Configuring The Machine's Wireless Network; Completing The Installation; Troubleshooting - Samsung CLP-320K User Manual

3. Click the Firewall menu.
4. Turn firewall off.
The following instructions may vary for your model.
1. Connect your machine to the network with a network cable.
2. Insert the Installation CD-ROM, and open the disk window, select
MAC_Installer > MAC_Printer > SetIP > SetIPApplet.html.
3. Double click the file and Safari will automatically open, then select
Trust. The browser will open the SetIPApplet.html page that shows
the printer's name and IP address information.
4. Click on the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5. Enter the machine's new information into the configuration window
as follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
• MAC Address: Find the machine's MAC address from the
Network Configuration Report and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
• IP Address: Enter a new IP address for your printer.
For example, if your computer's IP address is 192.168.1.150,
enter 192.168.1.X. (X is number between 1 and 254 other than
the computer's address.)
• Subnet Mask: Enter a Subnet Mask.
• Default Gateway: Enter a Default Gateway.
6. Select Apply, then OK, and OK again. The printer will automatically
print the configuration report. Confirm that all the settings are correct.
Quit Safari. You may close and eject the installation CD-ROM. If
necessary, restart the computer's firewall. You have successfully
changed the IP address, subnet mask, and gateway.

Configuring the machine's wireless network

Before starting you will need to know the network name(SSID) of your
wireless network and the network key if it is encrypted. This information was
set when the access point (or wireless router) was installed. If you do not
know about your wireless environment, please ask the person who has set
up your network.
To configure wireless parameters, you can use SyncThru™ Web Service.
Using SyncThru™ Web Service
Before starting wireless parameter configuration, make sure cable
connection status.
1. Check whether the network cable is connected to the machine. If not,
connect the machine with a standard network cable.
2. Start a web browser such as Internet Explorer, Safari or Firefox and
enter your machine's new IP address in the browser window.
For example,
3. Click Login on the upper right of the SyncThru™ Web Service
website.
A log-in page appears.
4. Type in the ID and Password then click Login.
If it's your first time logging into SyncThru™ Web Service, type in the
below default ID and password.
• ID: admin
• Password: sec00000
5. When the SyncThru™ Web Service window opens, click Network
Settings.
Wireless network setup (CLP-325W(K) only)_ 44
6. Click Wireless > Wizard.
Wizard will help you setup the wireless network configuration.
However, if you want to set the wireless network directly, select
Custom.
7. Select the one Network Name(SSID) in the list.
• SSID: SSID (Service Set Identifier) is a name that identifies a
wireless network. access points and wireless devices attempting
to connect to a specific wireless network must use the same
SSID. The SSID is case-sensitive.
• Operation Mode: Operation Mode refers to the type of wireless
connections (See "Wireless network name and network key" on
page 38).
- Ad-hoc: Allows wireless devices to communicate directly with
each other in a peer-to-peer environment.
- Infrastructure: Allows wireless devices to communicate with
each other through an access point.
If your network's Operation Mode is Infrastructure, select the
SSID of the access point. If the Operation Mode is Ad-hoc,
select the machine's SSID. Note that "airportthru" is the default
SSID of your machine.
8. Click Next.
If wireless security setting window appears, enter the registered
password (network key) and click Next.
9. The confirmation window appears, please check your wireless setup.
If the setup is right, click Apply.
Disconnect the network cable (standard or network). Your
machine should then start communicating wirelessly with the
network. In case of Ad-hoc mode, you can use a wireless LAN
and wired LAN simultaneously.

COMPLETING THE INSTALLATION

After you have installed your Samsung wireless network printer, print
another copy of the Network Configuration Report and keep it for future
reference. You are now ready to use your new Samsung wireless printer on
your network.
If the wireless network seems to not be working, set all the network
setting to the factory defaults and try again (See "Restoring factory
default settings using SyncThru™ Web Service" on page 33).

TROUBLESHOOTING

Solving problems that might occur during wireless
setting and installing the machine driver
Printers Not Found
• Your machine may not be turned on. Turn on your computer and the
machine.
• USB cable is not connected between your computer and machine.
Connect machine to your computer using the USB cable.
• The machine does not support wireless network. Check the
machine's user's guide included on the software CD supplied with
your machine and prepare a wireless network machine.
Connecting Failure - Not found SSID
• The machine is unable to search network name (SSID) which you
have selected or typed in. Check the network name (SSID) on your