BRP Ski-Doo REV-XS Series Operator's Manual
  1. Manuals
  2. Brands
  3. BRP Manuals
  4. Snowmobiles
  5. Ski-Doo REV-XS Series
  6. Operator's manual
BRP Ski-Doo REV-XS Series Operator's Manual

BRP Ski-Doo REV-XS Series Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2018
Read this guide thoroughly.
It contains important safety information.
Minimum recommended operator's age: 16 years old.
Keep this Operator's Guide in the vehicle.
5 2 0
0 0 1
7 9 5
Original Instructions

Advertisement

Table of Contents
loading

Related Manuals for BRP Ski-Doo REV-XS Series

Summary of Contents for BRP Ski-Doo REV-XS Series

  • Page 1 2018 Read this guide thoroughly. It contains important safety information. Minimum recommended operator’s age: 16 years old. Keep this Operator’s Guide in the vehicle. 5 2 0 0 0 1 7 9 5 Original Instructions...
  • Page 2 The KYB Pro series is a registered mark of KYB America LLC. 520001795 en KD/LG ®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates. ©2017 Bombardier Recreational Products Inc. and BRP US Inc. All rights reserved.

  • Page 3: Foreword

    Bombardier Recreational Products your new vehicle was prepared to your Inc. (BRP) warranty and a network of entire satisfaction. authorized Ski-Doo snowmobile deal- ers ready to provide the parts, service Know Before you Go or accessories you may require.

  • Page 4: Safety Messages

    NOTICE Indicates an instruction in this guide may occur. BRP reserves which, if not followed, could se- the right at any time to discontinue or verely damage vehicle components change specifications, designs, fea- or other property.

  • Page 5: Table Of Contents

    Effects of Having a Studded Track on the Life of the Snowmobile ..29 Installation of Studs on BRP Approved Tracks ....... . 29 Maintenance/Replacement .
  • Page 6 TABLE OF CONTENTS CONTROLS, INSTRUMENTS AND EQUIPMENT (cont’d) 7) Shift Lever (ACE and 1200 4-TEC Manual Shift) ......47 8) Multifunction Switch ............47 9) Seat Latch..
  • Page 7 TABLE OF CONTENTS BASIC PROCEDURES ............. . 91 Engine Starting Procedure ............ . 91 Emergency Starting (E-TEC).
  • Page 8 TABLE OF CONTENTS VEHICLE CARE ..............141 Post-Operation Care .
  • Page 9 TABLE OF CONTENTS CONTACT US (cont’d) Oceania ............... . 203 South America..
  • Page 10 TABLE OF CONTENTS _______________...

  • Page 11: Safety Information

    SAFETY INFORMATION ________ ________ SAFETY INFORMATION...

  • Page 12: General Precautions

    Do not make unauthorized modifica- tions, or use attachments or acces- To prevent serious injury or death from sories that are not approved by BRP. carbon monoxide: Since these changes have not been – Never run the vehicle in poorly ven-...

  • Page 13: Special Safety Messages

    – BRP recommends the operator has at least 16 years old of age. Verify also your local laws for age and training requirements.
  • Page 14 SPECIAL SAFETY MESSAGES – Know your local laws. Federal, state, provincial and local government agencies have enacted laws and regulations pertaining to the safe use and operation of snowmobiles. It is your responsibility as a snowmobiler to learn and obey these laws and regulations.
  • Page 15 – You may stud the track on this vehicle model. However, you MUST only use the BRP approved type stud for use on Ski-Doo snowmobiles. DO NOT EVER use conventional studs because the track thickness is thinner then our standard tracks.
  • Page 16 SPECIAL SAFETY MESSAGES – Make sure that you are able to achieve a stable stance, both feet resting posi- tively on the footboards of footrests with good grip, and that you are able to hold on firmly to the handholds. –...

  • Page 17: Active Technologies (Itc) (Ace And 1200 4-Tec)

    ACTIVE TECHNOLOGIES (iTC) (ACE AND 1200 4-TEC) Introduction Sport Mode NOTE: Some functions or features de- In sport mode, maximum engine scribed in this section may not apply to power is available throughout the en- every model, or may be available as an gine operational range.

  • Page 18: Riding The Vehicle

    RIDING THE VEHICLE Each operator has a responsibility to Before Starting the Engine ensure the safety of other recreation- 1. Remove snow and ice from body in- ists or bystanders. cluding lights, seat, footrests, con- You are responsible for proper opera- trols and instruments.
  • Page 19 RIDING THE VEHICLE NOTE: You may need to detach tether 3. Release parking brake. cord from your clothes to check lights. WARM UP 4. Refer to the section and In such a case, attach cord as soon follow instructions. as you get back at the controls of the snowmobile.

  • Page 20: How To Ride

    RIDING THE VEHICLE How to Ride Rider Position (Forward Operation) Your riding position and balance are Riding Gear the two basic principles of making your Proper snowmobile clothing should snowmobile go where you want it to. be worn. It should be comfortable When turning on the side of a hill, you and not too tight.

  • Page 21: Carrying A Passenger

    RIDING THE VEHICLE lowing the legs to absorb the shocks when traveling over uneven terrain. Avoid abrupt stops. mmo2008-003-004 Rider Position (Reverse Operation) We recommend sitting on your snow- mobile when operating in reverse. mmo2008-003-002 Avoid standing up. Your weight could Kneeling shift forward against throttle lever This position is achieved by placing...

  • Page 22: Terrain/Riding Variations

    – If the passenger feels uncom- gers (with optional seat), if you have an fortable or insecure for any rea- adult and a child for passenger, BRP son, he must right away inform recommends that the child sits in the the operator to slowdown or center location.
  • Page 23 RIDING THE VEHICLE ing position. Feet should be under the nature of ice is foreign to good con- body assuming a crouched position to trol of a snowmobile or any vehicle. absorb any jarring effect. On longer Traction for starting, turning or stop- stretches of “washboard”...
  • Page 24 RIDING THE VEHICLE Downhill You should always carry a snow shovel, probe and avalanche beacon while rid- Downhill driving requires that you have ing on mountains. We recommend full control of your vehicle at all times. that all mountain riders take a lo- On steeper hills, keep your center of cal avalanche safety training course gravity low and both hands on the han-...
  • Page 25 RIDING THE VEHICLE Bright Sunshine ahead. Apply partial throttle and brace yourself for the impact. Knees must Bright sunny days can considerably be flexed to act as shock absorbers. reduce your vision. The glare from sun and snow may blind you to the ex- Turning tent that you cannot easily distinguish ravines, ditches or other obstacles.

  • Page 26: Environment

    RIDING THE VEHICLE rear of the vehicle. Remember, your It is always IMPORTANT to keep a snowmobile is not designed to oper- safe distance between each snowmo- ate on bare pavement and steering on bile. Always maintain a safe interval this type of surface is more difficult.
  • Page 27 Help us lead it down biling fun! It simply means tread with the right path! From all of us at BRP, respect! thank you for doing your share. The fundamental objective of Light...
  • Page 28 RIDING THE VEHICLE areas where people can snowmobile safely and responsibly. This effort con- tinues today, as strong as ever. Respecting the areas where we ride... wherever they may be... is the only way to ensure their future enjoyment. That's one major reason why we know you'll agree that Light Treading is smart sledding! And there are more.

  • Page 29: Traction Enhancing Products

    BRP for special studs installation. Manoeuvrability WARNING Using traction enhancing products such as, more aggressive ski carbide...

  • Page 30: Acceleration

    TRACTION ENHANCING PRODUCTS Understeering WARNING In certain conditions, the use of studs To prevent surprises that could on the track could make the snowmo- lead to a loss of control of the bile prone to understeering if the skis snowmobile: are not equipped with more aggressive –...

  • Page 31: Effects Of Having A Studded Track On The Life Of The Snowmobile

    If tunnel protectors are excessively To ensure safe and proper installation, worn or not installed, the gas tank BRP recommends to have the studs in- could be punctured, causing a fire. stalled by your dealer. – Use only the BRP approved special studs.

  • Page 32: Maintenance/Replacement

    TRACTION ENHANCING PRODUCTS Maintenance/Replacement WARNING PROCEED WITH A VISUAL INSPEC- – See an authorized Ski-Doo TION OF YOUR TRACK BEFORE dealer for current specific stud- EACH USE. ding availability and applica- Look for any defects, such as: tions. – Perforations in the track –...

