Stanton T.8O Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Stanton Manuals
  4. Turntable
  5. T.8O
  6. Operating instructions manual

Stanton T.8O Operating Instructions Manual

Direct drive turntable
Hide thumbs

Advertisement

Table of Contents

FULL MANUAL

OPERATING INSTRUCTIONS

DIRECT DRIVE TURNTABLE
T.8O
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

Advertisement

Table of Contents
loading

Related Manuals for Stanton T.8O

Summary of Contents for Stanton T.8O

  • Page 1: Operating Instructions

    FULL MANUAL OPERATING INSTRUCTIONS DIRECT DRIVE TURNTABLE T.8O WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 1. Read these Instructions – All the safety and operating instructions should be read before this product is operated. 2. Keep these Instructions – The safety and operating instructions should be retained for future reference. 3. Heed all Warnings – All warnings on the appliance and in the operating instructions should be adhered to. 4.
  • Page 3 IMPORTANT SAFETY INSTRUCTIONS 21. Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
  • Page 4 Your cartridge is to be mounted into the headshell as pre the mounting instructions included with the cartridge. The Stanton 500,680 and 890 series of cartridges require the use of the two screws mounting into the headshell. For your convenience, some of these products can be purchased already mounted and pre-adjusted from your local Stanton dealer.

  • Page 5: Part Names And Functions

    PART NAMES & FUNCTIONS 1) REVERSE This button is used to reverse the direction of the platter rotation. 2) START/STOP Press this button to start or stop the platter. 3) STROBE DOTS The dots around the edge of the platter are used in conjunction with the light located inside the motor ON/OFF switch.
  • Page 6 PART NAMES & FUNCTIONS 8) TARGET LIGHT BASE Insert target light to the deck and it will light up. 9) KEY LOCK Press to enable Key Lock. When Key Lock is on, the pitch slider will only affect the speed of the platter. The key (tone) will remain at 0%.

  • Page 7: Specifications

    PART NAMES & FUNCTIONS 20) PHONO/LINE SWITCH Note: Key Lock and Digital output processing is only available when the LINE output is used. 21) DIGITAL OUT Use this output to connect your T.80 to any SPDIF in equipped digital device. 22) POWER CORD CONNECTOR Used to connect the included power cord.
  • Page 8 SPECIFICATIONS GENERAL SECTION: Power Supply Power Consumption Dimensions Weight AC 100V, 50/60Hz (For Japan) AC 110V, 60Hz (For Taiwan) AC 120V, 60Hz (For U.S.A.,Canada,Mexico) AC 220V, 50Hz (For United Arab Emirates,Chile,Argentina) AC 220V, 60Hz (For Philippines) AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel) AC 240V, 50Hz (For Australia,U.K.) 10 Watts 452 (W) x 370 (D) x 86 (H) mm...

  • Page 9: Warranty

    Any returns to a non-authorized dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth above will void this warranty.
  • Page 10 c u t a l o n g d o t t e d l i n e...
  • Page 11 Stanton Magnetics, Inc. 3000 SW 42nd Street Hollywood, FL 33312 U.S.A. PLACE STAMP HERE...

This manual is also suitable for:

T.80

Table of Contents