Heat & Glo NorthStar-BK Installation Manual page 15

F. Protective Metal Hearth Strips
WARNING! Risk of Fire!
strips MUST be installed on combustible surfaces. DO
NOT cover metal strips with combustible materials.
Sparks or embers may ignite flooring.
WARNING! Risk of fire!
embers or other burning material falling from the
fireplace may ignite flooring or concealed combustible
surfaces.
• Protective metal hearth strips MUST be installed.
• Hearth extensions MUST be installed exactly as
specified.
• o ate t e t o ote tive etal ea t st i s easu in
a o i atel 26 in
it t is e la e
• Sli e ea etal st i 2 in 51
e la e
• Ove la st i s in t e
25 ini u
• Metal st i s ust e ten
o t e e la e o enin
i u e 3
• ote t t e ont o a lat o
e tension it etal st i s not in lu e
e i u e 3 8 See
inst u tions
P a l l e t M o u nt ing /F l o o r
B r a c k e t s
M e t a l s t r ip s 2 in. ( 5 1
a nd H e a r t h E x t e ns io n a nd
b e y o nd b o t h s id e s o f f ir e p l a c e o p e ning .
N a il o r s c r e w m e t a l s t r ip s in p l a c e .
Figure 3.7 Position the Protective Metal Hearth Strips
T o p p ie c e m u s t o v e r l a p
R a is e d P l a t f o r m
2 in.
( 5 1 m m )
2 in.
( 5 1 m m )
Figure 3.8 Protect the Front of an Elevated Platform
Heat & Glo • NORTHSTAR • 480-2360 Installation Manual • Rev D • 05/30/13
All manuals and user guides at all-guides.com
Protective metal hearth
High temperatures, sparks,
4 in 660 102 in lu e
un e ont e
i le o e la e o enin
e on t e ont an si es
at least 2 in 51
elevate a ove t e ea t
it
Se tion 6 o ea t e tension
1 in. ( 25 m m ) O v e r l a p
m m ) u nd e r e d g e o f F ir e p l a c e
e x t e nd e d 2 in. ( 5 1
b o t t o m p ie c e
1 in. ( 25 m m ) m in.
o v e r l a p
F l o o r
G. Facing Material
WARNING! Risk of Fire!
Follow these instructions exactly.
Facing materials must be installed properly to prevent
fire.
No materials may be substituted without authorization by
Hearth & Home Technologies
TOOLS NEEDED:
aul in un
Onl non- o
a e use to ove t e
NOTE: All boards are pre-drilled for your convenience.
Boards MUST be attached in the following order:
bottom, top, and then the two sides, red-painted side
out. The top and bottom board should each have a hang
tag attached. Leave them attached for referral for the
finishing operation.
e o
• Atta t e otto
e la e an it en lose s e s ensu in t e oa
1 in
is ente e
• ente an atta
a in
• sin t e Su e
ini u
an t e utt e
e la e
• nsu in t e to o t e si e ie es an t e to
ali n atta
e e s
►
NOTICE:
after finishing materials are applied. This 1/8 in. must
be painted or the red will show.
Top
Board
m m )
Side
Board
Bottom
Board
Figure 3.9
o e e ill it
usti le ate ials su
etal e la e ont
oa to t e otto
DO NOT remove hang tags
t e to oa to t e oute
e e s
DO NOT remove hang tags.
alsti un a li
et een t e etal su a e o t e
es o t e to oa
t e si e ie es to t e oute an an
1/8 in. of the facing material may be visible
DO NOT
Side
remove hang
Board
Apply Non-combustible Materials
2 illi s ea it
lie it e la e
o t e oute
an an
t ea 1/8 in
e la e
See i u e 3
oa
a in
Apply bead of
Super Calstick to
edge here
tags
15