BRP LYNX XU 600 R E-TEC Operator's Manual
  1. Manuals
  2. Brands
  3. BRP Manuals
  4. Snowmobiles
  5. LYNX XU 600 R E-TEC
  6. Operator's manual

BRP LYNX XU 600 R E-TEC Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2017
2017
OPERATOR´S GUIDE
XU
®
600/800 R E-TEC
®
1200 4-TEC
900 ACE
™
Read this guide thoroughly. It contains important
safety information.
Minimum recommended operator's age: 16 years old.
Keep this Operator's Guide in the vehicle.
EN 619 950 592
Original instructions

Advertisement

Table of Contents
loading

Related Manuals for BRP LYNX XU 600 R E-TEC

Summary of Contents for BRP LYNX XU 600 R E-TEC

  • Page 1 2017 2017 OPERATOR´S GUIDE ® 600/800 R E-TEC ® 1200 4-TEC 900 ACE ™ Read this guide thoroughly. It contains important safety information. Minimum recommended operator’s age: 16 years old. Keep this Operator’s Guide in the vehicle. EN 619 950 592 Original instructions...
  • Page 2 ® Lynx D.E.S.S.™ HPG™ XU™ TRA™ ROTAX ® PPS™ ® 619950592 en ®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates. ©2016 Bombardier Recreational Products Inc. and BRP US Inc. All rights reserved.

  • Page 3: Foreword

    Bombardier Recreational Products injured or killed, read the following sec- Inc. (BRP) warranty and a network of tions before you operate the vehicle: authorized Lynx snowmobile dealers SAFETY INFORMATION –...

  • Page 4: Safety Messages

    BRP reserves the right at any time to discontinue or The safety alert symbol indicates a change specifications, designs, fea- potential injury hazard.

  • Page 5: Table Of Contents

    Installation of Studs on BRP Approved Tracks ....... . 26...
  • Page 6 TABLE OF CONTENTS CONTROLS, INSTRUMENTS AND EQUIPMENT (cont’d) 8) Gearshift Lever ............. . . 44 9) Adjustable Mirrors.
  • Page 7 TABLE OF CONTENTS OPERATING INSTRUCTIONS........... . . 75 Engine Starting Procedure .
  • Page 8 How to Read Fault Codes ........... . 146 WARRANTY BRP FINLAND OY INTERNATIONAL LIMITED WARRANTY: 2017 LYNX ®...

  • Page 9: Safety Information

    SAFETY INFORMATION ________ ________ SAFETY INFORMATION...

  • Page 10: General Precautions

    Do not make unauthorized modifica- tions, or use attachments or acces- To prevent serious injury or death from sories that are not approved by BRP. carbon monoxide: Since these changes have not been – Never run the vehicle in poorly ven-...

  • Page 11: Special Safety Messages

    – BRP recommends the operator has at least 16 years old of age. – It is very important to inform any operator, regardless of his experience, of the handling characteristics of this snowmobile.
  • Page 12 SPECIAL SAFETY MESSAGES – Speeding can be fatal. In many cases, you cannot react or respond quickly enough to the unexpected. Always ride at a speed which is suitable to the trail, weather conditions and your own ability. Know your local rules. Speed limit may be in effect and meant to be observed.
  • Page 13 – You may stud the track on this vehicle model. However, you MUST only use the BRP approved type stud for use on Lynx snowmobiles. DO NOT EVER use con- ventional studs, the track thickness is thinner compared to some other tracks.

  • Page 14: Active Technologies (Itc) (900 Ace And 1200 4-Tec)

    ACTIVE TECHNOLOGIES (iTC) (900 ACE AND 1200 4-TEC) Introduction Sport Mode NOTE: Some functions or features de- In sport mode, maximum engine scribed in this section may not apply to power is available throughout the en- every model, or may be available as an gine operational range.

  • Page 15: Riding The Vehicle

    RIDING THE VEHICLE Each operator has a responsibility to Before Starting the Engine ensure the safety of other recreation- 1. Remove snow and ice from body in- ists or bystanders. cluding lights, seat, footrests, con- You are responsible for proper opera- trols and instruments.
  • Page 16 RIDING THE VEHICLE WARM UP 2. Check the engine cut-off switch (by 4. Refer to the section and pulling tether cord cap) and emer- follow instructions. gency engine stop switch opera- tion. Pre-Ride Check List 3. Release parking brake. ✔ ITEM OPERATION Body including seat, footrests,...

  • Page 17: How To Ride

    RIDING THE VEHICLE How to Ride First aid kit Provided tool kit Mobile phone Knife Riding Gear Proper snowmobile clothing should Spare spark plugs Flashlight be worn. It should be comfortable Friction tape Trail map and not too tight. Always check the weather forecast before going on a Spare drive belt Snack...
  • Page 18 RIDING THE VEHICLE Sitting Feet on the running boards, body mid- way back on seat is an ideal position when operating the snowmobile over familiar, smooth terrain. Knees and hips should remain flexible to absorb shocks. fmo2008-003-003 Standing Place both feet on the running boards. Knees should be flexed to absorb the shock from surface bumps.

  • Page 19: Carrying A Passenger

    BRP recommends that the the vehicle. In addition, “body eng- child sits in the center location. This lish”...

  • Page 20: Terrain/Riding Variations

    RIDING THE VEHICLE Deep Snow WARNING In deep “powder” snow, your vehicle When riding with a passenger: could begin to “bog” down. If this oc- – Braking ability and steering curs, turn in as wide an arc as possible control are reduced. Decrease and look for a firmer base.
  • Page 21 RIDING THE VEHICLE yourself plenty of room for stopping If a higher than safe speed is reached, and turning. This is especially true at slow down by braking but apply the night. brake with frequent light pressure. Never jam the brake and lock the track. Hard Packed Snow Side Hill Don't underestimate hard packed...
  • Page 22 RIDING THE VEHICLE Here are some web sites that can help Unseen Obstruction you finding important information: There may be obstructions hidden – Europe: www.avalanches.org beneath the snow. Driving off es- tablished trails and in the woods re- Slush quires reduced speed and increased vigilance.
  • Page 23 RIDING THE VEHICLE surfaces, “body english” is the key to snowmobile is no match for a train. turning. Leaning towards the inside of Before crossing a railroad track, stop, the turn and positioning body weight look and listen. on the inside foot will create a “bank- ing”...

  • Page 24: Environment

    RIDING THE VEHICLE Signals ture of our sport. Help us lead it down the right path! From all of us at BRP, If you intend to stop, raise either hand thank you for doing your share. straight above your head. A left turn is...
  • Page 25 RIDING THE VEHICLE Light Treading in no way suggests you Respecting the areas where we ride... should curb your appetite for snowmo- wherever they may be... is the only biling fun! It simply means tread with way to ensure their future enjoyment. respect! That's one major reason why we know you'll agree that Light Treading is smart...