  • Page 33: Important On-Product Labels

    IMPORTANT ON-PRODUCT LABELS Hang Tag(s) 704901107 vmo2006-005-009_en TYPICAL . Operating, servicing and WARNING maintaining an off-road vehicle can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm.

  • Page 34: Vehicle Safety Labels

    IMPORTANT ON-PRODUCT LABELS Vehicle Safety Labels These labels are affixed to the vehicle for the safety of the operator, passenger or bystanders. The following labels are on your vehicle and they should be considered permanent parts of the vehicle. If missing or damaged, the decals can be replaced free of charge.
  • Page 35 IMPORTANT ON-PRODUCT LABELS 516005175B LABEL 4 - APPLICABLE MODELS mmo2008-003-069_a TYPICAL NEVER SIT IN CARGO AREA. Exceeding maximum cargo load may affect steering control and braking ability. MAXIMUM cargo load : (including tongue weight) 15,8 Kg / 35 Lbs. 516005058 516005280 516005058 LABEL 1...
  • Page 36 IMPORTANT ON-PRODUCT LABELS CAPACITOR Capacitor May Spark If Shorted. -Spark can ignite fuel vapors. -Keep objects away from poles. -When removing from vehicle, always discharge properly. EN-516008155-DEC LABEL 7 - E-TEC ONLY 516005509 LABEL 8 Always electrically disconnect both fuel injectors prior to testing for ignition spark.
  • Page 37 IMPORTANT ON-PRODUCT LABELS 516005055B 516005056B LABEL 10 LABEL 11 516005226 LABEL 12 - EUROPEAN MODELS 516004568 516004568 LABEL 13 ________ ________ SAFETY INFORMATION...
  • Page 38 - Check oil level using the dipstick. - The engine of this snowmobile has been developed and validated using the BRP XPS Synthetic 4-stroke oil ( 293 600 112 ). BRP recommends the use of its XPS approved lubricant or equivalent.

  • Page 39: Compliance Labels

    IMPORTANT ON-PRODUCT LABELS Compliance Labels EPA Compliance Label EMISSION CONTROL INFORMATION THIS VEHICLE IS CERTIFIED TO OPERATE ON UNLEADED GASOLINE AND MEETS U.S. XXXX EPA REGULATIONS FOR SNOWMOBILE SI ENGINES. ENGINE FAMILY FAMILLE DE MOTEUR XXXXXXXXXXXX PERMEATION FAMILY FAMILLE DE PERMÉATION XXXXXXXXXXXX XX g/kW-hr HC LIMITE DES ÉMISSIONS...

  • Page 40: Technical Information Labels

    D'ESSAIS INDÉPENDANT PENDENT TESTING LABOR- ET SATISFAIT TOUTES LES ATORY AND IT MEETS ALL engine may not be covered by the BRP limited warranty. NORMES DE SÉCURITÉ DU SSCC SAFETY STANDARDS SSCC EN VIGUEUR À LA IN EFFECT ON THE DATE OF See the operator’...
  • Page 41 IMPORTANT ON-PRODUCT LABELS OCTANE 516005507 LABEL 4 - NEAR DRIVE PULLEY - 800R E-TEC mmo2013-002-003 LOCATED ON FUEL CAP - ON 1200 4-TEC AND ACE ENGINES - IN COUNTRIES USING PUMP POSTED AKI (RON+MON)/2 OCTANE RATINGS OCTANE mmo2013-002-002 LOCATED ON FUEL CAP - ON E-TEC ENGINES - IN COUNTRIES USING PUMP POSTED AKI (RON+MON)/2 OCTANE RATINGS...
  • Page 42 IMPORTANT ON-PRODUCT LABELS This page is intentionally blank _______ ________ SAFETY INFORMATION...

  • Page 43: Vehicle Information

    VEHICLE INFORMATION _______________...

  • Page 44: Controls, Instruments And Equipment

    CONTROLS, INSTRUMENTS AND EQUIPMENT NOTE: Some features may not apply to your model or could be optional. NOTE: Some vehicle safety labels are not shown on illustrations. For information VEHICLE SAFETY LABELS on vehicle safety labels, refer to subsection. 520001653-101_a TYPICAL - GRAND TOURING SHOWN mmo2016-003-102_b TYPICAL - RENEGADE ENDURO SHOWN...

  • Page 45: Handlebar

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2016-003-100_b TYPICAL - GRAND TOURING SE SHOWN mmo2008-003-069_r mmo2008-008-011_b SOME EUROPEAN MODELS TYPICAL 1. Throttle lever 1) Handlebar 2. To accelerate 3. To decelerate The handlebar controls the steering of the snowmobile. As the handlebar WARNING is rotated to right or left, the skis are turned right or left to steer the snow- Test the throttle lever operation...

  • Page 46: Brake Lever

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2015-008-103_a mmo2015-008-100_a TYPICAL IF WANTED, CONTINUE TO ROTATE THE THROTTLE HOUSING WARNING Test the throttle lever operation each time before starting the en- gine. The lever must return to its the rest position once released. Otherwise, do not start engine. Switching from Thumb to Finger Throttle Position CAUTION It is highly recom-...

  • Page 47: Parking Brake Lever

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2014-004-001_a mmo2009-005-006_a TYPICAL 1. Brake lever TYPICAL — ENGAGE MECHANISM 2. To apply brake Step 1: Apply and hold brake Step 2: Lock brake lever using parking brake lever 4) Parking Brake Lever Parking brake lever is located on the LH To Release Parking Brake side of handlebar.

  • Page 48: Emergency Engine Stop Switch

    CONTROLS, INSTRUMENTS AND EQUIPMENT D.E.S.S. (Digitally Encoded Security The Ski-Doo learning key, limits the System) speed of the snowmobile and the en- gine torque, therefore enabling first The tether cord cap has an integrated time users and less experienced op- D.E.S.S.

  • Page 49: Shift Lever (Ace And 1200 4-Tec Manual Shift)

    CONTROLS, INSTRUMENTS AND EQUIPMENT 520001653-001_a 1. Reverse shift lever mmo2016-008-201_a ON POSITION All operators of the snowmobile should familiarize themselves with the function of the emergency engine stop switch by using it several times on first outing and whenever stopping the en- gine thereafter.
  • Page 50 CONTROLS, INSTRUMENTS AND EQUIPMENT Start/Electronic Reverse Button On electric start models, press to start ENGINE STARTING engine. Refer to PROCEDURE BASIC PROCE- in the DURES subsection. E E E E l l l l e e e e c c c c t t t t r r r r o o o o n n n n i i i i c c c c R R R R e e e e v v v v e e e e r r r r s s s s e e e e M M M M o o o o d d d d e e e e l l l l s s s s Once engine is started, press to en- gage the electronic reverse.
  • Page 51 CONTROLS, INSTRUMENTS AND EQUIPMENT 1 1 1 1 2 2 2 2 0 0 0 0 0 0 0 0 4 4 4 4 - - - - T T T T E E E E C C C C Heated grips will be in OFF position when there are no bars displayed on NOTE: Heated...
  • Page 52 CONTROLS, INSTRUMENTS AND EQUIPMENT NOTE: The heating intensity is dis- played via the multifunction display with the activation of the throttle lever switch. There are nine intensity set- tings. When released, display will re- turn to fuel tank level. mmo2013-004-040_a HEATING INTENSITY DISPLAY 1.

  • Page 53: Seat Latch

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-071_c 1. Seat latch mmo2014-004-001_f Pull and hold seat latch, then, pull seat MULTIFUNCTION GAUGE with a rearward movement. 1. MODE function 2. SET function NOTE: On models with a heated seat, disconnect the electrical connector lo- 9) Seat Latch cated underneath the seat.

  • Page 54: 10) Tool Kit

    CONTROLS, INSTRUMENTS AND EQUIPMENT NOTICE Make sure tools are se- cured properly to avoid contact with CVT (continuously variable transmission). The driven pulley expander is inserted through the starter clip. mmo2013-004-019_b TYPICAL Step 1: Position seat in place Step 2: Push seat forward until it latches NOTE: A distinctive snap will be felt.

