Table of Contents
Advertisement
DISPLAY PROTECTION
POWER SAVE
AUTO POWER SAVE
TIME SETTING
POWER SAVE MESSAGE
FAN CONTROL
HEAT STATUS
SCREEN SAVER
GAMMA*
1
BACKLIGHT*
1
MOTION*
2
SIDE BORDER COLOR
POWER ON DELAY
DELAY TIME
LINK TO ID
ALERT MAIL
INTELLI. WIRELESS DATA Select [ON] to activate INTELLIGENT WIRELESS DATA function (see
RESET
CONTROL
NETWORK INFORMATION Shows the current network settings.
LAN
IP SETTING
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
DNS
DNS PRIMARY
DNS SECONDARY
*1: If [SPECTRAVIEW ENGINE] is [ON], this function is grayed out.
*2: When you select [OPTION] for signal input, this function depends on which Option Board you are using.
*3: The function is available only when connecting the optional control unit.
Set [ENABLE] or [DISABLE]. If you set it to [ENABLE], set how long the monitor waits to go into power save
mode after signal is lost. For more details please check the [POWER INDICATOR] (See
NOTE: The display card might not stop sending the digital data even though the image might have disappeared.
If this occurs the monitor will not switch into power management mode. [POWER SAVE] is disabled when [AUTO
OFF] or [CUSTOM] is selected in [HUMAN SENSING]*
Set the time when the monitor goes into auto power save mode after signal is lost.
When the monitor goes into power save mode, a message is displayed when [ON] is selected.
Cooling fans will reduce the internal temperature of the monitor to protect it from overheating.
If [AUTO] is selected, you can adjust the start temperature of the cooling fans and the fan speed.
Shows the actual status of the fans, backlight and temperature sensors.
Use the [SCREEN SAVER] function to reduce the risk of Image Persistence.
NOTE: When the screen saver is activated, the image will be changed to [FULL] image. After the screen saver
stops, the image will be reproduced again with the current [ASPECT] setting.
The [SCREEN SAVER] cannot be selected for 3840 x 2160 (60 Hz) nor 4096 x 2160 (60 Hz) signal input.
When the [SCREEN SAVER] is set to active, [MULTI PICTURE MODE], STILL, [IMAGE FLIP] (except for
[NONE]) or [TEXT TICKER], POINT ZOOM, [TILE MATRIX] are not available.
The monitor gamma is changed and fixed when [ON] is selected.
The brightness of the backlight is decreased when [ON] is selected.
NOTE: Do not select this function when [ROOM LIGHT SENSING] is set to [MODE1] or [MODE2].
The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at user determined
intervals. You can set interval time and zoom ratio.
Adjusts the color of the side borders when a 4:3 image is reproduced.
By pressing the + button on the remote control, the side borders will become brighter.
By pressing the - button, the side borders will become darker.
Background color of the Media Player window is also changed.
Adjusts the delay time between being in "standby" mode and entering "power on" mode.
[POWER ON DELAY] can be set between 0 and 50 seconds.
When [ON] is selected, the delay time is linked with the Monitor ID. It takes more time when there are a large
number of IDs.
Set [ON] to activate alert mail (See
using the function.
Resets all settings within the [DISPLAY PROTECTION] menu back to factory setting except for [POWER ON
DELAY] and [INTELLI. WIRELESS DATA].
NOTE: When changing any LAN settings, you need to wait several seconds until modified LAN settings are
applied.
Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to enter a fixed IP address and subnet mask data obtained from your network
administrator.
NOTE: Consult your network administrator for the IP address when [AUTO] is selected for [IP SETTING].
Set your IP address for the monitor connected to the network when [MANUAL] is selected for [IP SETTING].
Set your subnet mask data for the monitor connected to the network when [MANUAL] is selected for
[IP SETTING].
Set your default gateway for the monitor connected to the network when [MANUAL] is selected for [IP SETTING].
NOTE: Enter [0.0.0.0] to delete the setting.
Set the IP addresses of DNS servers.
AUTO: The DNS server, which is connected with the monitor, will automatically assign its IP address.
MANUAL: Manually enter the IP address of the DNS server which is connected with the monitor.
Enter the primary DNS server settings of the network connected with the monitor.
NOTE: Enter [0.0.0.0] to delete the setting.
Enter the secondary DNS server settings of the network connected with the monitor.
NOTE: Enter [0.0.0.0] to delete the setting.
3
.
page
53).
English-40
page
42).
page
60). A password is required when
Advertisement
Table of Contents