  • Page 26: Traction Enhancing Products

    BRP for special studs installation. adaptation period. If your snowmobile is equipped with traction enhancing products, be sure to take plenty of time...

  • Page 27: Acceleration

    TRACTION ENHANCING PRODUCTS Acceleration Using studs on the track will allow your sled to accelerate better on packed snow and ice but will have no notice- able effect on soft snow. This can cause sudden variations in traction under certain conditions. WARNING A33A31A To prevent surprises that could...

  • Page 28: Important Safety Rules

    The use of traction enhancing products To ensure safe and proper installation, can increase the load and the stress on BRP recommends to have the studs in- certain snowmobile components, as stalled by your dealer. well as the vibration level. This can –...

  • Page 29: Inspection Of A Studded Track

    TRACTION ENHANCING PRODUCTS – Lugs that are broken or torn off, ex- WARNING posing portions of rods – See an authorized Lynx dealer – Delamination of the rubber for current specific studding – Broken rods availability and applications. – Broken studs (studded tracks) –...

  • Page 30: Important On-Product Labels

    IMPORTANT ON-PRODUCT LABELS Hang Tag Vehicle Safety Labels Read and understand all the safety la- bels on your vehicle. These labels are affixed to the vehicle for the safety of Dear consumer, the operator, passenger or bystander. Your new E-TEC engine technology has an automatic computer- r - controlled break-in period that ensures you get the most performance, efficiency and reliability for the life.
  • Page 31 IMPORTANT ON-PRODUCT LABELS WARNING AVERTISSEMENT 516002703 LABEL 2 516006903 LABEL 3 L L abel 4 WARNING Beware of rotating parts. 516006403 LABEL 1 Label 2 WARNING – Locate and read operator's guide. Improper snowmobile use can result in SEVERE IN- JURY or DEATH.
  • Page 32 IMPORTANT ON-PRODUCT LABELS Label 5 L L abel 8 WARNING WARNING Make sure seat is securely latched – Locate and read operator's before riding. guide. Follow all instructions and warnings. – Beware of hot parts. – Beware of hot vapors. –...
  • Page 33 IMPORTANT ON-PRODUCT LABELS Label 10 WARNING – Always use a rigid tow bar to tow. – NEVER carry a passenger on rear rack. – MAXIMUM REAR LOAD: 30 kg – MAXIMUM towing capacity: 5000N – MAXIMUM tongue capacity: 100N 516003886 LABEL 10 516005521 LABEL 11...

  • Page 34: Technical Information Labels

    IMPORTANT ON-PRODUCT LABELS fmo2014-003-008_a mmo2013-004-046_a ON FUEL INJECTORS - E-TEC ONLY fmo2015-003-004_a Technical Information Labels fmo2014-005-007_a 516003888 ALL MODELS EXCEPT COMMANDER GT-(COMFORT KIT) MODELS - LABEL 1 _______ ________ SAFETY INFORMATION...
  • Page 35 IMPORTANT ON-PRODUCT LABELS 516005876 LABEL 2 NOTICE Drive pulley bolt recommended torque 516005109 85-92 lbf·ft / 115-125N·m Not applying the recommended torque may result in a major failure of the drive COMMANDER GT (COMFORT KIT) MODELS pulley and the engine.Refer to the shop manual for the complete assembly procedure - ON PASSENGER HANDHOLD EN-516005503A-DEC ON PULLEY GUARD - LABEL 3...
  • Page 36 IMPORTANT ON-PRODUCT LABELS 516004294 ON CONSOLE NEAR SHIFT LEVER 516005672 ON CONSOLE - COMMANDER GT (COMFORT KIT)- MODELS OCTANE mmo2013-002-004 LOCATED ON FUEL CAP _______ ________ SAFETY INFORMATION...

  • Page 37: Vehicle Information

    VEHICLE INFORMATION _______________...

  • Page 38: Controls, Instruments And Equipment

    CONTROLS, INSTRUMENTS AND EQUIPMENT NOTE: Some features may not apply to your model or could be optional. NOTE: Some vehicle safety labels are not shown on illustrations. For information VEHICLE SAFETY LABELS on vehicle safety labels, refer to subsection. fmo2014-003-033_a TYPICAL ______________...
  • Page 39 CONTROLS, INSTRUMENTS AND EQUIPMENT fmo2013-003-002_a TYPICAL fmo2016-002-003_b COMMANDER GRAND TOURER 1200 4-TEC, 900 AND COMMANDER LIMITED 600 E-TEC fmo2012-003-016_b COMMANDER LIMITED 600 E-TEC AND 69 RANGER ARMY LTD fmo2014-003-004_a COMMANDER GRAND TOURER 1200 4-TEC AND 900 ECS² fmo2016-003-001_a COMMANDER LIMITED 600 E-TEC _______________...

  • Page 40: Handlebar

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2015-008-002_38 mmo2008-008-011_b TYPICAL - LH SIDE OF FUEL TANK - 900 ACE TYPICAL AND 1200 4-TEC 1. Throttle lever 2. To accelerate 1) Handlebar 3. To decelerate The handlebar controls the steering WARNING of the snowmobile. As the handlebar is rotated to right or left, the skis are Test the throttle lever operation turned right or left to steer the snow-...

  • Page 41: Brake Lever

    CONTROLS, INSTRUMENTS AND EQUIPMENT WARNING Test the throttle lever operation each time before starting the en- gine. The lever must return to its the rest position once released. Otherwise, do not start engine. Switching from Thumb to Finger Throttle Position mmo2015-008-100_a CAUTION It is highly recom- IF WANTED, CONTINUE TO ROTATE THE...

  • Page 42: Parking Brake Lever

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2014-004-001_a mmo2009-005-006_a TYPICAL 1. Brake lever TYPICAL — ENGAGE MECHANISM 2. To apply brake Step 1: Apply and hold regular brake Step 2: Lock brake lever using parking brake lever 4) Parking Brake Lever Parking brake lever is located on the LH To Release Parking Brake side of handlebar.

  • Page 43: Emergency Engine Stop Switch

    CONTROLS, INSTRUMENTS AND EQUIPMENT RF D.E.S.S. (Digitally Encoded The Lynx learning key, limits the speed Security System) of the snowmobile and the engine torque, therefore enabling first time The tether cord cap has an integrated users and less experienced operators D.E.S.S.

