Flymo EasiLife Operator's Manual page 23

3.10.4.2 To set the LawnSense frequency
Set how frequently the product cuts the grass when
LawnSense is in use. There are 3 frequency levels:
the
Low, Mid and High . The higher the frequency, the more
sensitive the product is to the grass growth. That is, if
the grass growth is high then the product is allowed to
work longer.
Note:
If the mowing results are not optimal when
LawnSense , the schedule settings may need
using
adjusting. Do not restrict the schedule more than
necessary. Also, check that the blade disc is clean and
that the blades are in good condition.
To get access to the menu on
1. Do steps 1–3 in
page 21 .
2. Use the arrow buttons and the OK button to move
through the menu structure
time .
3. Use the arrow buttons to select
frequency.
4. Push the BACK button.
3.10.5 Security level
Function Low
PIN-code
Time lock X
PIN-code - The correct PIN-code must be entered
•
to get access to the Menu structure of the product.
If the incorrect PIN-code is entered 5 times, the
product is locked for a time. The lock is extended
for each new incorrect try.
• Time lock - The product locks if the PIN-code has
not been entered in 30 days. Enter the PIN-code to
get access to the product.
3.10.5.1 To set the security level
Select 1 of the security levels for your product.
1. Do steps 1–3 in To get access to the menu on
page 21 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Security level .
3. Use the arrow buttons and the OK button to select
the level of security.
4. Push the OK button.
1392 - 007 -
3.10.5.2 Security - Advanced
To make a new loop signal
The loop signal is randomly selected to create a unique
link between the product and the charging station. In
rare cases, there may be a need to make a new
signal, for instance if two adjacent installations have
very similar signals.
1.
2.
3.
4.
To change the PIN-code
LawnSense > Cutting
1.
Low, Mid or High
2.
3.
4.
5.
6.
7.
High
3.10.6 Lawn Coverage and PassageSense
X
If the work area includes remote parts that are
connected with narrow passages, the
X
and
maintain a well-cut lawn in all parts of the yard. The
Lawn Coverage function is used to guide the product
to remote parts of the work area. The
function is used for narrow passage mowing. A guide
wire must be installed to use these functions. You can
set a maximum of 3 remote areas.
With the
follows and then leaves the guide wire after a certain
distance and starts to mow the lawn.
The
passages of 60 cm - 1.5 m / 23 in. - 4.9 ft. width.
The product moves in a pattern to cover the passage
width. The product starts the
distance from the charging station. When the product
reaches the end of the narrow passage, the product
Settings > Security >
continues and cuts the lawn as normal.
Area A, approximately 50%
Area B, approximately 30%
Area C, approximately 20%
Put the product in the charging station.
To get access to the menu on
Do steps 1–3 in
page 21 .
Use the arrow buttons and the OK button to move
Settings > Security >
through the menu structure
Advanced > New loop signal .
Wait for confirmation that the loop signal has been
made. This usually takes about 10 seconds.
To get access to the menu on
Do steps 1–3 in
page 21 .
Use the arrow buttons and the OK button to move
through the menu structure Settings > Security >
Advanced > Change PIN-code .
Enter the new PIN code.
Push the OK button.
Enter the new PIN code again.
Push the OK button.
Make a note of the new PIN code. Refer to
Introduction on page 3 .
PassageSense function are useful to be able to
Lawn Coverage function the product first
PassageSense function is suitable to mow narrow
PassageSense at the set
Lawn Coverage
PassageSense
Installation - 23