Sony PDW-F355L Operating Instructions Manual page 169

Message Meaning and action to take
Run Salvage Salvage processing needs to be
done on the disc. To record on the
disc, eject the disc, insert it again,
and execute salvage processing.
Salvage processing failed. For
Salvage NG
details, see "Handling of Discs
When Recording Does Not End
Normally (Salvage Function)" on
page 50.
REC INHI.! The Write Inhibit tab of the disc is
in the recording disabled position,
or salvage processing needs to be
done on the loaded disc. Set the
tab to the recording enabled
position. Or eject the disc, insert it
again, and perform salvage
processing.
HD 50I/25P The loaded disc has a different
HD 60I/30P recording format. Exchange the
HD 23P Disc disc, or change the recording
525/60 format.
625/50
2CH×16 Clip
4CH×16 Clip
Index File! There is an unsupported index file
on the disc to which you are trying
to record. Exchange or format the
disc.
File System There is an unsupported file
system on the disc to which you
are trying to record. Exchange or
format the disc.
a) Disc operations are not possible
KEY INHI.!
when the DC IN connector is not
connected and the CA-755 is
being used.
ILL. PLAY! An A/V phase error occurred
during playback. Stop the disc.
Lid Closed! The lid of the disc compartment
does not open. Check the lid.
Lid Open! The lid of the disc compartment is
not closed. Close it securely.
No Clip! There are no clips recorded on the
disc. Exchange for a recorded
disc.
No Disc! There is no disc loaded. Insert a
disc and try the operation again.
STOP ONCE! The operation is not possible while
REC mode! the disc is being played or
recorded. Stop the disc.
Disc Top! The operation is not possible
Disc End! because the disc is at the top or
end.
Formatting! The disc is being automatically
formatted. Wait until the format
ends.
Recording The unit is writing to the file
system. Wait until writing finishes.
Message Meaning and action to take
No EM Space Essence marks cannot be
inserted. For details, see
EM Full!
"Recording Shot Marks" on
page 65.
SB CLP mode Press the SEL/SET button (four-
way arrow key) up to clear the
SUB CLIP indicator before
carrying out the operation.
No SEL List No clip list is selected. Create a
new clip list, or load a clip list from
the disc.
No List! There is no clip list. Create a clip
list.
No SUB Clip There are no sub clips in the clip
list. Register a sub clip, or load
another clip list.
SUB Clip NG The In and Out point positions are
invalid. Set correct In and Out
points.
MAX# SB CLP The total number of sub clips is
over the upper limit (300).
CL OVER DUR The total duration of sub clips in
the current clip list is over the
upper limit (24 hours).
FAN Stopped The main unit or drive fan has
DR-FAN Stop stopped. Avoid use under high
temperatures, turn off the power,
and contact your Sony dealer.
a) REC INHI.! appears if you attempt to start recording.
Alarm messages during thumbnail search,
scene selection, and clip list operations
Alarm messages may appear in the LCD monitor during
thumbnail search, scene selection, and clip list operations.
In this case, take the action indicated in the following table.
Message Meaning and action to take
CANNOT EXPAND The clip cannot be expanded into
CLIP ANY FURTHER. more blocks.
This appears when the EXPAND
button is pressed when the
number of block is maximum, or
when the duration of an expanded
thumbnail is 1 frame.
SELECTED ESSENCE The selected essence mark does
MARK DOES NOT not exist.
EXIST. This appears in the essence mark
selection screen when the
specified essence mark does not
exist on the disc.
SUB CLIP IS INVALID. The temporal relationship between
SET APPROPRIATE the specified In and Out points in a
TRIM operation (see page 93) is
IN/OUT POINTS.
not correct.
Reset so that the value of the Out
point timecode is larger than the
value of the In point timecode.
169
Operation Warnings