  • Page 44: Multifunction Switch

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2016-008-201_a ON POSITION fmo2014-003-003_a All operators of the snowmobile 1. Start button should familiarize themselves with the 2. Headlights dimmer switch function of the emergency engine stop 3. Heated grips switch by using it several times on first 4.
  • Page 45 CONTROLS, INSTRUMENTS AND EQUIPMENT Heated Grips Switch Heated Throttle Lever Switch fmo2014-003-003_c fmo2014-003-003_b TYPICAL TYPICAL 1. Heated throttle lever switch 1. Heated grips switch 2. Increase heat (Warmer) 2. Increase heat 3. Decrease heat (Colder) 3. Decrease heat NOTE: The heating intensity is dis- The heating intensity is displayed via played via the multifunction display the multifunction display.

  • Page 46: Gearshift Lever

    CONTROLS, INSTRUMENTS AND EQUIPMENT Mode/Set Button WARNING This button can be used instead of the Adjust with vehicle at rest in a safe two buttons on top of the analog/digital place. gauge to facilitate gauge adjustments. – When pressed left, it has the same 10) Tool Kit functions as the MODE (M) button.

  • Page 47: Front And Rear Bumpers

    CONTROLS, INSTRUMENTS AND EQUIPMENT Models with an Under Seat Storage Box fmo2012-003-007_a TYPICAL 1. Rear bumper fmo2015-003-001_a NOTICE Do not use skis or ski han- TYPICAL dles to pull or lift snowmobile. 1. Tool kit 12) Gauge 11) Front and Rear Bumpers WARNING To be used whenever snowmobile re-...
  • Page 48 CONTROLS, INSTRUMENTS AND EQUIPMENT WARNING Never adjust or set functions on the multifunction gauge while rid- ing the vehicle, you could lose con- trol. The multifunction display is used to: – Display the WELCOME message on power up – Display the KEY recognition mes- sage mmo2008-007-017 –...
  • Page 49 CONTROLS, INSTRUMENTS AND EQUIPMENT MONITORING SYS- See table below for usual pilot lamps information. Refer to for details on malfunction pilot lamps. PILOT LAMP(S) BEEPER MESSAGE DISPLAY DESCRIPTION 4 short Two stroke engine: Injection oil level is low. Stop vehicle beeps in a safe place then, replenish injection oil reservoir.
  • Page 50 CONTROLS, INSTRUMENTS AND EQUIPMENT Gauge Features AVAILABLE INDICATIONS IN NUMERICAL DISPLAY 800R 1200 FUNCTIONS 600 E-TEC 900 ACE E-TEC 4-TEC A) Speedometer B) Engine RPM C) Odometer D) Trip meter “A” or “B” E) Trip hour meter F) Clock G) Fuel level H) Altitude N.A.
  • Page 51 CONTROLS, INSTRUMENTS AND EQUIPMENT A) Speedometer Press the MODE (M) button to confirm selection or wait 5 seconds. addition analog type speedometer, vehicle speed can also be displayed via the multifunction display. Vehicle speed can be displayed on dis- play 1 or display 2. mmo2007-009-066_o B) Tachometer (RPM) In addition of the analog type tachome-...
  • Page 52 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_n mmo2007-009-066_p 1. RPM mode 1. Trip meter (TRIP A/TRIP B) mode Press the MODE (M) button to confirm Press and hold the SET (S) button to re- selection or wait 5 seconds. set. NOTE: Resetting TRIP B mode will also reset TOTAL FUEL CONSUMP- TION.
  • Page 53 CONTROLS, INSTRUMENTS AND EQUIPMENT H) Altitude Displays vehicle approximate altitude above sea level calculated from the barometric pressure. NOTE: Altitude displayed is rounded off every 100 meters (gauge set in metric) or 200 feet (gauge set in impe- rial units). mmo2007-009-066_k To display vehicle altitude, proceed as follows.
  • Page 54 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_o I) Heated Grips Heating Intensity mmo2007-009-044_a HEATED THROTTLE LEVER Bar gauge that indicates heating inten- 1. Operating range sity. K) Instant Fuel Consumption NOTE: There are nine intensity set- tings. When released, display will re- Calculates vehicle average fuel con- turn to engine coolant temperature (if sumption while riding.
  • Page 55 CONTROLS, INSTRUMENTS AND EQUIPMENT Press the MODE (M) button to confirm TC appears when the mode is se- selection or wait 5 seconds. lected. mmo2008-003-021_a TYPICAL mmo2007-009-066_o Press the MODE (M) button to confirm L) Total Fuel Consumption selection or wait 5 seconds. Records vehicle average fuel con- sumption since it has been reset.
  • Page 56 CONTROLS, INSTRUMENTS AND EQUIPMENT P) Top Speed Records vehicle top speed since it has been reset. To display vehicle top speed, proceed as follow. Push the MODE (M) button to select display. mmo2007-009-066_w M) Message Display mmo2007-009-066_m NOTE: Display will flash for approxi- mately 5 seconds, then will return to mmo2007-009-066_c the previously selected mode if display...
  • Page 57 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_o mmo2007-009-066_m To reset, push the MODE (M) to select NOTE: Display will flash for approxi- mode. mately 5 seconds, then will return to the previously selected mode if display is not changed. Push SET (S) button to select vehicle average speed (AVR_SPD) mode.

  • Page 58: Backrest (If Applicable)

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_m mmo2007-009-066_k Push and hold the SET (S) button within To change HOURS, while the value of 5 seconds to reset. HOURS is blinking, use the SET (S) but- ton to change hours. To change MINUTES, while the value of HOURS is blinking, press the MODE (M) button to switch to minutes.

  • Page 59: Passengers Handholds (If Applicable)

    CONTROLS, INSTRUMENTS AND EQUIPMENT Passenger Seat Removal 2. Slightly incline the passenger seat towards front and engage both seat To remove the passenger seat, pro- hooks in the storage box lid slots. ceed as follows: 1. Disconnect the accessories con- nector by pulling.
  • Page 60 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2009-004-019 mmo2009-004-022_a Step 1: Pull up Step 2: Unscrew 2. Refer to the decal located on the RH backrest bracket and guide the handhold to the desired position. NOTE: The decal can also be seen in IMPORTANT ON-PRODUCT LA- BELS subsection of this guide.

  • Page 61: Storage Compartment

    CONTROLS, INSTRUMENTS AND EQUIPMENT 16) Mountain Strap (69 Ranger Army LTD and Commander (Except GT) Models) Mountain strap provides a grip for the driver when side-hilling. fmo2009-004-024_a Step 1: Pull rubber tab Step 2: Lift RH side To close lid, simply push it down until it latches.

