Select The Video Input To Be Projected; Adjust The Screen Size; Adjust Focus; For Operating Other Functions - JVC D-ILA DLA-M4000L Operating Instructions Manual

Basic Operations (Cont.)
Projector's buttons
AV button
Press the AV button or the RGB button to switch the
input.
• Each time you press either button, the selected input changes as
TEMP
LAMP EMERGENCY AV RGB SETTING QU
AL
RGB button
Remote control unit
LENS LOCKÔ UNLOCK
switch
QUICK
ALIGN. OPERATE
AV HIDE
PRESET PAGE BACK
AV button
AV RGB/COMPUTER
RGB button
+
U T
SHIFT ZOOM FOCUS
ZOOM (T/W) buttons
–
D W
LENS
Adjust the screen size with the remote control's ZOOM
(T/W) buttons.
When adjusting the screen size with the ZOOM buttons, set the
LENS LOCKÔUNLOCK switch to the UNLOCK position.
To enlarge the screen size:
Press the ZOOM (W) button.
To reduce the screen size:
Press the ZOOM (T) button.
ATTENTIONS
• DO NOT give any shock to this projector while
Notes
operating it; otherwise, the light-source lamp goes off
• The adjustment of the screen size (zoom adjustment) can also be made on
(the EMERGENCY indicator lights up).
the setting menu.
For operating the setting menu, refer to "Making Basic Settings" on page 30.
If the shock turns off the light-source lamp —
• When a fixed-focus lens is used, you cannot operate the setting menu.
Turn off the power by pressing the MAIN POWER
switch, then turn it on again. Then, when the
STAND BY indicator comes on, you can now
operate the projector as usual.
26

2. Select the video input to be projected

follows.
When you press VIDEO:
Y/C
VIDEO YPBPR
When you press COMPUTER:
RGB 1
RGB 2
Screen display
YPBPR
CH: 1
HDTV(1080i)
* When the input is switched, the line display and the source
display are shown on the upper part of the screen (they
disappear in about five seconds). However, they will not be
shown if LINE DISPLAY in "Setting and Adjusting Other
Functions (OPTIONS)" on page 41 is set to OFF.
(For setting the source, see page 44.)

3. Adjust the screen size

Remote control unit
+
FOCUS
–
Basic Operations (Cont.)
Projector's buttons
Adjust focus with the remote control's FOCUS (+/–)
buttons.
When adjusting the focus with the FOCUS buttons, set the LENS
LOCKÔUNLOCK switch to the UNLOCK position.
MERGENCY AV RGB SETTING QUICK
ALIGN.
QUICK ALIGN.
button
Note
• Focus adjustment can also be made on the setting menu. For operating the
setting menu, refer to "Making Basic Settings" on page 30.
To use the quick alignment function
Remote control unit
The quick alignment function is used to automatically adjust (set)
LENS LOCKÔ UNLOCK the screen settings of "TRACKING, PHASE, H. POS. and V. POS."
switch
of computer system input video.
• Use either the remote control's or projector's button.
QUICK ALIGN.
button
QUICK
ALIGN. OPERATE
AV HIDE
PRESET PAGE BACK
* During the automatic adjustment, "QUICK ALIGNMENT" appears
AV RGB/COMPUTER
+
U T
FOCUS (+/–)
SHIFT ZOOM FOCUS
buttons
–
D W
LENS
Note
• This function works only for computer system inputs.
CAUTION
• When performing automatic adjustment using the quick
alignment function:
Use a bright, still-picture screen. It may not function correctly on a
dark or motion-picture screen.
If the condition adjusted by using the quick alignment function is not
good, manually adjust TRACKING, PHASE, H. POS. and V. POS.
(see pages 30, 36 and 37).

4. Adjust focus

Remote control unit
+
FOCUS
–

For Operating Other Functions

When using the remote control unit:
Press the QUICK ALIGN. button.
When using the projector:
Clear the menu display, and press the projector's QUICK
ALIGN. " " and " " buttons at the same time.
on the screen and disappears automatically after the adjustment
is completed.
Remote control unit Projector
QUICK
ALIGN.
QUICK
ALIGN.
Screen display
Q U I C K A L I G N M E N T
27