  • Page 55: Analog/Digital Gauge (Mx Z Tnt, Mx Z Sport, Renegade Adrenaline, Renegade Sport, Grand Touring Sport And Expedition Sport)

    CONTROLS, INSTRUMENTS AND EQUIPMENT Gauge Description mmo2013-004-022_a TYPICAL - FRONT mmo2013-004-041_a 1. Front bumper ANALOG/DIGITAL GAUGE (STANDARD) 1. Speedometer 2. Tachometer (RPM) 3. Gauge digital display 4. Pilot lamps 5. Gauge SET (S) button NOTE: The gauge is factory preset in Imperial units but it is possible to change it to metric units, contact an authorized Ski-Doo dealer for unit set-...
  • Page 56 CONTROLS, INSTRUMENTS AND EQUIPMENT 4) Pilot Lamps and Messages mmo2013-004-042_a TYPICAL — PILOT LAMPS mmo2013-004-043 RH PORTION OF GAUGE 3) Digital Display mmo2013-004-041_b 1. Digital display The multifunction display is used to: – Display the WELCOME message on power up –...
  • Page 57 CONTROLS, INSTRUMENTS AND EQUIPMENT MONITORING SYS- See table below for usual pilot lamps information. Refer to for details on malfunction pilot lamps. PILOT LAMP(S) BEEPER DESCRIPTION 4 short E-TEC: Injection oil level is low. Stop vehicle in a safe beeps every place then, replenish injection oil reservoir.
  • Page 58 CONTROLS, INSTRUMENTS AND EQUIPMENT Gauge Features GAUGE FEATURES FUNCTIONS A) Odometer B) Trip meter “A” or “B” C) Trip hour meter D) Fuel level E) Engine coolant temperature F) Engine storage mode G) Heated grips heating intensity H) Heated throttle Lever heating intensity X = An X indicates a standard feature Opt = Feature available as an option (1) Coolant temperature is an option package.
  • Page 59 CONTROLS, INSTRUMENTS AND EQUIPMENT C) Trip Hour Meter E) Engine Coolant Temperature (Optional Module) Records vehicle running time when the electrical system is activated since The engine temperture level is dis- it has been reset. played via the digital display. Press the SET (S) button to select trip NOTICE If engine overheats, stop...

  • Page 60: Expedition Sport)

    CONTROLS, INSTRUMENTS AND EQUIPMENT H) Heated Throttle Lever Heating Gauge Description Intensity NOTE: The heating intensity is dis- played via the digital display with the activation of the throttle lever switch. When released, display will return to fuel tank level. NOTE: There are nine intensity set- tings.
  • Page 61 CONTROLS, INSTRUMENTS AND EQUIPMENT 4) Pilot Lamps and Messages mmo2013-004-045_b TYPICAL — PILOT LAMPS mmo2008-007-018 RH PORTION OF GAUGE 3) Multifunction Digital Display mmo2007-009-066_u MULTIFUNCTION ANALOG/DIGITAL GAUGE 1. Multifunction display The multifunction display is used to: – Display the WELCOME message on power up –...
  • Page 62 CONTROLS, INSTRUMENTS AND EQUIPMENT MONITORING SYS- See table below for usual pilot lamps information. Refer to for details on malfunction pilot lamps. PILOT LAMP(S) BEEPER MESSAGE DISPLAY DESCRIPTION 4 short beeps E-TEC: Injection oil level is low. Stop vehicle in a safe LOW OIL every place then, replenish injection oil reservoir.
  • Page 63 CONTROLS, INSTRUMENTS AND EQUIPMENT Gauge Features GAUGE FEATURES FUNCTIONS Indication by default A) Speedometer B) Engine RPM C) Odometer D) Trip meter “A” or “B” E) Trip hour meter F) Clock G) Fuel level H) Altitude (E-TEC) I) Top speed J) Average speed K) Heated grips heating intensity L) Heated throttle lever heating intensity...
  • Page 64 CONTROLS, INSTRUMENTS AND EQUIPMENT A) Speedometer Press the MODE (M) button to confirm selection or wait 5 seconds. addition analog type speedometer, vehicle speed can also be displayed via the multifunction display. Vehicle speed can be displayed on dis- play 1 or display 2. mmo2007-009-066_o B) Tachometer (RPM) In addition of the analog type tachome-...

  • Page 65: C) Odometer

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_n mmo2007-009-066_p 1. RPM mode 1. Trip meter (TRIP A/TRIP B) mode Press the MODE (M) button to confirm Press and hold the SET (S) button to re- selection or wait 5 seconds. set. NOTE: On ACE models, resetting TRIP B mode will also reset TOTAL FUEL CONSUMPTION.

  • Page 66: F) Clock

    CONTROLS, INSTRUMENTS AND EQUIPMENT To change MINUTES, while the value of HOURS is blinking, press the MODE (M) button to switch to minutes. Use the SET (S) button to change minutes. Press the MODE (M) button to save clock set-up and exit mode. G) Fuel Level Bar gauge that continuously indicates mmo2007-009-066_k...

  • Page 67: I) Top Speed

    CONTROLS, INSTRUMENTS AND EQUIPMENT While display is flashing, press the SET (S) button to select altitude mode. mmo2007-009-066_m While display flashes, press the SET (S) button to select top speed (TOP_SPD) mode. mmo2007-009-066_k The following symbol appears when al- titude mode is selected. mmo2008-003-023 ALTITUDE MODE mmo2007-009-066_n...

  • Page 68: J) Average Speed

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_m mmo2007-009-066_n 1. Vehicle average speed (AVR_SPD) mode While display flashes, press and hold the SET (S) button within 5 seconds to Press the MODE (M) button to confirm reset. selection or wait 5 seconds. mmo2007-009-066_w mmo2007-009-066_o J) Average Speed To reset, press the MODE (M) to select...

  • Page 69: K) Heated Grips Heating Intensity

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_w K) Heated Grips Heating Intensity mmo2007-009-044_a HEATED THROTTLE LEVER Bar gauge that indicates heating inten- 1. Operating range sity. M) Instant Fuel Consumption NOTE: There are nine intensity set- tings. When released, display will re- Calculates vehicle average fuel con- turn to engine coolant temperature (if sumption while riding.

  • Page 70: N) Total Fuel Consumption

    CONTROLS, INSTRUMENTS AND EQUIPMENT Press the MODE (M) button to confirm TC appears when the mode is se- selection or wait 5 seconds. lected. mmo2008-003-021_a TYPICAL mmo2007-009-066_o Press the MODE (M) button to confirm N) Total Fuel Consumption selection or wait 5 seconds. Records vehicle average fuel con- sumption since it has been reset.

  • Page 71: O) Message Display

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2012-006-902_a mmo2007-009-066_w Q) E-TEC Engine Storage Mode O) Message Display Displays OIL when the storage mode procedure is initiated. R) Lap Record Mode (Option) With this mode, vehicle speed, engine revolutions per minute (RPM) and a preselected function in display 1 can be recorded at the same time during a period of time defined by the operator.
  • Page 72 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2009-009-002_a 1. Record mode mmo2009-009-003_a 2. Odometer RECORD MODE 1. Recording time 3. Press the SET (S) button to scroll be- 2. Lap/session tween modes. 3. Selected mode Available modes are: STOP, REC To record another session, press the (record) or PLAY.

  • Page 73: S) Top Rpm (E-Tec)

    CONTROLS, INSTRUMENTS AND EQUIPMENT NOTE: Pressing the SET (S) button will stop time of the lap in progress, then the display will show the recorded time length of that lap and will switch auto- matically to the following recorded lap after 5 seconds.

  • Page 74: 14) Storage Compartment

    CONTROLS, INSTRUMENTS AND EQUIPMENT To change HOURS, while the value of HOURS is blinking, use the SET (S) but- ton to change hours. To change MINUTES, while the value of HOURS is blinking, press the MODE (M) button to switch to minutes. Use the SET (S) button to change minutes.

  • Page 75: Front Storage Compartment

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2013-004-017_a 1. Tab mmo2013-003-001_a 2. Storage compartment 1. Storage compartment 2. Latch 16) Hitch (Europe only) Push left hand side of cover back up Use this hitch in conjunction with a tow first then push back right hand side of bar to tow an accessory.

  • Page 76: 17) Drive Belt Guard

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2010-009-004_a mmo2010-009-006_a TYPICAL HITCH NOT IN USE 1. Rod 1. Hitch 2. Hairpin Secure rod to hitch using hairpin previ- 3. Support ously removed. 17) Drive Belt Guard Drive Belt Guard Removal WARNING NEVER operate engine: –...

  • Page 77: 18) Spare Drive Belt Holder

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2009-003-011_a TYPICAL 1. Retaining rod mmo2013-003-003_a Position rear portion of the belt guard 1. Retaining pin over the retainer and secure it using the retaining pin. Lift rear portion of guard then release from front tab by pivoting the guard NOTE: Make sure rear portion of the outwards.

