Table of Contents
Advertisement
Roll-A-Door
Series 2 installation instructions
®
1.2 substrate fastener recommendations
WARNING! Coach bolts/
screws are NOT suitable
for windrated doors.
Refer
to High Wind drawings on
the B&D Website.
WARNING! The installer
must
select
and
fasteners appropriate to
the material into which
they are being fixed.
important notes
a) For installation to materials
not covered in the chart,
the installer should seek
expert
advice
from
qualified builder.
b) Minimum length of fastener
does not exclude use of
longer
lengths.
Decision
must be made by fitter to
ensure adequate strength.
c) Recommendations for old
materials or materials not
in good condition are not
included. If in doubt about
the strength of the material
seek specialist advice.
d) Fasteners for brackets in
masonry should be at least
8mm x 75mm long or metric
equivalent.
e) Use the washers supplied in
the parts bag to all fixings.
BRICK
CONSTRUCTION
masonry
anchors
(minimum
bolt size
12mm x
55mm)
MASONRY BLOCK
CONSTRUCTION
long bolts
steel plate
Fig: 2.1.1
material
New Solid Brick
use
New Hollow Brick
New Solid Concrete
a
Steel Framing
e.g. BHP Framing
(with rear access)
Heavy Gauge Steel
Light Steel Framing
e.g. BHP House
Framing
(no rear access)
New Timber
STEEL CONSTRUCTION
weld
left hand
bracket
WARNING! Masonry blockwork should be properly filled and reinforced if
brackets are to be mounted directly to blockwork with masonry anchors.
Where the blockwork is not solidly filled but structurally sound, long bolts
should be passed through the blockwork using suitable steel plates
under bolt heads.
Special consideration should be given to brick type and construction
of wall, to ensure satisfactory fixing e.g. welding detail if fixed to steel.
right hand
bracket
fastener type(s)
Coach Bolts (Hex Lag Screw) and
washers - combined with wall plugs
Macplugs (wall plugs) to suit above
HLC Sleeve Anchors (Dyna Bolts)
with washers
Screw Masonry Flange Hex Head
(M8 x75)
Coach Bolts (Hex Lag Screw) and
washers - combined with wall plugs
Macplugs (wall plugs) to suit above
HLC Sleeve Anchors (Dyna Bolts)
with washers
Hex Head Bolt Zinc Plated,
Hexagon Nuts Zinc Plated,
Washers Zinc Plated
Hex Head Tek and washers
Heavy Duty Kap Toggle
Hex Head Tek and washers
Coach Bolts (Hex Lag Screw) and
washers
Hex Head Tek and washers
right
hand
bracket
bolt
guides
to steel
work
length of
diameter
fastener
or type
(see note)
5/16"
x
50mm
5/16"
x
80mm
5/16"
x
50mm
5/16"
x
80mm
12mm
x
55mm
8mm
x
75mm
5/16"
x
50mm
5/16"
x
80mm
5/16"
x
50mm
5/16"
x
80mm
12mm
x
55mm
5/16"
x
1"
3/8"
x
1"
10mm
x
25mm
12mm
x
25mm
14-20
x
22mm
10mm
x
100mm
12mm
x
100mm
6-10
x
20mm
5/16"
x
50mm
5/16"
x
80mm
14-10
x
50mm
SECURE GUIDE
coach
screws
into
masonry
plugs
4
BKT
GUIDE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Advertisement
Table of Contents
