Bosch GBM 13-2 RE Professional Original Instructions Manual page 7

a)
(15) Universal bit holder
(16) Securing screw for keyless/keyed chuck
b)
(17) Open-ended spanner
a)
(18) Clamping sleeve
a)
(19) Securing ring
a)
(20) Holding ring
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
b) Commercially available (not included in the scope of deliv-
ery)
Technical data
Drill
Article number
Rated power input
Max. power output
No-load speed
– First gear
– Second gear
Rated speed
– First gear
– Second gear
Rated torque (1st/2nd gear)
Spindle collar diameter
Speed preselection
Speed control
Right/left rotation
Overload clutch
Keyless chuck with securing
ring
Keyless chuck
Keyed chuck
Max. drilling diameter (1st/2nd gear)
– Steel
– Wood
– Aluminium
Chuck capacity
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Bosch Power Tools
Auxiliary handle (see figure A)
u
You can adjust the auxiliary handle (9) to any of 12 positions
in order to achieve a safe work posture that minimises fa-
tigue.
Turn the lower gripping end of the auxiliary handle (9) in ro-
tational direction ➊ and push the auxiliary handle (9) for-
ward until you can swivel it into the required position. Then
pull the auxiliary handle (9) back again and turn the lower
gripping end in rotational direction ➋ to tighten it.
Setting the drilling depth (see figure A)
You can use the depth stop to set the required drilling depth
X.
GBM 13-2 RE
Turn the lower gripping end of the auxiliary handle (9) anti-
3 601 AB2 0..
clockwise and set the depth stop (10).
W 750
Pull the depth stop (10) far enough out that the distance
W 353
between the drill bit tip and the edge of the depth stop (10)
corresponds to the required drilling depth X.
Then, turn the lower gripping end of the auxiliary handle (9)
-1
min 0–1000
clockwise to retighten it.
-1
min 0–3000
The fluting on the depth stop (10) must face upwards.
Changing the tool
-1
min 500
-1
min 1750
u
Nm 6.8/2.5
u
mm 43
●
●
Keyless chuck (see figure B)
●
Hold the rear sleeve (3) of the keyless chuck (1) firmly and
●
turn the front sleeve (2) in rotational direction ➊ until the
tool can be inserted. Insert the tool.
–
Hold the rear sleeve (3) of the keyless chuck (1) and firmly
tighten the front sleeve (2) by hand in rotational direction ➋
●
until you hear a click. This will automatically lock the drill
–
chuck.
The lock will disengage again if you turn the front sleeve (2)
in the opposite direction to remove the tool.
mm 13/8
mm 32/20
Keyed chuck (see figure C)
Open the keyed chuck (13) by turning it until the tool can be
mm 20/12
inserted. Insert the tool.
mm 1.5–13
Insert the chuck key (12) into the corresponding holes of the
kg 2.4
keyed chuck (13) and clamp the tool evenly.
Keyless chuck with securing ring (see figure D)
/ II
Turn the securing ring (19) in the "UNLOCK" direction.
Turn the clamping sleeve (18) clockwise until the applica-
tion tool can be inserted.
Fully insert the application tool, hold it in the tool holder and
turn the clamping sleeve (18) anticlockwise firmly by hand
to tighten it. When doing so, hold the holding ring (20) firmly
in place.
Turn the securing ring (19) in the "LOCK" direction.
Do not operate your power tool without the auxiliary
handle (9).
Pull the plug out of the socket before carrying out any
work on the power tool.
Wear protective gloves when changing tools. The drill
chuck may heat up significantly when it is used for long
periods.
160992A68G | (21.07.2021)
English | 7