  • Page 62: Rear Rack

    CONTROLS, INSTRUMENTS AND EQUIPMENT fmo2012-003-004 mmo2009-005-010_a 1. Off 18) Rear Rack 2. Warm 3. Hot The rear rack can accommodate per- Commander Grand Tourer 1200 sonal articles (luggage), a fuel caddy or the storage box. WARNING All objects in rear rack must be properly latched.

  • Page 63: Adjustable Handlebar

    2. Push safety tab forward to free ac- cessory attachment from the hitch. BRP does not recommend to ride a snowmobile equipped with high lug 3. Detach accessory attachment. profile track at high speed in a trail, on 4.

  • Page 64: Fuses

    CONTROLS, INSTRUMENTS AND EQUIPMENT In the event that you have to, reduce your speed, then minimize the dis- tance you ride on those surfaces. CAUTION Running those tracks at high speed in a trail, on hard packed surfaces or ice put more stress on the lugs, which tend to heat up as a result.

  • Page 65: Drive Belt Guard

    CONTROLS, INSTRUMENTS AND EQUIPMENT NOTICE Do not exceed maximum Drive Belt Guard Installation load capacity of rear rack. MAXI- When reinstalling drive belt guard, MUM cargo load is 30 kg (66 lb). position its cutaway toward front of snowmobile. 26) Drive Belt Guard Place belt guard front openings over tabs.

  • Page 66: Hood

    CONTROLS, INSTRUMENTS AND EQUIPMENT 27) Hood 3. Hook the rubber ties. WARNING 28) Upper Side Panels Never operate engine with hood WARNING removed from vehicle. Never operate engine with side Hood Removal panels opened or removed from vehicle. 1. Remove upper side panels as ex- plained below.

  • Page 67: Lower Side Panels

    CONTROLS, INSTRUMENTS AND EQUIPMENT 2. Hook the panel top center tabs to the console. mmo2009-004-044_a 1. Rubber tie mmo2011-006-100_a 1. Console hook 3. Turn the clip 1/4 turn counterclock- 2. Console slot 3. Panel center tabs wise to unlock. 3. Insert the rear tab into the console slot.

  • Page 68: Rewind Starter Handle (If Applicable)

    CONTROLS, INSTRUMENTS AND EQUIPMENT 30) Rewind Starter Handle 2. Insert the lower section of side panel over the aluminium chassis (If Applicable) and the aluminium tab into the panel Auto-rewind type located on right hand slot. side of snowmobile behind side panel. To engage mechanism, pull handle slowly until a resistance is felt then pull vigorously.

  • Page 69: Storage Box (If Applicable)

    CONTROLS, INSTRUMENTS AND EQUIPMENT NOTE: Do not sit or lean on seat when To install storage box, make sure that fuel tank cap is not properly installed. the tunnel surface is clean. Put stor- age box within the rear rack rails. 33) Storage Box (If Attach using...

  • Page 70: Seat Heater (If Applicable)

    CONTROLS, INSTRUMENTS AND EQUIPMENT fmo2016-002-003_c 1. ECS², module mmo2015-008-002_a TYPICAL - LH SIDE OF FUEL TANK REAR SUSPENSION ADJUST- Refer to 1. Mode switch MENT TUNE YOUR RIDE in the sec- tion It is used to activate or deactivate Eco/Standard/Sport modes. 37) Seat heater (If OPERATING MODES Refer to...

  • Page 71: Fuel And Oil

    FUEL AND OIL Fuel Requirements MINIMUM FUEL ENGINE OCTANE TYPE NOTICE Always use fresh gaso- RATING line. Gasoline will oxidize; the re- Fuel 600 HO sult is loss of octane, volatile com- which E-TEC pounds, and the production of gum 800 R and varnish deposits which can contain...

  • Page 72: Recommended Oil

    The engine of this snow- cap) have vehicle inspected mobile has been developed and val- and/or repaired before further idated using the BRP XPS™ Synthe- operation. tic 4-stroke oil. BRP recommends – Fuel is flammable and explosive the use of its XPS Synthetic 4-stroke under certain conditions.
  • Page 73 FUEL AND OIL To Add Injection Oil Remove injection oil reservoir cap. Add injection oil. Reinstall cap and fully tighten. NOTE: Do not overfill. Do not pass the MAX range in the reservoir filler neck. NOTICE mismatch reservoir cap with fuel tank cap. WARNING Wipe off any oil spills.

  • Page 74: Break-In Period

    BREAK-IN PERIOD Operation During Break-In – Avoid pulling a load. – Avoid high speed cruising. A break-in period of 10 operating hours or 500 km (300 mi) is required for the vehicle. After the break-in period, the vehicle should be inspected by an authorized Lynx dealer, repair shop, or person of MAINTE- your own choosing.

  • Page 75: Operating Modes (900 Ace And 1200 4-Tec)

    OPERATING MODES (900 ACE AND 1200 4-TEC) To increase power, press the switch WARNING upwards. To decrease power, press Whenever changing operating the switch downwards. mode, make sure to maintain situ- ational awareness while riding. ECO Mode (Fuel Economy Mode) When ECO mode is selected (fuel economy mode), vehicle torque and speed are limited whereby an optimal...

  • Page 76: Learning Key Modes

    OPERATING MODES (900 ACE AND 1200 4-TEC) Learning Key Modes The learning key provides a mode of operation whereby engine torque and speed are limited. NOTE: The initial learning key pro- gramming limit speed 40 km/h (25 MPH) 70 km/h (43 MPH).

  • Page 77: Operating Instructions

    OPERATING INSTRUCTIONS Engine Starting Procedure E-TEC Models If the starter does not operate and you Procedure ENGINE have followed the steps in STARTING PROCEDURE 1. Apply parking brake. , start engine with the emergency cord as follows: 2. Recheck throttle lever operation. 3.

  • Page 78: Vehicle Warm-Up

    OPERATING INSTRUCTIONS mmo2008-005-007 3. Attach the other end of emergency mmo2008-005-014_a rope to the starter clip supplied in 6. Pull the rope using a sharp, crisp pull the tool kit. so the rope comes free of the drive pulley. WARNING When starting the snowmobile in an emergency situation, using drive pulley, do not reinstall the...

  • Page 79: Gearbox Operation

    OPERATING INSTRUCTIONS NOTICE If vehicle does not move Neutral when throttle is applied, stop en- When set in neutral (N), the gearbox gine, remove tether cord cap from disengages the pulleys from the track. the engine cut-off switch, then do the following.

  • Page 80: Shifter Rod Adjustment

    OPERATING INSTRUCTIONS Shifter rod adjustment WARNING 1. Adjust shifter rod to initial length Never tow an accessory with a from end to end 258mm rope. Always use a rigid tow bar. Using a rope would result in a col- 2. Mount the rod to the vehicle lision between the object and the 3.

