1. Manuals
  2. Brands
  3. Cleveland Manuals
  4. Commercial Food Equipment
  5. SPLASH PROOF SET-10
  6. Operator's manual

Cleveland Set-10 Operator's Manual

Skillet
Hide thumbs Also See for Set-10:
Table of Contents

Advertisement

Quick Links

Download this manual
All manuals and user guides at all-guides.com
Operators Manual
Installation, Operation & Service
Skillets
TABLE TOP ELECTRIC
SKILLETS-
MODELS:
SET-10
SET-15
SET-15
SET-10
™
Cleveland
1333 East 179th St., Cleveland, Ohio, U.S.A. 44110
Phone: (216) 481-4900 Fax: (216) 481-3782
Visit our web site at www.clevelandrange.com
Enodis
SE95031 rev. 4

Advertisement

Table of Contents
loading

Related Manuals for Cleveland Set-10

Summary of Contents for Cleveland Set-10

  • Page 1 Installation, Operation & Service Skillets TABLE TOP ELECTRIC SKILLETS- MODELS: SET-10 SET-15 SET-15 SET-10 ™ Cleveland 1333 East 179th St., Cleveland, Ohio, U.S.A. 44110 Phone: (216) 481-4900 Fax: (216) 481-3782 Visit our web site at www.clevelandrange.com Enodis SE95031 rev. 4...

  • Page 2: For The User

    THE INSTALLATION AND CONNECTION MUST COMPLY WITH THE LOCAL AND NATIONAL ELECTRICAL CODES. ENSURE ELECTRICAL SUPPLY CONFORMS WITH ELECTRICAL CHARACTERISTICS SHOWN ON THE RATING LABEL ALL SERVICE MUST BE PERFORMED BY A QUALIFIED CLEVELAND RANGE TECHNICIAN. RETAIN THIS MANUAL FOR YOUR REFERENCE.

  • Page 3: General Information

    All manuals and user guides at all-guides.com INSTALLATION GENERAL INFORMATION INSPECTION / UNPACKING These instructions must be retained by the owner/user 1. Before unpacking visually inspect the unit for for future reference. evidence of damage during shipping. The serial plate is located on the right side of the control 2.

  • Page 4: Installation Clearances

    SET-15 - RIGHT: 4”, LEFT: 4”, REAR 1/2” ELECTRICAL CONNECTION INSTALLATION SET-10: Remove the screw at the rear of the console 1. Carefully remove unit from carton or crate. Remove cover, and remove the cover. A wiring diagram is affixed any packing material from unit.
  • Page 5 All manuals and user guides at all-guides.com OPERATING INSTRUCTIONS TEMPERATURE APPLICATION CHART 1. Ensure that the electrical supply to the skillet is turned on. Approximate 2. Before cooking, be sure that the skillet's cooking Dial Temperature surface is clean, and that the skillet is in the fully Application °F °C...

  • Page 6: Cleaning Instructions

    All manuals and user guides at all-guides.com CLEANING INSTRUCTIONS CLEANING INSTRUCTIONS CAUTION 1. Turn unit off. SURFACES MAY 2. Prepare a warm water and mild detergent solution in BE EXTREMELY HOT! the unit. 3. Remove food soil using a nylon brush. CARE AND CLEANING 4.
  • Page 7 All manuals and user guides at all-guides.com STAINLESS STEEL EQUIPMENT CARE AND CLEANING (Supplied courtesy of Nafem. For more information visit their web site at www.nafem.org) Contrary to popular belief, stainless steels ARE susceptible to rusting. 4. Treat your water. Corrosion on metals is everywhere.