  • Page 78: Upper Body Module (Hood)

    CONTROLS, INSTRUMENTS AND EQUIPMENT mbl2012-008-002_a 1. Headlights connector 4. Open LH side panel. 5. Remove LH and RH side panels. 6. Remove the drive belt guard. mmo2012-005-907_a 7. Disconnect the air intake connector 1. Spare drive belt tube. 2. Drive belt guard 3.
  • Page 79 CONTROLS, INSTRUMENTS AND EQUIPMENT 10. Disconnect the APS hose at the ECM. mbl2012-008-006_a SLIDE TOWARDS FRONT Upper Body Module Installation mbl2012-008-004_a 1. Insert the upper body module tabs 1. ECM 2. APS hose into the upper bottom pan open- ings. 11.

  • Page 80: 20) Side Panels

    CONTROLS, INSTRUMENTS AND EQUIPMENT To remove a side panel, open it then lift it up. Free the lower hinge from its slot, then free the upper hinge by lowering the panel. To install a side panel, insert the upper hinge and then the lower hinge. Close the side panel.

  • Page 81: Passenger Handhold (2-Up Models)

    CONTROLS, INSTRUMENTS AND EQUIPMENT 2. Raise or lower the handhold to suit passenger's comfort. mmo2009-005-014_a 3. Lift up the rear end of seat and gen- tly pull back just enough to expose mmo2009-005-009_a the accessories connector. Step 1: Pull knob Step 2: Adjust height NOTICE Do not stretch the acces-...

  • Page 82: Adjustable Mirrors (If Applicable)

    CONTROLS, INSTRUMENTS AND EQUIPMENT The tunnel bag can also be used as a back pack. The shoulder strap are hid- den in a pouch. WARNING Tunnel bag must be properly latched and must not contain any sharp, heavy or breakable objects. CAUTION MAXIMUM load for mmo2009-005-011_a this bag is 2.27 kg (5 lb) evenly dis-...

  • Page 83: Eco/Standard/Sport Mode Switch (Ace And 1200 4-Tec)

    CONTROLS, INSTRUMENTS AND EQUIPMENT 2 2 2 2 - - - - U U U U P P P P M M M M o o o o d d d d e e e e l l l l s s s s In the seat storage compartment.

  • Page 84: Passenger Heated Grip Switch

    CONTROLS, INSTRUMENTS AND EQUIPMENT msi2009-029-012_b mmo2009-005-010_a Step 1: Insert tabs 1. Off Step 2: Push towards vehicle 2. Warm 3. Hot 32) Passenger Heated Grip Switch 33) Heated Seats Switches The switch is located on the LH pas- The front seat switch is located on the senger handhold.

  • Page 85: 34) Rear Rack

    CONTROLS, INSTRUMENTS AND EQUIPMENT 34) Rear Rack G G G G r r r r a a a a n n n n d d d d T T T T o o o o u u u u r r r r i i i i n n n n g g g g a a a a n n n n d d d d E E E E x x x x p p p p e e e e d d d d i i i i t t t t i i i i o o o o n n n n M M M M o o o o d d d d e e e e l l l l s s s s WARNING All objects in rear rack must be...

  • Page 86: Fuel

    FUEL Fuel Requirements MIN. FUEL ENGINE OCTANE TYPE NOTICE Always use fresh gaso- RATING line. Gasoline will oxidize; the re- 87 AKI 600 ACE sult is loss of octane, volatile com- (RON+MON)/2 900 ACE Fuel pounds, and the production of gum 1200 4-TEC 92 RON with...

  • Page 87: Vehicle Fueling Procedure

    FUEL Vehicle Fueling Procedure 4. Insert the spout into the filler neck. 5. Pour fuel slowly so that air can es- WARNING cape from the tank and prevent fuel flow back. Be careful not to spill – Fuel is flammable and explosive fuel.

  • Page 88: Injection Oil (E-Tec)

    1. Oil reservoir The engine of this snow- 2. 3/4 level mobile has been developed and val- 3. 1/2 level idated using the recommended BRP 4. 1/4 level XPS™ oil. BRP recommends the NOTICE use of its recommended XPS oil or Check level and refill ev- equivalent.

  • Page 89: Break-In Period

    BREAK-IN PERIOD Operation During Break-In – Avoid pulling a load. – Avoid high speed cruising. A break-in period of 10 operating hours or 500 km (300 mi) is required for the vehicle. After the break-in period, the vehicle should be inspected by an authorized Ski-Doo dealer, repair shop or person FIRST of your own choosing.

  • Page 90: Operating Modes (Ace And 1200 4-Tec)

    OPERATING MODES (ACE AND 1200 4-TEC) To increase power, press the switch WARNING upwards. To decrease power, press Whenever changing operating the switch downwards. mode, make sure to maintain situ- ational awareness while riding. ECO Mode (Fuel Economy Mode) When ECO mode is selected (fuel economy mode), vehicle torque and speed are limited whereby an optimal cruising speed is maintained in order...

  • Page 91: Learning Key Modes

    OPERATING MODES (ACE AND 1200 4-TEC) To activate Sport mode when in Stan- 2. Wait for the information center to dard mode, press top end of switch complete its self-test and display once. the key recognition message. To activate Sport mode when in ECO A A A A n n n n a a a a l l l l o o o o g g g g / / / / D D D D i i i i g g g g i i i i t t t t a a a a l l l l G G G G a a a a u u u u g g g g e e e e mode, press top end of switch twice.
  • Page 92 OPERATING MODES (ACE AND 1200 4-TEC) NOTE: Setting 1 is the lowest avail- able torque, while setting 3 is the high- est available torque for learning key. 6. After a few seconds, the setting is automatically confirmed and saved. NOTE: The key speed setting is appli- cable to any key of the same type used on a specific snowmobile.

  • Page 93: Basic Procedures

    BASIC PROCEDURES Engine Starting Procedure Emergency Starting (E-TEC) Procedure A A A A C C C C E E E E a a a a n n n n d d d d 1 1 1 1 2 2 2 2 0 0 0 0 0 0 0 0 4 4 4 4 - - - - T T T T E E E E C C C C M M M M o o o o d d d d e e e e l l l l s s s s 1.

  • Page 94: Vehicle Warm-Up

    BASIC PROCEDURES WARNING When starting the snowmobile in an emergency situation, using drive pulley, do not reinstall the belt guard and return slowly to have snowmobile repaired. Vehicle Warm-Up Before every ride, vehicle has to be mmo2008-005-009 warmed up as follows. Hook up clip on drive pulley.

  • Page 95: Engaging Reverse (Rer) (E-Tec)

    BASIC PROCEDURES WARNING WARNING Make sure tether cord cap is re- Engaging the reverse mode is moved before standing in front the done by depressing the RER vehicle, getting close to the track button when the engine is run- or rear suspension components. ning.

  • Page 96: Shutting Off The Engine

    BASIC PROCEDURES Reverse (Manual Shift Models) WARNING Always remove the tether cord cap Shifting in Reverse from engine cut-off switch when To engage reverse gear, proceed as fol- vehicle is not in operation in order lows: to prevent accidental engine start- 1.

  • Page 97: Riding Conditions And Your Snowmobile

    T T T T r r r r a a a a c c c c k k k k P P P P r r r r o o o o f f f f i i i i l l l l e e e e o o o o f f f f 1 1 1 1 ..7 7 7 7 5 5 5 5 i i i i n n n n BRP does not recommend to ride a...

  • Page 98: Special Operation

    SPECIAL OPERATION Towing an Accessory Always use a rigid tow bar to tow an ac- cessory. Any towed accessory should have reflectors on both sides and at the rear. Check local laws for brake light(s) requirements. WARNING Never tow an accessory with a rope.

  • Page 99: Tune Your Ride

    TUNE YOUR RIDE Snowmobile handling and comfort de- are interrelated. It may be necessary pend upon multiple adjustments. to readjust center spring after adjust- ing front springs for instance. Test run the snowmobile under the same con- WARNING ditions; trail, speed, snow, operator Suspension adjustment could af- riding position, etc.

