remove the headset connected to the
USB 2.0 (HOST) connector, and then set to the power
switch to the STANDBY position and then back to the
ON position.
• If Network Client Mode >Setting is set to Off during
an intercom call, the intercom call stops.
• If NCM Settings Select and the NCM Settings selected
using NCM Settings Select are changed during an
intercom call, the intercom call stops.
• The intercom call start signal cannot be sent from a
CCM or XDCAM air to the camcorder under the
following menu settings.
 When Focus >Face Detection AF in the Camera
menu is set to Face Only AF or Face Priority AF
 When Proxy Rec >Setting in the Recording menu is
set to On
 When 4K & HD (Sub) Rec >Setting in the
Recording menu is set to On
1
Connect the camcorder to the Internet
as described in "Connecting to the
Internet" (page 57).
65