  • Page 81: Tune Your Ride

    TUNE YOUR RIDE Following are guidelines to fine-tune WARNING suspension. Suspension adjustment could af- fect vehicle handling. Always take REAR AND FRONT SUSPENSION time to familiarize yourself with SPRING PRELOAD FACTORY the vehicle's behavior after any SETTINGS suspension adjustment have been REAR FRONT made.

  • Page 82: Rear Suspension Adjustment

    TUNE YOUR RIDE Rear Suspension REFERENCE TABLE Adjustment WEIGHT NOTICE TRANSFER WHAT TO DO Whenever adjusting rear (SKI PRESSURE) suspension, check track tension and adjust as necessary. Comfortable: good No adjustment weight transfer required (light pressure) Light: too much Strap too long, weight transfer reduce strap (lift off the ground)
  • Page 83 TUNE YOUR RIDE Generally, a longer stopper strap set- ting gives better performance in deep snow on a flat landscape. Rear Springs Rear spring preload has an effect on comfort, ride height and load compen- sation. Also, adjusting rear spring preload shifts more or less weight to the snow- mmo2006-003-022_a mobile front end.
  • Page 84 TUNE YOUR RIDE Electronic Controlled Suspension Spring Preload Adjuster ( ECS²) (MAN=manual) The spring preload is fundamental for Commander 600 E-TEC Limited, the function of the suspension. If the Commander Grand Tourer 900 ACE preload is incorrectly set, any other and 1200 4-TEC ECS²...
  • Page 85 TUNE YOUR RIDE is more spring preload/damping force REFERENCE TABLE and down is less spring preload/damp- STEERING ing force. WHAT TO DO BEHAVIOR WARNING Easy to turn No adjustment required When adjusting ECS², be sure to (neutral) maintain situational awareness of Harder to turn Adjusted too soft, other snowmobiles, obstacles or...

  • Page 86: Front Suspension Adjustment

    TUNE YOUR RIDE WARNING Always adjust both front springs to same position. REFERENCE TABLE HANDLING WHAT TO DO Good: steering No adjustment comfortable to turn required Adjusted too soft, fmo2013-005-003_a Bad: steering too increase spring CENTER ARM easy to turn 1.

  • Page 87: Vehicle Behavior Related To Suspension Adjustment

    TUNE YOUR RIDE Vehicle Behavior Related to Suspension Adjustment PROBLEM CORRECTIVE MEASURES Check ski alignment and camber angle adjustment. See an authorized Lynx dealer. Reduce ski ground pressure. Front suspension wandering – Reduce front suspension spring preload. – Increase center spring preload. –...

  • Page 88: Vehicle Transportation

    VEHICLE TRANSPORTATION Make sure that oil reservoir and fuel tank caps are properly installed. Tilt bed trailers can easily be equipped with a winch mechanism to afford maximum safety in loading. Simple as it may seem, never drive your snow- mobile onto a tilt bed trailer or any other kind of trailer or vehicle.
  • Page 89 MAINTENANCE _______________...

  • Page 90: First Inspection

    FIRST INSPECTION After the first 10 hours or 500 km (300 mi) of operation, whichever comes first, your vehicle have to be inspected by an authorized Lynx dealer, repair shop, or person of your own choosing. The break-in inspection is very important and must not be neglected.
  • Page 91 FIRST INSPECTION FIRST INSPECTION (4-STROKE) AFTER THE FIRST 500 KM (300 MI) OR 10 HOURS OF OPERATION, WHICHEVER COMES FIRST Inspect engine seals and gaskets for leaks Inspect exhaust system and check for leaks ENGINE Check coolant level FUEL Inspect fuel lines and connections SYSTEM Inspect drive belt Visually inspect drive pulley...

  • Page 92: Maintenance Schedule (2-Stroke)

    MAINTENANCE SCHEDULE (2-STROKE) NOTE: The maintenance schedule does not exempt the pre-ride inspection. WARNING Failure to properly maintain the vehicle according to the maintenance schedule and procedures can make it unsafe to operate. EVERY 1 500 KM (1,000 MI) Models with chaincase: Adjust drive chain DRIVE Models with chaincase: Check chaincase oil level SYSTEM...
  • Page 93 MAINTENANCE SCHEDULE (2-STROKE) EVERY 6 000 KM (4,000 MI) OR 2 YEARS (WHICHEVER COMES FIRST) Clean and lubricate rewind starter ENGINE Inspect fuel pump strainer and replace if necessary FUEL SYSTEM Inspect throttle cable Replace brake fluid Lubricate the splines of joint between QRS axle and gearbox (XU models) DRIVE Lubricate the splines of joint between driven pulley and QRS axle ( XU...

  • Page 94: Maintenance Schedule (4-Stroke)

    MAINTENANCE SCHEDULE (4-STROKE) NOTE: The maintenance schedule does not exempt the pre-ride inspection. WARNING Failure to properly maintain the vehicle according to the maintenance schedule and procedures can make it unsafe to operate. EVERY 1 500 KM (1,000 MI) Models with chaincase: Adjust drive chain DRIVE Models with chaincase: Check chaincase oil level SYSTEM...
  • Page 95 MAINTENANCE SCHEDULE (4-STROKE) EVERY 6 000 KM (4,000 MI) OR 2 YEARS (WHICHEVER COMES FIRST) Replace fuel filter FUEL SYSTEM Replace fuel pump outlet filter (ACE) Replace drive pulley slider shoes, O-ring and rollers and inspect ramps (1200 4-TEC and 900 ACE) DRIVE Replace brake fluid SYSTEM AND...

  • Page 96: Maintenance Procedures

    MAINTENANCE PROCEDURES Engine Coolant This subsection includes instructions for basic maintenance procedures. WARNING WARNING Never open coolant tank cap when Turn off the engine, remove tether engine is hot. cord cap and follow these mainte- nance procedures when perform- Engine Coolant level ing maintenance.

  • Page 97: Injection Oil (600 Ho E-Tec, 800R E-Tec)

    MAINTENANCE PROCEDURES Recommended Engine Coolant COOLANT LONG LIFE ANTIFREEZE(F) recommended (P/N 619 590 204) product Distilled water and Alternative, or antifreeze solution if not available (50% distilled water, 50% antifreeze) fmo2012-003-012_a NOTICE A blend of 50% antifreeze TYPICAL with 50% distilled water will im- 1.

  • Page 98: Engine Oil Replacement (900 Ace)

    MAINTENANCE PROCEDURES 4. Open the LH side panel, refer to 2. Remove the LH side panel. CONTROLS, INSTRUMENTS AND 3. Remove dipstick. EQUIPMENT 5. Remove the drive belt guard, refer DRIVE BELT GUARD 6. Remove dipstick from the filler tube, then wipe it clean.