  • Page 100: Rear Suspension Adjustments

    TUNE YOUR RIDE PILOT TS SKI ADJUSTABILITY Possible Possible Position Lateral grip Handling understeering oversteering **** **** ***** ***** Rear Suspension Adjustments mmo2008-005-018_a TYPICAL SC-5U REAR SUSPENSION 1. Rear spring cams mmo2007-009-004_a 2. Center spring and shock absorber SC-5™ - ADJUSTABLE COMPONENTS 3.
  • Page 101 TUNE YOUR RIDE ACTION RESULT Lighter ski pressure under acceleration Increasing stopper More center strap length spring travel More bump absorption capability Heavier ski mmo2012-005-815_a pressure under MX Z X-RS - rMOTION - ADJUSTABLE acceleration COMPONENTS 1. Stopper strap Decreasing 2.
  • Page 102 TUNE YOUR RIDE mmo2015-007-101_b STOPPER STRAP POSITION 2 (2ND HOLE) mmo2015-007-102_b 1. Free hole STOPPER STRAP POSITION 1 (1ST HOLE, 2. 2nd hole from end LONGEST) 3. Towards rear 4. Tip of strap touching strap axis 1. 1st hole from end 2.
  • Page 103 TUNE YOUR RIDE Center Spring Center spring preload has an effect on steering effort, handling and bump ab- sorption. Also, since center spring preload ad- justment puts more or less pressure on the front of the track, it has an ef- fect on the performance in deep snow.
  • Page 104 TUNE YOUR RIDE ACTION RESULT Firmer rear suspension Higher rear end Increasing preload More bump absorption capability mmo2010-003-015_a Heavier steering CAM TYPE - HPG™ SHOCK ABSORBER 1. Spring preload adjustment cam Softer rear 2. Decrease preload suspension 3. Increase preload Lower rear end Less bump absorption...
  • Page 105 TUNE YOUR RIDE WHAT TO DO 50 mm to 75 mm No adjustment (2 in to 3 in) required More than Adjusted too soft. 75 mm (3 in) Increase preload Less than Adjusted too firm. 50 mm (2 in) Decrease preload mmr2012-337-002_a NOTE: If the specification is unattain- TYPICAL —...
  • Page 106 TUNE YOUR RIDE ACTION RESULT Firmer rear suspension Higher rear end Increasing More bump absorption preload capability Heavier steering Softer rear suspension Lower rear end mmo2012-005-811_a Less bump absorption rMOTION WITHOUT QUICK ADJUST KNOB Decreasing capability - RH SIDE 1. Position 1 preload Lighter steering 2.
  • Page 107 TUNE YOUR RIDE Rear Suspension Extension Rear Shock Absorber Stabilizer Cam Rear Shock Compression Damping S S S S C C C C - - - - 5 5 5 5 U U U U O O O O n n n n l l l l y y y y (MX Z X, MX Z X-RS, and Renegade To change stabilizer cam setting, pull lock off, then turn cam.
  • Page 108 TUNE YOUR RIDE mmo2012-005-804_a mmo2012-005-808_a REAR SHOCK MOUNTING POSITION 1. Compression damping adjustment button 1. High performance position 2. Sport position r r r r M M M M o o o o t t t t i i i i o o o o n n n n W W W W i i i i t t t t h h h h Q Q Q Q u u u u i i i i c c c c k k k k A A A A d d d d j j j j u u u u s s s s t t t t K K K K n n n n o o o o b b b b Turn the right side knob to adjust the Center Shock Absorber (MX Z X-RS) shock compression speed.
  • Page 109 TUNE YOUR RIDE mmo2012-005-807_a mmo2012-005-806_a 1. Center shock compression damping COUPLING BLOCK - RIGHT SIDE VIEW adjustment knob (R - RIGHT EMBOSSED ON BLOCK) 1. Position 1 (minimum) 2. Position 2 Coupling Blocks 3. Position 3 4. Position 4 (maximum) Coupling blocks adjustment has an ef- 5.

  • Page 110: Front Suspension Adjustments

    TUNE YOUR RIDE 3. Depress the heated throttle lever When the spacer is installed inside the switch as shown to increase or de- ski leg, skis are set to the narrower crease air pressure. stance. When the spacer is installed outside the ski leg, skis are set to the wider stance.
  • Page 111 TUNE YOUR RIDE ACTION RESULT Firmer front suspension Higher front end More precise Increasing preload steering More bump absorption capability mmo2010-003-027_a Softer front CAM TYPE - HPG SHOCK ABSORBER 1. Decrease preload suspension 2. Increase preload 3. Spring preload adjustment cam Lower front end Decreasing Lighter steering...
  • Page 112 TUNE YOUR RIDE ACTION RESULT Increasing Firmer compression compression damping force damping Decreasing Softer compression compression damping force damping mmo2012-005-814_c To adjust, turn clockwise to increase 1. Rebound adjuster (knob or slot) compression damping force and coun- terclockwise to decrease compression damping force.

  • Page 113: Adjustment Tips According To Vehicle Behavior

    TUNE YOUR RIDE Adjustment Tips According to Vehicle Behavior PROBLEM CORRECTIVE MEASURES Check ski alignment. – Reduce front suspension spring preload. Front suspension darting – Increase center spring preload. – Reduce rear spring preload. Steering feels too heavy at steady –...

  • Page 114: Vehicle Transportation

    VEHICLE TRANSPORTATION Make sure that oil reservoir and fuel tank caps are properly installed. Tilt bed trailers can easily be equipped with a winch mechanism to afford ma- ximum safety in loading. Simple as it may seem, never drive your snowmo- bile onto a tilt bed trailer or any other kind of trailer or vehicle.
  • Page 115 MAINTENANCE ______________...

  • Page 116: First Inspection

    FIRST INSPECTION This vehicle should be serviced by an authorized Ski-Doo dealer, repair shop or per- son of your own choosing. The first inspection is very important and must not be neglected. NOTE: The first inspection is at the expense of the vehicle owner. Signature of the Authorized Ski-Doo dealer, Date of inspection repair shop, or person...

  • Page 117: Maintenance Schedule

    Ski-Doo dealer has an in-depth technical knowledge and tools to service the Ski-Doo snowmobile, the emission-related warranty is not conditioned on the use of an authorized Ski-Doo dealer or any other establishment with which BRP has a commercial relationship. For emission-related warranty claims, BRP is limiting...
  • Page 118 MAINTENANCE SCHEDULE EVERY 3 000 KM (2,000 MI) OR EVERY YEAR AT PRESEASON (WHICHEVER COMES FIRST) Adjust and align track Inspect rear suspension (including stopper straps and slider shoes) Lubricate rear suspension (lubricate whenever the vehicle is used in wet conditions (rain, puddles)) Inspect fuel lines and connections Inspect front suspension...

  • Page 119: Maintenance Procedures

    MAINTENANCE PROCEDURES Engine Coolant This section includes instructions for basic maintenance procedures. WARNING WARNING Never open coolant tank cap when Turn off the engine, remove tether engine is hot. cord cap and follow these mainte- nance procedures when perform- Engine Coolant level Verification ing maintenance.

  • Page 120: Engine Oil (Ace)

    7. Remove dipstick and check the mobile has been developed and val- oil level. Oil level should be be- idated using the recommended BRP tween the MIN. and MAX. marks as shown, add if necessary. XPS™ oil. BRP recommends the use of its recommended XPS oil or equivalent.
  • Page 121 MAINTENANCE PROCEDURES WARNING Wipe off any oil spills. Oil is highly flammable when heated. Engine Oil Replacement WARNING The engine oil can be very hot. Wait until engine oil is warm. mmo2014-004-012_a NOTICE Engine oil and oil filter 1. Drain plugs access cover must be replaced at the same time.

  • Page 122: Engine Oil (1200 4-Tec)

    The engine of this snow- mobile has been developed and validated using the recommended BRP XPS™ oil. BRP strongly rec- ommends the use of its recom- mended XPS oil at all times. Dam- ages caused by oil which is not suit- mmr2011-070-004_a 1.
  • Page 123 MAINTENANCE PROCEDURES NOTICE Operating engine Engine Oil Replacement with an improper oil level may se- verely damage engine. Wipe off any WARNING spillage. The engine oil can be very hot. Wait until engine oil is warm. Make sure the engine is at normal oper- ating temperature.
  • Page 124 MAINTENANCE PROCEDURES 9. Allow oil to drain completely. 10. Install NEW sealing washer and O-ring on oil drain plug. NOTICE Never sealing washer a second time. Always re- place with a new one. mmo2014-004-012_a TYPICAL 1. Drain plugs access cover mmr2009-111-005_a 1.

  • Page 125: Engine Oil Filter (Ace)

    MAINTENANCE PROCEDURES Engine Oil Filter (ACE) Engine Oil Filter Replacement Oil Filter Removal 1. Remove the RH side panel. 2. Clean oil filter area. 3. Remove: – Oil filter cover screws – Oil filter cover with O-ring mmr2011-070-008_a – Oil filter. 1.

