Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Confycare EL08
Summary of Contents for Confycare EL08
- Page 1 EL08 / EL08B / EL08F / EL08FS Electrical Chiropractic Table...
- Page 3 SAFETY PRECAUTIONS REGULATION AND PRODUCT STANDARDS 1. During the adjustment of the table, do not put any part of the body into the gap of any moving parts. This table complies with the European regulation of medical devices (EU) 2017/745 and with the following 2.
-
Page 4: Technical Specifications
This Product dimensions could create a dangerous situation where your leg is caught between the section and the peripheral EL08 - Base Chiropractic Table foot bar or floor surface. Length: 1800-1930mm Take into account the weight distribution on the Width: 550mm table when working. -
Page 5: Operation
EL08 Base Chiropractic Table Please make sure that there are no objects in the space under the table before any operation. OPERATION The table should be placed at the lowest level to reduce the risk of injury caused by the patient Connect the bed to an electrical outlet using the power falling off the table when unattended. - Page 6 Adjusting head plate width As shown in Figure 7, pull the control lever to adjust the width of the head plates. Figure 10 Extended leg segment adjustment control lever For adjustment of the height and length of the foot rest, loosen the correct knob as shown below.
- Page 7 EL08B Chiropractic Breakaway Table The table should be placed at the lowest level to reduce the risk of injury caused by the patient OPERATION falling off the table when unattended. Connect the bed to an electrical outlet using the power cord.
- Page 8 Adjust the pull rod indicated by the arrow, and the middle section of the bed can be raised by 35 degrees.(Figure 11) highest angle 35° control lever Figure 10 Figure 7 Drop operation Figure 11 Lift the pull rod with one hand to activate the drop and then press down on the bed section to achieve the effect of the drop pressure.
- Page 9 EL08F Premium Chiropractic Table Please make sure that there are no objects in the space under the table before any operation. OPERATION The table should be placed at the lowest level to reduce the risk of injury caused by the patient Connect the bed to an electrical outlet using the power falling off the table when unattended.
- Page 10 Adjusting head plate width Adjustment of front bed angle As shown in Figure 7, pull the control lever Lift up the pull rod to release the angle to adjust the width of the head plates. adjustment.(Figure 11) control lever Pull rod Figure 11 Figure 7 Drop Operation...
- Page 11 EL08FS Stationary Chiropractic Table Adjusting head angle and head drop operation OPERATION ● Lift up the pull rod ① in Figure 4 to adjust head plate angle. Connect the bed to an electrical outlet using the power cord. ● Lift up the pull rod ② in Figure 4 to activate Moving and adjusting the table head plate drop section.
- Page 12 Pull rod Figure 6 Figure 9 Adjusting angle of bed middle section Drop tension adjustment Lift up the pull rod to release the angle adjustment. (Figure 10) Use the black knob on the side as indicated below. Tension direction is indicated on the knob.(Figure 7) Figure 7 Adjustment of bed tail section angle...
-
Page 13: Troubleshooting
Legend to symbols and information on the product - Check and clean the gas struts label. - Check and tighten screws (if necessary). - Model: Product identification. - Grease the parts with friction. - Model Num.: Product version. - Check the conditions of the electrical wiring and the socket. -
Page 14: Shutdown Procedure
TRANSPORTATION AND STORAGE CONDITION Transport condition The products can be transported by general means of transportation. They should be protected from the sun and rain, and should not be mixed with toxic, harmful and corrosive materials. Storage The packed electric multifunctional physiotherapy bed should be stored in a dry and well ventilated environment without corrosive gas. - Page 16 JF-EMN-2022V.01 www.coinfycare.com...