  • Page 99: Engine Oil Replacement (1200 4-Tec)

    MAINTENANCE PROCEDURES mmr2011-070-004_a fmo2016-003-012_b 1. Sealing washer 2. Oil drain plug PIVOT THE ACCESS COVER 1. Retaining screws 10. Install drain plugs and tighten to 5. Clean drain plug area. the specified torque. 6. Place a drain pan under the bottom DRAIN PLUGS TIGHTENING TORQUE pan opening.
  • Page 100 MAINTENANCE PROCEDURES NOTICE NOTICE Engine oil and oil filter Never sealing must be replaced at the same time. washer a second time. Always re- place with a new one. 1. Place vehicle on a level surface. 2. Remove the LH side panel. 3.

  • Page 101: Engine Oil Filter (900 Ace)

    MAINTENANCE PROCEDURES Engine Oil Filter (900 ACE) Engine Oil Filter Replacement Oil Filter Removal 1. Remove the RH side panel. 2. Clean oil filter area. 3. Remove: – Oil filter cover screws – Oil filter cover with O-ring mmr2011-070-008_a – Oil filter. 1.

  • Page 102: Exhaust System

    MAINTENANCE PROCEDURES – Oil filter cover with O-ring – Oil filter. mmr2009-111-008_a 1. Lubricate with engine oil 4. Install the oil filter cover. 5. Tighten oil filter cover screws to the mmr2009-111-006_a specified torque. 1. Oil filter cover screws 2. Oil filter cover OIL FILTER COVER TIGHTENING 3.
  • Page 103 MAINTENANCE PROCEDURES ogy. Though not required, it is recom- WARNING mended that an authorized Lynx dealer Always wear safety goggles when performs spark plugs inspection or re- using pressurized air. placement. Recommended Spark Plug Unscrew spark plugs completely then remove them. CAUTION Use only spark plug Installation mentioned list below.

  • Page 104: Engine Stopper ( E-Tec Models)

    MAINTENANCE PROCEDURES CAUTION Do not attempt to adjust gap on these plugs. Spark plug Spark plug Model type mmo2008-008-006_a NEW SPARK PLUG 600 HO adjustable. 1. Torque 1/2 of a turn E-TEC PZFR6F 0.75mm ± 0.05 mm adjustable. 0.75 + 0.05 800R E-TEC PFR7AB mm/- 0.05...

  • Page 105: Brake Fluid

    MAINTENANCE PROCEDURES mmo2010-009-002_a 1. Rubber stop block mmo2010-009-007_a 2. Bump 1. Drive pulley 3. Feeler gauge 2. Engine stopper screws 3. Engine stopper 7. Tighten screws to the specified torque, following the illustrated se- 5. Insert a 0.5 mm (.02 in) feeler gauge quence.

  • Page 106: Gearbox Oil

    The gearbox of this snowmobile has painted and plastic parts. Handle been developed and validated using with care. Rinse thoroughly in case the XPS™ Synthetic gear oil. BRP of spillage. strongly recommends the use of its Brake Fluid Level XPS Synthetic gear oil at all times.

  • Page 107: Drive Belt

    MAINTENANCE PROCEDURES CAUTION To avoid damages to the drive belt, ensure that things which are carried in storage box are not damaged the spare drive belt. Drive Belt Replacement Drive Belt Removal 1. Remove tether cord cap from en- gine cut-off switch. CON- 2.
  • Page 108 MAINTENANCE PROCEDURES NOTICE Do not force or use tools to pry the belt into place, as this could cut or break the cords in the belt. NOTE: The maximum drive belt life span is obtained when belt is installed with arrows in the direction of rotation. mmo2011-003-010_a ALUMINUM ADJUSTER HUB 1.

  • Page 109: Drive Pulley

    MAINTENANCE PROCEDURES Belt with External Cogs SIDE 8. Close side panel, refer to PANELS CONTROLS, INSTRU- Repeat step 5 until the bottom of MENTS AND EQUIPMENT subsec- grooves on the external side of drive tion. belt are flush with the driven pulley edges.
  • Page 110 MAINTENANCE PROCEDURES Calibration screws should be adjusted Procedure so that actual maximum engine RPM Just loosen lock nut enough to pull matches the maximum horsepower calibration screw partially out and RPM. adjust to desired position. Do not completely remove the lock nut. MAXIMUM ENGINE Torque lock nuts to 10 N•m ±...

  • Page 111: Track

    Lynx dealer. Snowmobiles Equipped with Traction Enhancing Products If your snowmobile is equipped with a BRP approved studded track, PRO- CEED WITH A VISUAL INSPECTION OF YOUR TRACK BEFORE EACH USE. Look for any defects, such as: –...
  • Page 112 MAINTENANCE PROCEDURES WARNING To prevent serious injury to indi- viduals near the snowmobile: – NEVER stand behind or near a mmr2009-133-003_b moving track. DEFLECTION SETTING 1. Bottom O-ring set to specification – Always use a wide-base snow- mobile stand with a rear deflec- 6.
  • Page 113 MAINTENANCE PROCEDURES mmr2009-133-003_a LOAD READING 1. Upper O-ring 10. Load reading must be as per the following table. TRACK ADJUSTMENT SPECIFICATION fmr2008-048-008_a 1. RH rear idler wheel bolt TRACK 40 mm to 50 mm DEFLECTION 4. Tighten or loosen both adjustment (1.5 in to 2 in) SETTING screws to increase or decrease...
  • Page 114 MAINTENANCE PROCEDURES Track Alignment WARNING Remove the tether cord cap from WARNING engine cut-off switch before per- Before checking track alignment, forming any maintenance or ad- ensure that the track is free of all justment, unless otherwise spec- particles which could be thrown ified.

  • Page 115: Suspension

    MAINTENANCE PROCEDURES fmo2015-003-008_a 1. Grease fittings A05F0EB TYPICAL Steering and Front Suspension 1. Locknut Condition 2. Retaining bolts Visually inspect steering and front sus- 6. Start engine and rotate track slowly pension for tightness of components to recheck alignment. (steering arms, control arms and links, tie rods, ball joints, ski bolts, ski legs, 7.

