HP Z Turbo Drive Quad Pro Installation Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Computer Hardware
  5. Z Turbo Drive Quad Pro
  6. Installation manual

HP Z Turbo Drive Quad Pro Installation Manual

Hide thumbs Also See for Z Turbo Drive Quad Pro:
Table of Contents

Advertisement

Quick Links

HP Z Turbo Drive Quad Pro installation
Printed in
*838785-002*
838785-002

Advertisement

Table of Contents
loading

Related Manuals for HP Z Turbo Drive Quad Pro

Summary of Contents for HP Z Turbo Drive Quad Pro

  • Page 1 HP Z Turbo Drive Quad Pro installation Printed in *838785-002* 838785-002...
  • Page 2 The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

  • Page 3: Kit Contents

    HP Z Turbo Drive Quad Pro installation Introduction This document describes how to install the HP Z Turbo Drive Quad Pro into the HP Z440, Z640, and Z840 series workstations. Kit contents ● HP Z Turbo Drive Quad Pro ●...

  • Page 4: Warnings And Cautions

    NOTE: HP accessories are for use in HP computer products. They have been extensively tested for reliability and are manufactured to high quality standards. Installing additional M.2 modules in the HP Z Turbo Drive Quad You can install up to four M.2 PCIe SSD modules in this drive.
  • Page 5 While holding the right latch, press the center of the edge of the cover and lift it (3). Loosen the two captive screws on the heat sink (1). Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro...
  • Page 6 Lift the heat sink to expose the M.2 modules (2). NOTE: The drive comes with at least two M.2 modules preinstalled. Remove the standoff from the next M.2 slot. HP Z Turbo Drive Quad Pro installation...
  • Page 7 Insert standoff into the curve of the right edge of the M.2 module. Slide the M.2 module into the connector (1) and then press down until the standoff is aligned with the embedded nut (2). Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro...
  • Page 8 Screw the standoff into the nut. Reinstall the heat sink (1) and tighten the captive screws (2). Be sure that the tabs on the heat sink are under the metal pins and can rotate. HP Z Turbo Drive Quad Pro installation...
  • Page 9 Close the cover (1) and slide the left latch to the right until no red is showing (2). Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro...

  • Page 10: Accessing The Internal Components Of The Computer

    HP Z Turbo Quad Pro ● For configuration instructions, see Installing multiple HP Z Turbo Drives or HP Z Turbo Quad Pro Drives on page Press down on the two green PCI retention clips (1) located inside the workstation until they release, and then rotate them down to raise the retention clamp (2).
  • Page 11 LED cable to the HDD LED connector on the system board. NOTE: To locate the HDD LED connector on the system board, see the System Board Overview on the service panel. Installing the drive in an HP Z440 Workstation...
  • Page 12 HP Z Turbo Quad Pro For configuration instructions, see Installing multiple HP Z Turbo Drives or HP Z Turbo Quad Pro Drives on page Press down on the two green PCI retention clips located on the rear of the chassis (1) until they release, then rotate the clips down to raise the retention clamp from the slot covers (2).
  • Page 13 LED cable to the HDD LED connector on the system board. NOTE: To locate the HDD LED connector on the system board, see the System Board Overview on the service panel. Installing the drive in an HP Z640 Workstation...
  • Page 14 HP Z Turbo Quad Pro For configuration instructions, see Installing multiple HP Z Turbo Drives or HP Z Turbo Quad Pro Drives on page Squeeze the two green tabs together to release the retainer (1), rotate the PCI retainer (2) up, and lift it out of the chassis (3).
  • Page 15 LED cable to the HDD LED connector on the system board. NOTE: To locate the HDD LED connector on the system board, see the System Board Overview on the service panel. Installing the drive in an HP Z840 Workstation...
  • Page 16 A second HP Z Turbo Quad Pro can be installed on an HP Z840 with a second CPU only. The HP Z Turbo Drive and HP Z Turbo Drive G2 both support a single M.2 module and have jumpers that can be set to eight unique addresses.
  • Page 17 HP Z Turbo Drive solutions. If using a combination of solutions, HP recommends using Address C or Address D for the HP Z Turbo Drive Quad Pro and Address 0, Address 1, Address 2, or Address 3 for the HP Z Turbo Drive solution.

  • Page 18: Completing The Installation

    To configure the LED cables on a system with an HP Z Turbo Drive Quad Pro and an HP Z Turbo Drive: Connect an LED cable to the HDD activity header on the HP Z Turbo Drive that is marked HDDACT1.

Table of Contents