  • Page 126: Exhaust System

    MAINTENANCE PROCEDURES – Oil filter cover with O-ring – Oil filter. mmr2009-111-008_a 1. Lubricate with engine oil 4. Install the oil filter cover. 5. Tighten oil filter cover screws to mmr2009-111-006_a specification. 1. Oil filter cover screws 2. Oil filter cover TIGHTENING TORQUE 3.

  • Page 127: Engine Stopper (E-Tec)

    MAINTENANCE PROCEDURES not required, it is recommended that an authorized Ski-Doo dealer performs spark plugs inspection or replacement. Engine Stopper (E-TEC) Engine Stopper Adjustment The engine stopper is located on the LH front engine support, in front of the drive pulley. mmo2010-009-001_a 1.

  • Page 128: Brake Fluid

    MAINTENANCE PROCEDURES mmo2010-009-007_b mmo2014-004-001_g TIGHTENING SEQUENCE TYPICAL 1. Brake fluid reservoir NOTICE Serious pulley damage can occur if the engine stopper and its screws are not properly installed. Brake Fluid Recommended Fluid Use only DOT 4 brake fluid from a sealed container.
  • Page 129 BRP strongly recommends the use of its XPS Synthetic chaincase oil at all times. Damages caused by oil which is not suitable for the chaincase will not be covered by the BRP limited war- ranty. Access to Chaincase mmo2011-003-017_a CON-...

  • Page 130: Drive Chain

    MAINTENANCE PROCEDURES A A A A C C C C E E E E a a a a n n n n d d d d 1 1 1 1 2 2 2 2 0 0 0 0 0 0 0 0 4 4 4 4 - - - - T T T T E E E E C C C C Drive Chain Adjustment EXHAUST 1.

  • Page 131: Drive Belt

    MAINTENANCE PROCEDURES Drive Belt Drive Belt Installation 1. If necessary, open the driven pul- Drive Belt Inspection DRIVE BELT REMOVAL ley, refer to Inspect belt for cracks, fraying or ab- above. normal wear (uneven wear, wear on 2. Slip the belt over the drive pulley, one side, missing cogs, cracked fab- then over the driven pulley.
  • Page 132 MAINTENANCE PROCEDURES 2. Remove drive belt guard. 3. Loosen the clamping bolt. mmo2012-006-905_a TYPICAL - PRELIMINARY SETTING 1. Lowest portion of cogs even with external surface of drive belt NOTE: Turning the ring counterclock- wise lowers the drive belt in the pulley. Turning the ring clockwise raises the mmo2011-003-010_a drive belt in the pulley.

  • Page 133: Drive Pulley (E-Tec)

    MAINTENANCE PROCEDURES If the vehicle creeps, lower the drive NOTE: Use precision digital tachome- belt height from the preliminary set- ter for engine RPM adjustment. ting. Repeat procedure until creeping NOTE: The adjustment has an effect stops. on high RPM only. Reverse Activation There are 6 positions numbered 1 to 6.

  • Page 134: Track

    Improper assembly or modifica- tions could cause the pulley to ex- If your snowmobile is equipped with plode violently under the stress a BRP approved studded track, PRO- generated by the high rotational CEED WITH A VISUAL INSPECTION speed. OF YOUR TRACK BEFORE EACH See your Ski-Doo dealer to main- USE.
  • Page 135 MAINTENANCE PROCEDURES On approved studded tracks, replace Track Tension Verification broken or damaged studs immediately. NOTE: Ride the snowmobile in snow If your track shows signs of deteriora- about 15 to 20 minutes prior to adjust- tion, it must be replaced immediately. ing track tension.
  • Page 136 MAINTENANCE PROCEDURES TRACK ADJUSTMENT SPECIFICATION Track deflection setting 30 mm - 35 mm All models (1-3/16 in - 1-3/8 in) except Expedition Track deflection 45 mm - 50 mm mmr2009-133-001_a setting (1-3/4 in - 1-31/32 in) Expedition Track load 6 kgf to 8.5 kgf reading (13 lbf to 19 lbf) 11.
  • Page 137 MAINTENANCE PROCEDURES Track Alignment WARNING Before checking track alignment, ensure that the track is free of all particles which could be thrown out while track is rotating. Keep hands, tools, feet and clothing clear of track. Always lift the snow- mobile on a wide-base stand with mmo2013-004-032_a a rear deflector panel.

  • Page 138: Suspension

    MAINTENANCE PROCEDURES 4. To correct track alignment: 4.1 Stop engine. 4.2 Remove tether cord cap from engine cut-off switch. WARNING Remove tether cord cap from engine cut-off switch before performing any maintenance mmo2013-004-032_a or adjustment, unless other- rMOTION wise specified. Vehicle must 1.

  • Page 139: Skis

    MAINTENANCE PROCEDURES Suspension Lubrication Lubricate the following suspension pivots at grease fittings using SUS- PENSION GREASE (P/N 293 550 033). MAINTENANCE SCHEDULE Refer to for maintenance frequency. mmo2010-007-026_a SC-5U 1. Grease fittings Steering and Front Suspension Condition Visually inspect steering and front sus- pension for tightness of components (steering arms, control arms and links, tie rods, ball joints, ski bolts, ski legs,...
  • Page 140 MAINTENANCE PROCEDURES E E E E l l l l e e e e c c c c t t t t r r r r i i i i c c c c S S S S t t t t a a a a r r r r t t t t A15E0KA 1.

  • Page 141: Lights

    MAINTENANCE PROCEDURES FUSE AND RELAY BOX DESCRIPTION DESCRIPTION RATING Electromechanical reverse 30 A (applicable models) Start button/Cooling 15 A fan/Clock Headlights/Taillight/ 20 A Brake light mmo2013-004-020_a ECM/Gauge/Caps 10 A 1. Rubber boots Fuses F1, NOTE: Make sure to properly reinstall Main relay F3 and F6 both rubber boots to ensure that no hu-...
  • Page 142 MAINTENANCE PROCEDURES mmo2013-004-036_c Step 1: Push both sides Step 2: Push down to release Step 3: Release both sides 1. Retaining clip 5. Pull bulb and replace. Properly rein- stall parts. Headlights Beam Aiming Open the front storage compartment. Turn knob to adjust beam height. Turn knob clockwise to lower the beam height.

  • Page 143: Vehicle Care

    To remove grease, oil and grime, use BRP HEAVY DUTY CLEANER (P/N 293 110 001). NOTICE Do not use Heavy duty cleaner on decals or vinyl.

  • Page 144: Storage

    STORAGE Engine Storage Mode During summer, or when a snowmo- bile is not in use for more than three (E-TEC) months, proper storage is necessary. Like other engines, the E-TEC has to be properly lubricated at storage for STORAGE internal parts protection. The E-TEC Clean the vehicle system offers a built-in engine storage lubrication function (summerization)
  • Page 145 STORAGE 5. Release all buttons when gauge dis- plays PUSH (S) appears. 6. Again, press and hold the SET (S) button for 2 - 3 seconds. NOTE: The gauge will display OIL when the storage procedure is initi- ated. 7. When gauge displays OIL, release button and wait for the lubrication function to end.
  • Page 146 STORAGE This page is intentionally blank ______________...

  • Page 147: Technical Information

    TECHNICAL INFORMATION ______________...

  • Page 148: Vehicle Identification

    VEHICLE IDENTIFICATION Vehicle Description Decal Vehicle Identification Number (VIN) Vehicle description decal is located on VIN is scribed on vehicle description right hand side of tunnel. decal. See above. It is also engraved on tunnel near vehicle description de- cal. Model number and model year are part of the information found in the VIN.
  • Page 149 VEHICLE IDENTIFICATION mmo2011-003-003_a 600 ACE ENGINE 1. Engine identification number mmo2014-004-007_a 900 ACE ENGINE 1. Engine identification number mmo2009-005-039_a 1200 4-TEC ENGINE 1. Engine identification number ______________...

  • Page 150: Noise Emission And Vibration Values (All Countries Except Canada/United States)

    NOISE EMISSION AND VIBRATION VALUES (ALL COUNTRIES EXCEPT CANADA/UNITED STATES) 600 HO MODEL 800R E-TEC 600 ACE 900 ACE 1200 4-TEC E-TEC NOISE EMISSION AND VIBRATION VALUES 96,7 dB @ 99,3 dB @ 90,4 dB @ 92,7 dB @ 98,1 dB @ Sound power 4050 RPM 3950 RPM...