  • Page 116: Fuses

    MAINTENANCE PROCEDURES Ski stance can be adjusted by spacer Fuse Location location. It can be installed inside or The fuse box is located behind the front outside of the ski leg seat upholstery at the LH front lower portion of seat. Refer to the decal inside the fuse box SPECIFICATIONS cover or the...
  • Page 117 MAINTENANCE PROCEDURES Headlights Bulb Replacement NOTICE Never touch glass portion of an halogen bulb with bare fingers, it shortens its operating life. If glass is touched, clean it with isopropyl al- cohol which will not leave a film on the bulb. mmo2007-009-022_a 1.
  • Page 118 MAINTENANCE PROCEDURES NOTE: Led taillight: leds cannot be re- placed. If led taillight is failed change taillight assembly. Fasten new taillight by screws. mmo2007-009-023_a TYPICAL 1. Knobs Taillight Bulb Replacement 1. Carefully pull taillight assembly by both ends at the same time. fmr2011-001-003 NOTICE Plastic retaining pins...

  • Page 119: Vehicle Care

    To remove grease, oil and grime, use BRP HEAVY DUTY CLEANER (P/N 293 110 001). NOTICE Do not use heavy duty cleaner on decals or vinyl. To remove stubborn dirt from all plastic and vinyl surfaces, use XPS ALL PUR- POSE CLEANER (P/N 219 701 709).

  • Page 120: Storage

    STORAGE During summer, or when a snowmobile is not in use for more than three months, proper storage is necessary. STORAGE Clean the vehicle VEHICLE ENGINE STORAGE MODE E-TEC models: Lubricate engine. See (E-TEC) below for instructions. Block muffler with rags ENGINE Protect fuel system by adding fuel stabilizer to fuel following the product manufacturer recommendations.
  • Page 121 STORAGE NOTE: The storage mode does not The engine lubrication function takes function in other modes (trip A, trip B approximately 1 minute. During this and hr trip). time engine RPM will increase slightly to approximately 1600 RPM and the oil 4.

  • Page 122: Preseason Preparation

    PRESEASON PREPARATION PRESEASON PREPARATION (2-STROKE) Inspect engine rubber mounts Check exhaust system condition and check for leaks Tighten exhaust manifold screws or nuts to specified torque ENGINE Inspect cooling system cap, hoses and clamps and check for leaks Check coolant density Inspect crankshaft PTO seal Inspect fuel lines and connections FUEL...
  • Page 123 PRESEASON PREPARATION PRESEASON PREPARATION (4-STROKE) Visually inspect engine seals and gaskets and check for leaks Check exhaust system condition and check for leaks ENGINE Change engine oil and filter Check coolant density Inspect fuel lines and connections FUEL SYSTEM Clean and inspect throttle body Inspect drive belt (adjust at every drive belt replacement) Clean and visually inspect drive pulley Clean and inspect driven pulley...
  • Page 124 PRESEASON PREPARATION This page is intentionally blank ______________...

  • Page 125: Technical Information

    TECHNICAL INFORMATION ______________...

  • Page 126: Vehicle Identification

    These numbers are required by the authorized Lynx dealer to complete warranty claims properly. No warranty will be allowed by BRP if the engine identification number or vehicle iden- tification number (VIN) is removed or mutilated in any way. We strongly rec-...
  • Page 127 VEHICLE IDENTIFICATION mmo2007-002-006_a 800R E-TEC ENGINE 1. Engine identification number mmo2009-005-039_a 1200 4-TEC ENGINE 1. Engine serial number mmo2014-004-007_a 900 ACE ENGINE 1. Engine identification number ______________...

  • Page 128: Noise Emission And Vibration Values

    NOISE EMISSION AND VIBRATION VALUES MODEL 600 HO E-TEC 800R E-TEC 1200 4-TEC 900 ACE NOISE EMISSION AND VIBRATION VALUES 96,7 dB @ 99,3 dB @ 98,1 dB @ 92,7 dB @ Sound power 4050 RPM 3950 RPM 3900 RPM 3625 RPM level (L (Uncertainty...

  • Page 129: Ec-Declaration Of Conformity

    The EC-Declaration of Conformity does not appear in this version of the Operator's Guide. Please refer to the printed version that was delivered with your vehicle. ddd2009-001...

  • Page 130: Radio Frequency Digitally Encoded Security System

    RADIO FREQUENCY DIGITALLY ENCODED SECURITY SYSTEM (RF D.E.S.S. KEY) This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

  • Page 131: Specifications

    SPECIFICATIONS SYSTEM MODELS ENGINE 600HO E-TEC Engine type Rotax ® 593, liquid cooled w/Reed valve, 3D-RAVE Cylinders Displacement 594.4 cm³ (36.27 in³) Bore 72 mm (2.83 in) Stroke 73 mm (2.87 in) Maximum horsepower engine RPM 8100 RPM Fuel injection system E-TEC direct injection Exhaust system Single tuned pipe, baffle muffler...
  • Page 132 SPECIFICATIONS ENGINE 900 ACE Engine type Rotax 903, liquid cooled, 4-stroke, D.O.H.C., dry sump Cylinders Displacement 899 cm³ (54.9 in³) Bore 74 mm (2.9 in) Stroke 69.7 mm (2.74 in) Maximum horsepower RPM 7250 RPM Exhaust system Single front pipe, baffle muffler (P/N 619 590 114) or SAE 0W 40 API SM Engine oil...
  • Page 133 SPECIFICATIONS ENGINE 1200 4-TEC Rotax 1203, liquid cooled, 4-Stroke, D.O.H.C. Engine type with balancer shaft, dry sump Cylinders Displacement 1 170.7 cm³ (71.44 in³) Bore 91 mm (3.58 in) Stroke 60 mm (2.36 in) Maximum horsepower engine RPM 7800 RPM Fuel injection system Multi point EFI, 52 mm heated throttle body Exhaust system...
  • Page 134 SPECIFICATIONS DRIVE SYSTEM 600 HO E-TEC TRA III™ 800 R Type TRA VII™ E-TEC 1200 4-TEC eDrive II Drive pulley 900 ACE 600 HO E-TEC 3000 RPM ± 100 800 R 3800 RPM ± 100 Engagement E-TEC 1200 4-TEC 2200 RPM ± 100 900 ACE Driven pulley type QRS-SS...
  • Page 135 SPECIFICATIONS DRIVE SYSTEM (cont’d) Deflection 40 mm to 50 mm (1.575 in to 1.969 in) Track tension Force 7.3 kgf (16 lbf) Equal distance between edges of track guides Track alignment and slider shoes BRAKE SYSTEM Brake system Brembo/Hydrauloc caliper, self adjustable/disk Brake fluid DOT 4 SUSPENSION...
  • Page 136 SPECIFICATIONS ELECTRICAL SYSTEM 600 HO E-TEC Lightning system output 12V/1340 W Headlights bulb HI/LOW beam 2 x 60/55 Watts (H-4) Taillight bulb Type NGK PZFR6F Spark plug 0.75 mm ± 0.05 mm (.03 in ± .002 in) (Not adjustable) F 1: Battery 30 A F 2: Start F 3: Front power outlet...
  • Page 137 SPECIFICATIONS ELECTRICAL SYSTEM 800 R E-TEC Lightning system output 12V/1340W Headlights bulb HI/LOW beam 2 x 60/55 Watts (H-4) Taillight bulb Type NGK PFR7AB Spark plug 0.75 mm ± 0.05 mm (.03 in ± .002 in) (Not adjustable) F 1: Battery 30 A F 2: Start F 3: Front power outlet...
  • Page 138 SPECIFICATIONS ELECTRICAL SYSTEM 900 ACE Lightning system output 12V / 650 W Headlights bulb HI/LOW beam 2 x 60/55 Watts (H-4) Taillight bulb 2.6 W / 139m W LED Type MR7B1 Spark Plug 0.8 mm (.031 in) F1 : Battery 30 A F2 : Relay / Start button F3 : Starter solenoid...
  • Page 139 SPECIFICATIONS ELECTRICAL SYSTEM 1200 4-TEC Lightning system output 12V/490 W Headlights bulb HI/LOW beam 2 x 60/55 Watts (H-4) Taillight bulb Type NGK CR8EKB Spark plug Not adjustable F 1: Battery 30 A F 2: Relay/start button F 3: Starter solenoid 10 A F 4: Fan 15 A...
  • Page 140 SPECIFICATIONS WEIGHT AND DIMENSIONS Commander 600 HO E-TEC 287 kg (633 lb) Commander 600 HO E-TEC 296 kg (653 lb) ICE ripper Commander LTD 600 HO 303 kg (668 lb) E-TEC Commander LTD 600 HO 304 kg (670 lb) E-TEC ECS Commander 800R E-TEC 294 kg (648 lb) Commander 900 ACE...

