The Image Adjustment Menu; The Default Setting Menu; The Display Setting Menu; Reset Menu (Special Menu) - Toshiba TLP S70 Owner's Manual

Using the menu (Continued)

The image adjustment menu

Use this menu to adjust image-related items.
Items that can be adjusted are marked with "Yes", and those that cannot are marked with "No".
Item Description
Contrast Lower Higher
Brightness Darker Brighter
Color Lighter Deeper
[Note 1]
Tint Reddish Greenish
Sharpness Softer Sharper
R-level Less red More red
G-level Less green More green
B-level Less blue More blue
Up/down shift [Note 2] Shift down Shift up
Notes
1: Tint can only be adjusted when Video mode is set to NTSC or NTSC4.43.
2: Up/down shift can only be adjusted when Screen size

The default setting menu

This menu shows placement status and other settings.
Item
Projection
Sets projection mode in accordance with Placement Style
mode
(Placed
on floor)
No signal
Sets the period of time to wait until turning off the power after signal input stops:
power off
Off (not turned off)
Power on
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual
Sets the lamp power
Lamp power [Note 1]
Sets the camera's shutter speed to either (50Hz) or (60Hz). 50Hz
Shutter speed
Sets the camera's white balance to (Auto) or (Fixed). Auto
White balance
[Note 2]
Notes
1: When lamp power is set to low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off. The setting will be back to
"Standard" when the power is turned on next time.
2: White balance, if set to Fixed, is reset upon power off and the Auto is resumed the next time the
unit is turned on. (Models with the document camera)
Notes
• Note that if Power on is set to Auto, then if the power cord is plugged in when power is
restored after a power outage, the projector power will come on.
• Even if Power on is set to Auto, press the ON/STANDBY button to turn off the power.
Unplugging the power cord to cut off the power will shorten the life of the lamp.
Computer Y/P /P Video S-video Camera
B R
Yes Yes Yes Yes
Yes Yes Yes Yes
No Yes Yes Yes
No No Yes Yes
No Yes Yes Yes
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes Yes Yes Yes
No Yes Yes Yes
p.33 is set Wide.
Description
p.19
(Hung from (Back hung
(Rear)
ceiling) from ceiling)
1 min 2 min ... 60 min
Standard Low
Fixed.
32

The display setting menu

Use this menu to set screen display-related items.
Item
Screen size
Yes
Yes
No
No Language
Yes
Yes
Yes
Background
Yes
Icon
No
Start-up screen
Notes
• If "Thru" is selected for screen size, portions exceeding the pixel count of the LCD panel
p.45 will not appear on the screen. Note that for RGB signals with clock speeds
SXGA3_60 p.46 or lower, all input pixel signals are sampled. (This effect is noticeable
when the screen is enlarged using the Resize function
is higher than this, the RGB pixel signal is reduced before sampling.
• Displaying the images with the aspect ratio different from the original with the purpose of
other than the personal and private viewing, using the screen size menu may violate the
copyright protected by the law.

Reset menu (Special menu)

Auto
When other menus are not displayed and the
• When the screen is placed vertically, and Auto keystone correction is executed, but the
keystone correction is not successful, stow the foot adjuster in its original position, place
60Hz.
the projector on a flat surface, select Horizontal reference value reset, and press the
button.
• Select Reset All and press the
Item
Horizontal reference
value reset
Reset all
Description
(Full): Display with LCD panel's resolution
(Thru): Display with sampling resolution (for computer input)
(Wide): Wide-screen display (for Video, S-video, and Y/P
Select one of the languages below to use for displaying menus and messages
[ : Enter setting mode] [ :Selection]
English/Français/Deutsch/Italiano/Español/
Português/ / /
Screen to display when there is no input signal
Display icons as function guides
Display start-up screen when power turned on
p.29
button is held down, the menu appears.
button to return all menu items to the factory settings.
Description
Reset the horizontal reference value for Auto keystone correction
[ : Enter execution mode] [Yes
Reset all menu items to their factory settings
[ : Enter execution mode] [Yes
33
/P )
B R
[Apply: ]
/
(Logo) (Blue) (None)
On Off
On Off
). However, if the clock speed
No] [Apply: ]
No] [Apply: ]