  • Page 151: Ec Declaration Of Conformity

    The EC-Declaration of Conformity does not appear in this version of the Operator's Guide. Please refer to the printed version that was delivered with your vehicle. ddd2009-001...

  • Page 152: Epa Certified Engines

    EPA CERTIFIED ENGINES Engine Emissions EPA Emission Regulations Information All Ski-Doo snowmobiles manufac- tured by BRP are certified to the EPA Manufacturer's Responsibility as conforming to the requirements of the regulations for the control of air Beginning with 2007 model year en-...

  • Page 153: Radio Frequency Digitally Encoded Security System

    RADIO FREQUENCY DIGITALLY ENCODED SECURITY SYSTEM (RF D.E.S.S. KEY) This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

  • Page 154: Specifications

    SPECIFICATIONS 6 6 6 6 0 0 0 0 0 0 0 0 A A A A C C C C E E E E M M M M O O O O D D D D E E E E L L L L S S S S MODEL 600 ACE ENGINE...
  • Page 155 SPECIFICATIONS MODEL 600 ACE DRIVE SYSTEM (cont'd) Expedition Sport Renegade Sport Small sprocket number of Grand Touring teeth Sport MX Z Sport MX Z Sport Expedition Sport Large sprocket number of Renegade Sport teeth Grand Touring Sport Inside North America Drive sprocket number of teeth Europe MX Z Sport...
  • Page 156 SPECIFICATIONS MODEL 600 ACE SUSPENSION Front suspension Dual A-arms MX Z Sport Renegade Sport Grand Motion control Touring Sport Expedition Sport Front shock MX Z Sport (Europe) HPG Plus Renegade Sport (Europe) MX Z Sport Renegade Sport 229 mm (9 in) Grand Touring Front suspension max.
  • Page 157 SPECIFICATIONS MODEL 600 ACE ELECTRICAL SYSTEM Lightning system output 420/650 watts @ 6000 RPM Headlights bulb HI/LOW beam 2 x 60/55 watts (H-4) Taillight bulb 2.6 W / 139m W LED Type NGK MR7BI or equivalent Spark plug 0.8 mm (.031 in) FUSES MAINTENANCE Fuses and relays...
  • Page 158 SPECIFICATIONS 6 6 6 6 0 0 0 0 0 0 0 0 H H H H O O O O E E E E - - - - T T T T E E E E C C C C M M M M o o o o d d d d e e e e l l l l s s s s MODEL 600 HO E-TEC ENGINE...
  • Page 159 SPECIFICATIONS MODEL 600 HO E-TEC DRIVE SYSTEM (cont'd) Large sprocket number of teeth All except Grand Touring LE Drive sprocket number of teeth Grand Touring LE MX Z Track nominal width Renegade 38 cm (15 in) Grand Touring LE Renegade Renegade Adrenaline 348.7 cm (137 in) Renegade Enduro...
  • Page 160 SPECIFICATIONS MODEL 600 HO E-TEC SUSPENSION (cont'd) MXZ TNT MX Z Blizzard MX Z X Renegade Adrenaline 229 mm (9 in) Front suspension max. Renegade X travel Renegade Enduro Grand Touring LE MX Z X-RS 241 mm (9.5 in) Rear suspension rMotion Renegade Adrenaline Renegade Enduro...
  • Page 161 SPECIFICATIONS MODEL 600 HO E-TEC ELECTRICAL SYSTEM 12V/360 W Lightning system output 55 V/1100 W Headlights bulb HI/LOW beam 2 x 60/55 Watts (H-4) Taillight bulb 2.6 W / 139m W LED Type NGK PZFR6F or equivalent Spark plug 0.75 mm ± 0.05 mm (.03 in ± .002 in) (not adjustable) FUSES MAINTENANCE...
  • Page 162 SPECIFICATIONS MODEL 600 HO E-TEC DIMENSIONS AND WEIGHT (cont'd) MX Z TNT MX Z Blizzard MX Z X MX Z X-RS Ski stance 107.7 cm (42.4 in) Renegade Adrenaline Renegade X Renegade Enduro Grand Touring LE Ski overall length 106.6 cm (42 in) Ski width 145 mm (5.7 in) INJECTION OIL...
  • Page 163 SPECIFICATIONS 8 8 8 8 0 0 0 0 0 0 0 0 R R R R E E E E - - - - T T T T E E E E C C C C M M M M o o o o d d d d e e e e l l l l s s s s MODEL 800R E-TEC ENGINE...
  • Page 164 SPECIFICATIONS MODEL 800R E-TEC DRIVE SYSTEM (cont'd) Large sprocket number of teeth Drive sprocket number of teeth Track nominal width 38 cm (15 in) Track nominal length Renegade Enduro 348.7 cm (137 in) Track profile height 31.8 mm (1.25 in) Deflection 30 mm to 35 mm (1-3/16 in to 1-3/8 in) Track tension...
  • Page 165 SPECIFICATIONS MODEL 800R E-TEC ELECTRICAL SYSTEM 12V/360 W Lightning system output 60 V/1100 W Headlights bulb HI/LOW beam 2 x 60/55 Watts (H-4) Taillight bulb 2.6 W / 139m W LED Type NGK PFR7AB or equivalent Spark plug 0.75 mm ± 0.05 mm (.03 in ± .002 in) (not adjustable) FUSES MAINTENANCE...
  • Page 166 SPECIFICATIONS 9 9 9 9 0 0 0 0 0 0 0 0 A A A A C C C C E E E E M M M M o o o o d d d d e e e e l l l l s s s s MODEL 900 ACE ENGINE...
  • Page 167 SPECIFICATIONS MODEL 900 ACE ELECTRICAL SYSTEM (cont'd) FUSES MAINTENANCE Fuses and relays Refer to DRIVE SYSTEM Drive pulley type eDrive II Driven pulley type QRS (short shaft) Engagement 2200 RPM XPS SYNTHETIC CHAINCASE OIL Type (P/N 413 803 300) Chaincase oil Capacity 500 ml (16.9 U.S.
  • Page 168 SPECIFICATIONS MODEL 900 ACE DRIVE SYSTEM (cont'd) MX Z TNT 327 cm (129 in) MX Z Blizzard Renegade Adrenaline Track nominal length Renegade Enduro 348 cm (137 in) Grand Touring Expedition Sport 392 cm (154 in) MX Z TNT MX Z Blizzard Renegade Adrenaline 31.8 mm (1.25 in) Track profile height...
  • Page 169 SPECIFICATIONS MODEL 900 ACE SUSPENSION (cont'd) Expedition Sport 210 mm (8.3 in) MX Z TNT Front suspension max. MX Z Blizzard travel Renegade Adrenaline 229 mm (9 in) Renegade Enduro Grand Touring LE MX Z TNT MX Z Blizzard Renegade Adrenaline rMotion Rear suspension Renegade Enduro...
  • Page 170 SPECIFICATIONS MODEL 900 ACE WEIGHT AND DIMENSIONS (cont'd) Expedition Sport 332.9 cm (131.1 in) MX Z TNT 301 cm (118.5 in) MX Z Blizzard Vehicle overall length Grand Touring 322.6 cm (127 in) Renegade Adrenaline 311 cm (122.4 in) Renegade Enduro Expedition Sport 115.9 cm to 120.4 cm (45.6 in to 47.4 in) MX Z...
  • Page 171 SPECIFICATIONS 1 1 1 1 2 2 2 2 0 0 0 0 0 0 0 0 4 4 4 4 - - - - T T T T E E E E C C C C MODEL 1200 4-TEC ENGINE Rotax 1200, liquid cooled, 4-Stroke, Engine type...
  • Page 172 SPECIFICATIONS MODEL 1200 4-TEC DRIVE SYSTEM (cont'd) MX Z TNT MX Z Blizzard MX Z X Large sprocket number of teeth Renegade Adrenaline Renegade Enduro Renegade X Grand Touring MX Z TNT MX Z Blizzard MX Z X Renegade Adrenaline Drive sprocket number of teeth Renegade Enduro Renegade X...
  • Page 173 SPECIFICATIONS MODEL 1200 4-TEC SUSPENSION Front suspension RAS 2 Grand Touring SE MX Z X HPG Plus R Renegade X Front shock MX Z TNT MX Z Blizzard HPG Plus Renegade Adrenaline Renegade Enduro Front suspension max. travel 229 mm (9 in) Rear suspension rMotion Grand Touring LE...
  • Page 174 SPECIFICATIONS MODEL 1200 4-TEC ELECTRICAL SYSTEM (cont'd) Type NGK CR8EKB or equivalent Spark plug Not adjustable FUSES MAINTENANCE Fuses and relays Refer to WEIGHT AND DIMENSIONS MX Z TNT 231 kg (509 lb) Renegade X 235 kg (518 lb) Renegade Adrenaline 239 kg (528 lb) Renegade Enduro 246 kg (543 lb)
  • Page 175 175 mm (6.9 in) The engine of this snowmobile has been developed and validated using the recommended BRP XPS™ oil. BRP recommends the use of its recommended XPS oil or equivalent. Damages caused by oil which is not suitable for this 4-stroke engine may not be covered by the BRP limited warranty.
  • Page 176 SPECIFICATIONS This page is intentionally blank ______________...