  • Page 141: Troubleshooting

    TROUBLESHOOTING ______________...

  • Page 142: Troubleshooting Guidelines

    TROUBLESHOOTING GUIDELINES ELECTRIC STARTER DOES NOT WORK 1. Emergency engine stop switch in OFF position or tether cord cap not installed on engine cut-off switch. – Place the emergency engine stop switch in the ON position and install tether cord cap (on engine cut-off switch. 2.
  • Page 143 TROUBLESHOOTING GUIDELINES ENGINE LACKS ACCELERATION OR POWER (cont’d) 4. Engine break-in period not completed (E-TEC). – Complete break-in period. 5. Incorrect drive pulley adjustment. – Adjust drive pulley, refer to MAINTENANCE PROCEDURES. 6. Drive and driven pulleys require servicing. – Contact an authorized Lynx dealer. 7.
  • Page 144 TROUBLESHOOTING GUIDELINES HEATED GRIPS/THUMB WARMERS ARE NOT WORKING 1. Engine RPM is too low. – Make sure engine RPM is above 2000. ENGINE HAS SHUT DOWN 1. The engine shuts down after long periods of idling. – Do not let engine idle too long. Refer to VEHICLE WARM-UP in OPERATING INSTRUCTION.

  • Page 145: Monitoring System

    MONITORING SYSTEM Pilot Lamps, Messages and Beeper Codes Gauge pilot lamp(s) will inform you if an anomaly occurs or to inform you of a particular condition. mmo2008-003-024_a TYPICAL — PILOT LAMPS Pilot lamp can flash alone or in combi- nation with another lamp. On the multifunction analog/digital gauge, the display is used as a comple- ment of the pilot lamps to give you a...
  • Page 146 MONITORING SYSTEM NOTE: Some of the listed pilot lamps and messages do not apply to all models. PILOT MESSAGE LAMP(S) BEEPER DESCRIPTION DISPLAY 4 short Four stroke engines: Low engine oil beeps pressure. Stop vehicle in a safe place then, every LOW OIL check oil level.
  • Page 147 MONITORING SYSTEM PILOT MESSAGE LAMP(S) BEEPER DESCRIPTION DISPLAY 4 short beeps Engine RPM limited for protection when — every REV LIMIT certain faults occur. minutes On E-TEC engines, indicates that maximum — — OVER REV engine RPM is reached. Check clutch calibration.

  • Page 148: How To Read Fault Codes

    MONITORING SYSTEM How to Read Fault Codes Multifunction Analog/Digital Display Only To read any active fault code, press and hold MODE (M) Button and simul- taneously depress the HI/LOW beam switch repeatedly several times. If two or more codes are registered, use SET (S) or MODE (M) to scroll.

  • Page 149: Warranty

    WARRANTY ______________...

  • Page 150: Brp Finland Oy International Limited Warranty: 2017 Lynx

    Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 151 LYNX parts without charge for parts and labor, at any authorized BRP distributor/dealer during the warranty coverage period. BRP reserves the right to improve or modify products from time to time without as- suming any obligation to modify products previously manufactured.
  • Page 152 BRP or an authorised BRP distributor / dealer receives a proof that the former owner agreed to the transfer of ownership, in addition to the co-ordinates of the new owner.

  • Page 153: Maintenance Records

    MAINTENANCE RECORDS Send photocopy of maintenance record to BRP if needed. PREDELIVERY Serial number: Signature/Print: Mileage / km: Hours: Date: Dealer no: Notes: Refer to vehicle Pre-Delivery Bulletin for detailed installation procedures FIRST INSPECTION Serial number: Signature/Print: Mileage / km:...
  • Page 154 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print:...
  • Page 155 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print:...
  • Page 156 This page is intentionally blank ______________...

  • Page 157: Customer Information

    CUSTOMER INFORMATION ______________...

  • Page 158: Contact Us

    CONTACT US NorthAmerica www.brp.com 565 de laMontagne Street Europe Valcourt (Québec) J0E 2L0 Canada PL 8040 (Isoaavantie 7) 96101 Rovaniemi Finland Circuito de la Productividad #111 Parque Industrial Guadalajara Col. Las Pintas Formvägen 16 El Salto, Jalisco, 45690 S-906 21 Umeå...

  • Page 159: Change Of Address/Ownership

    Notifying BRP, even after the expiration of the limited warranty, is very important as it enables BRP to reach the snowmobile owner if necessary, like when safety re- calls are initiated. It is the owner’s responsibility to notify BRP.
  • Page 160 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 161 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 162 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 163 CHANGE OF ADDRESS/OWNERSHIP fmo2015-005-004 en ______________...
  • Page 164 ® and the BRP logo are trademarks of Bombardier Recreational Product Inc. or its affiliates.

This manual is also suitable for:

Lynx xu 800 r e-tecLynx xu 1200 4-tecLynx xu 900ace

Table of Contents