Table of Contents
Advertisement
Operating the Setting Menu
Making Basic Settings
Projector's buttons
SETTING button
MERGENCY
AV
RGB
SETTING
QUICK
ALIGN.
QUICK ALIGN. button
Setting menu
S E T T I N G
T R A C K I N G
1 0
P H A S E
0
H . P O S .
0
V . P O S .
0
F O C U S
–
+
Z O O M
W
T
S I F T L E N S
Adjustment • setting level
Description of adjustment and setting items
TRACKING
: If wide vertical stripes appear on the screen,
adjust the lateral video size and display area
so that they disappear. (–255 ↔ 0 ↔ +255)
PHASE
: If characters on the screen flicker or become
dim, adjust so they become clear.
(–127 ↔ 0 ↔ +127)
H. POS.
: If the screen position is displaced to the right
or left, adjust the horizontal position of the
screen. (–255 ↔ 0 ↔ +255)
V. POS.
: If the screen position is displaced upward or
downward, adjust the vertical position of the
screen. (–120 ↔ 0 ↔ +120)
FOCUS
: Adjust the focus of video picture.
–: Focuses on near points.
+: Focuses on farther points.
ZOOM
: Adjust the screen size (angle of view).
T : Becomes smaller.
W : Becomes larger.
SIFT LENS
: Adjusts the projected screen position.
∞: Moves it down.
5: Moves it up.
30
In this section, we are making basic picture adjustments which
should be performed after installation (connection).
Notes
• The setting menu is displayed when you press the SETTING button
on the projector. After the menu is displayed, you can make settings
(adjustments).
• If the projector's position or connections have been changed,
adjustments and settings should be performed again.
• After adjustments, if further picture adjustment is necessary
depending on the equipment connected, use the main menu (pages
33 to 58) to make detailed settings and adjustments.
• For computer-related inputs, use of the quick alignment function
allows automatic adjustment of TRACKING, PHASE, H. POS. and
V. POS. (See pages 30, 36 and 37).
1
Press the SETTING button of the
projector.
• The setting menu is displayed on the screen.
Press the SETTING button to
2
select the desired item.
• The selected item is shown in magenta color. Each time
you press the button, the selected item changes as
follows:
TRACKING
PHASE
H. POS.
V. POS.
Menu clearing
SIFT LENS
ZOOM
FOCUS
Memo
To select items using the remote control unit:
Items can be selected using the cursor buttons 5 (backward) or
∞(forward) on the remote control unit. In this case, menu clearing in
the above order is not available. The selection changes from SIFT
LENS to TRACKING directly.
3
Adjust and set the selected item
using the QUICK ALIGN. buttons
or
.
• To adjust and set multiple items, repeat steps 2 and 3.
• To reset the adjustment value of the selected item
(TRACKING, PHASE, H. POS. or V. POS.) to the
factory-set value, press the remote control's PRESET
button. This button does not work for focus and zoom.
Memo
To adjust and set items using the remote control unit:
Items can be adjusted or set by pressing the MENU/ENTER button
toward the 2 or 3 mark on the remote control.
Clear the setting menu by
4
pressing the SETTING button
repeatedly.
Memo
To clear the setting menu using the remote control unit:
You can also clear the setting menu by pressing the PAGE BACK
button on the remote control unit.
Operating the Main Menu
Configuration the Main Menu (AV Input)
You can adjust video quality (PICTURE) and etc. using the menus.
The menus are configured as follows:
Main menu (AV inputs : During EXT. IN input signal)
PIXEL CLOCK
TRACKING
: Normally, no adjustment is required. The lateral size and display area of video image are adjusted.
PHASE
: Normally, no adjustment is required. Flickering or dim video image is adjusted.
POSITION
V. POS.
: The vertical position of the video image being projected is adjusted.
H. POS.
: The horizontal position of the video image being projected is adjusted.
PICTURE
BRIGHTNESS
: The brightness of the video image being projected is adjusted.
CONTRAST
: The contrast of the video image being projected is adjusted.
SHARPNESS
: The sharpness of the video image being projected is adjusted.
COLOR
: The color density of the video image being projected is adjusted.
TINT
: The tint of the video image being projected is adjusted. (Displayed only for NTSC signal)
ALL RESET
: All the items adjusted are reset.
OPTIONS
MENU AUTO OFF : Sets whether to turn off menu display automatically (YES) or not (NO).
LINE DISPLAY
: Sets whether to make the line display effective (ON) or not (OFF) for about 5 seconds after input
switching.
RIGHT LEFT REV. : Video image is reversed right-to-left.
TOP BOTTOM INV. : Video image is inverted top-to-bottom.
CLAMP
: Sets the clamp pulse's position at the back porch (BP) or on the sink tip (ST). Normally, the clamp
pulse is used at BP. If, with some PCs or workstations, the screen becomes unstable such as
being too dark or too bright, try to switch to ST.
RESIZE
: Does not work with AV (video) input. (RESIZE is shown in gray.)
BACK COLOR
: Specifies the background color when there is no video signal. Background color can be selected
from BLUE, CYAN, BLACK, GREEN, MAGENTA, RED, and YELLOW.
COLOR TEMP.
: Adjusts the color temperature of the image being projected. Make adjustment when the image
becomes reddish or bluish.
Color temperature can be set to LOW, MIDDLE, or HIGH.
ASPECT CHANGE : Selects the vertical-to-horizontal ratio of the image projected. The factory-set ratio is 4 : 3. When
projecting high-vision video image, a ratio of 16 : 9 can be selected.
SLEEP TIME
: Sets the length of sleep time. A set sleep time after input signal is depleted, the projector goes into
a stand-by state. Sleep time can be selected from 10 minutes, 20 minutes, 30 minutes, 60 minutes
and 0 minutes. (If you select 0 minutes, the sleep time will be cleared.)
LAMP TIME
: Indicates the accumulated used hours of the light-source lamp.
SOURCE
: Normally used in AUTO. If use in AUTO is unstable such as color not appearing, the screen being disturbed or the
screen being intermitted, set to the dedicated source (forced mode) in accordance with the input signal.
USER allows you to set a source which is uniquely adjusted by the user.
:
CHANNEL
Sets a line and multiple sources for each channel.
USER SOURCE
: Sets up an area for the source being input, and registers the user name.
SET UP
DISPLAY SIZE
: Adjusts H PIXEL, V PIXEL, H CENTER and V CENTER of video image.
DECODER
: Normally, set to AUTO. The color system of an input signal is automatically identified and shown in ( ). When use
in AUTO is unstable such as no color being shown, set the dedicated color system in accordance with the input
signal. You can select from AUTO, NTSC(480i), NTSC4.43, PAL, and SECAM.
LANGUAGE
: Text on the screen can be changed to a language other than English. Languages that can be displayed are the
following six :
(Japanese), ENGLISH, DEUTSCH (German), ESPAÑOL (Spanish), ITALIANO (Italian), and
FRANÇAIS (French). However, some text such as "QUICK ALIGNMENT", etc. are shown only in English.
For computer inputs, see the following page.
31
Advertisement
Table of Contents