  • Page 8: Service Parts

    FBS-SET15T for SET-15 ..... 1 FBS-SET10T for SET-10 ..... 1 KE50825-6 3/4"...
  • Page 9 All manuals and user guides at all-guides.com MODEL SET-10 SKILLET BOTTOM (for units built prior to August 2007) Tighten to 11 ft-lb & apply locktite ITEM NO. PART NO. DESCRIPTION QTY. SK2231500 SPHERICAL WASHER ..........16 FA21024 5/16-18 HEX.
  • Page 10 All manuals and user guides at all-guides.com MODEL SET-10 SKILLET BOTTOM (for units built after August 2007) Tighten to 11 ft-lb & apply locktite ITEM NO. PART NO. DESCRIPTION QTY. SK00008 PAN WELDMENT ..........1 FA11145 10/32X3/8 CROSS HEAD SCREW .
  • Page 11 All manuals and user guides at all-guides.com MODEL SET-10 CONTROL HOUSING DRAWING (for units prior to August 2007) ITEM NO. PART NO. DESCRIPTION QTY. SCREW, COVER, 10 - 24 X'/2" ........1 SK2234200 SPRING .
  • Page 12 All manuals and user guides at all-guides.com MODEL SET-10 ASSEMBLY DRAWING (for units built after August 2007) 5C 5D...
  • Page 13 All manuals and user guides at all-guides.com MODEL SET-10 ASSEMBLY DRAWING (for units built after August 2007) ITEM NO. PART NO. DESCRIPTION QTY. SK2238099 TILT STOP SHAFT ASS'Y ......... .1 SK2238200 COMPONENT PLATE .
  • Page 14 All manuals and user guides at all-guides.com MODEL SET-15 SKILLET MARINE LOCK BOTTOM & COVER VENT CAP ITEM NO. PART NO. DESCRIPTION QTY. SK2211500 Screw, 1/4”-20 x 3/8" ..........1 FA30505-1 Washer .
  • Page 15 All manuals and user guides at all-guides.com MODEL SET-15 SKILLET CONTROL HOUSING (for units built prior to November 2005) ITEM NO. PART NO. DESCRIPTION QTY. SK2274900 Cover, Control Box ..........1 KE54846-3 Gasket, Control Box Cover .
  • Page 16 All manuals and user guides at all-guides.com MODEL SET-15 SKILLET CONTROL HOUSING (for units built after November 2005) SECTION C-C PLACE ITEM #13 BETWEEN ITEM #1 AND ITEM #7, 2 PLACES DETAIL NOT SHOWN ON THIS DRAWING. ITEM NO. PART NO. DESCRIPTION QTY.
  • Page 17 All manuals and user guides at all-guides.com MODEL SET-15 BASE/PAN ASSEMBLY (for units built after November 2005) ITEM NO. PART NO. DESCRIPTION QTY. KE000851 BASE WELDMENT ..........1 SK00348 SUPPORT BAR ASS'Y, L.H.

  • Page 18: Servicing Guide

    All manuals and user guides at all-guides.com MAINTENANCE SERVICING GUIDE This section contains servicing information intended for use by Authorized Service Personnel. PROBLEM: Skillet fails to heat with pilot light on. Probable Cause Test and Remedy Faulty contactor(s) Check coil(s) and contacts of contactor(s). Replace if necessary. Faulty wiring Check wiring to contactor(s).
  • Page 19 All manuals and user guides at all-guides.com HEATING ELEMENT HEATING ELEMENT BLOCK REMOVAL TORQUING 1. Tilt the skillet forward to access bottom cover plate. Uneven torquing of heating element block retaining plate nuts may cause uneven heating of 2. Make sure power switch and external circuit breaker the cooking surface.
  • Page 20 All manuals and user guides at all-guides.com WIRING DIAGRAM, SET-10 & SET-15 (for units built prior to November 2005) 208, 220 or 240V, Single or Three Phase...
  • Page 21 All manuals and user guides at all-guides.com WIRING DIAGRAM, SET-10 & SET-15 (for units built prior to November 2005) 208/380 or 240/415V, Three Phase Y Connected...
  • Page 22 All manuals and user guides at all-guides.com WIRING DIAGRAM, SET-10 & SET-15 (for units built prior to November 2005) 480V, Single or Three Phase...
  • Page 23 All manuals and user guides at all-guides.com WIRING DIAGRAM, SET-10 & SET-15 (for units built after November 2005) 208, 220 or 240V, Single or Three Phase...
  • Page 24 All manuals and user guides at all-guides.com WIRING DIAGRAM, SET-10 & SET-15 (for units built after November 2005) 208/380 or 240/415V, Three Phase Y Connected...
  • Page 25 All manuals and user guides at all-guides.com WIRING DIAGRAM, SET-10 & SET-15 (for units built after November 2005) 480V, Single or Three Phase...

This manual is also suitable for:

Set-15

Table of Contents