  • Page 177: Troubleshooting

    TROUBLESHOOTING ______________...

  • Page 178: Troubleshooting Guidelines

    TROUBLESHOOTING GUIDELINES ELECTRIC STARTER DOES NOT WORK 1. Emergency engine stop switch in OFF position or tether cord cap not installed on engine cut-off switch. – Place the emergency engine stop switch in the ON position and install tether cord cap (on engine cut-off switch. 2.
  • Page 179 TROUBLESHOOTING GUIDELINES ENGINE LACKS ACCELERATION OR POWER (cont’d) 8. Drive belt worn too thin. – If the drive belt has lost more than 3 mm (1/8 in) of its original width, it will af- fect vehicle performance. – Replace drive belt. 9.
  • Page 180 TROUBLESHOOTING GUIDELINES NO RESPONSE FROM THE THROTTLE LEVER INPUTS. MESSAGE DISPLAYED: PRESS START TO GO 1. Engine management system has detected a sensor problem. – Press and hold the Start/electronic reverse button in order to move vehicle. Seek service from an authorized Ski-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement.

  • Page 181: Monitoring System

    MONITORING SYSTEM Pilot Lamps, Messages and Beeper Codes Gauge pilot lamp(s) will inform you if an anomaly occurs or to inform you of a particular condition. mmo2013-004-042_a TYPICAL — PILOT LAMPS Pilot lamp can flash alone or in combi- nation with another lamp. On the multifunction analog/digital gauge, the display is used as a comple- ment of the pilot lamps to give you a...
  • Page 182 MONITORING SYSTEM NOTE: Some of the listed pilot lamps and messages do not apply to all models. The message display is available only on the multifunction analog/digital gauge. PILOT MESSAGE LAMP(S) BEEPER DESCRIPTION DISPLAY ACE: Low engine oil pressure. Stop 4 short vehicle in a safe place then, check oil beeps every...
  • Page 183 MONITORING SYSTEM PILOT MESSAGE LAMP(S) BEEPER DESCRIPTION DISPLAY Engine detonation (RPM is limited when this condition occurs). – Ensure recommended fuel is used. 4 short – Check fuel quality, replace if — beeps every KNOCK necessary. 5 minutes – If fault still occurs, contact an authorized Ski-Doo dealer, repair shop, or person of your own choosing.

  • Page 184: Fault Codes

    MONITORING SYSTEM PILOT MESSAGE LAMP(S) BEEPER DESCRIPTION DISPLAY — — Fuel level sensor problem. (blinking) ACE and 1200 4-TEC: Throttle lever applied while attempting an engine start — — THROTTLE OPEN (engine cranks but won't run). Release throttle lever while starting. ACE: Throttle wide...

  • Page 185: Warranty

    WARRANTY ______________...

  • Page 186: Brp Limited Warranty Usa And Canada: 2018 Ski-Doo ® Snowmobiles

    BRP. BRP reserves the right to modify this limited warranty at any time, be- ing understood that such modification will not alter the warranty conditions appli- cable to the products sold while this warranty is in effect.
  • Page 187 BRP will not honor this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 188 The customer must cease using the snowmobile upon the appearance of an anom- aly. The customer must notify a servicing BRP dealer within three (3) days of the appearance of a defect, and provide it with reasonable access to the product and reasonable opportunity to repair it.
  • Page 189 We recommend discussing the issue with the authorized Ski-Doo Distribu- tor/Dealer's service manager or owner. If the matter still remains unresolved, contact BRP by filling out the customer con- tact form at www.brp.com or contact BRP by mail at one of the addresses listed CONTACT US under the section of this guide.

  • Page 190: Us Epa Emission-Related Warranty

    2. It is free from defects in materials and workmanship that may keep it from meeting the requirements of 40 CFR 1051 and 40 CFR 1060. Where a warrantable condition exists, BRP will repair or replace, as it elects, any part or component with a defect in materials or workmanship that would increase the engine’s emissions of any regulated pollutant within the stated warranty...
  • Page 191 Components Covered The emission-related warranty covers all components whose failure would in- crease an engine’s emissions of any regulated pollutant, including the following listed components: 1. For exhaust emissions, emission-related components include any engine parts related to the following systems: –...
  • Page 192 * In the USA, products are distributed and serviced by BRP US Inc. ______________...

  • Page 193: Brp International Limited Warranty: 2018 Ski-Doo ® Snowmobiles

    BRP. BRP reserves the right to modify this warranty at any time, being understood that such modification will not alter the warranty conditions applicable to the products sold while this warranty is in effect.
  • Page 194 – Damage resulting from removal of parts, improper repairs, service, main- tenance, modifications or use of parts or accessories not manufactured or approved by BRP which in its reasonable judgement are either incompatible with the product or adversely affect its operation, performance and durability, or resulting from repairs done by a person that is not an authorized servicing Ski-Doo Distributor/Dealer;...
  • Page 195 BRP will not honour this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 196 BRP reserves the right to improve or modify products from time to time without as- suming any obligation to modify products previously manufactured. 8) TRANSFER If the ownership of a product is transferred during the warranty coverage period, this limited warranty, subject to its terms and conditions, shall also be transferred...

  • Page 197: Brp Limited Warranty For The European And The

    BRP. BRP reserves the right to modify this warranty at any time, being understood that such modification will not alter the warranty conditions applicable to the products sold while this warranty is in effect.
  • Page 198 – Damage resulting from removal of parts, improper repairs, service, main- tenance, modifications or use of parts or accessories not manufactured or approved by BRP which in its reasonable judgement are either incompatible with the product or adversely affect its operation, performance and durability, or resulting from repairs done by a person that is not an authorized servicing Ski-Doo Distributor/Dealer;...
  • Page 199 BRP will not honour this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 200 We recommend discussing the issue with the authorized Ski-Doo Distribu- tor/Dealer's service manager or owner. If the matter still remains unresolved, contact BRP by filling out the customer con- tact form at www.brp.com or contact BRP by mail at one of the addresses listed CONTACT US under the section of this guide.
  • Page 201 ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be responsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished under its responsibility.
  • Page 202 This page is intentionally blank ______________...

  • Page 203: Customer Information

    CUSTOMER INFORMATION ______________...

  • Page 204: Privacy Information

    PRIVACY INFORMATION BRP wishes to inform you that your coordinates will be used for safety and war- ranty related purposes. Furthermore, BRP and its affiliates may use its customer list to distribute marketing and promotional information about BRP and related products.

  • Page 205: Contact Us

    CONTACT US South America www.brp.com Rua James Clerck Maxwell, 230 North America TechnoPark Campinas SP 13069-380 Brazil 565 de la Montagne Street Valcourt (Québec) J0E 2L0 Asia Canada Sturtevant, Wisconsin, U.S.A. 15/F Parale Mitsui Building,8 10101 Science Drive Higashida-Cho, Kawasaki-ku...
  • Page 206 In case of change of ownership, please join a proof that the former owner agreed to the transfer. Notifying BRP, even after the expiration of the limited warranty, is very important as it enables BRP to reach the Snowmobile owner if necessary, like when safety re- calls are initiated.
  • Page 207 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 208 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 209 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 210 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 211 GUIDE DU CONDUCTEUR, Séries REV-XS / ANGLAIS FAIT AU / MADE IN CANADA U/M:P.C. ®™ AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC. OR ITS AFFILIATES. ©2017 BOMBARDIER RECREATIONAL PRODUCTS INC. ALL RIGHTS RESERVED. PRINTED IN CANADA.

This manual is also suitable for:

Ski-doo 600 ho e-tec 2018Ski-doo 800r e-tec 2018Ski-doo 600 ace 2018Ski-doo 900 ace 2018Ski-doo 1200 4-tec 2018

Table of Contents