The AEL (accessible emission level )of the laser power output is less than CLASS 1 but the laser component is capable of emitting radiation exceeding the limit for CLASS 1. A specially instructed person should do servicing operation of the apparatus. DEH-X7600S/XNUC...
Page 3
CAUTION Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Discord used batteries according to the manufacturer's instructions. DEH-X7600S/XNUC...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. DEH-X7600S/XNUC...
2. SPECIFICATIONS 2.1 SPECIFICATIONS DEH-X7600S/XNUC MP3 decoding format ..MPEG-1 & 2 Audio Layer 3 WMA decoding format ..Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch General audio) Power source ....14.4 V DC (10.8 V to 15.1 V al-...
Page 7
MP3 decoding format ..MPEG-1 & 2 Audio Layer 3 WMA decoding format ..Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch Note audio) Specifications and the design are subject to (Windows Media Player) modifications without notice. DEH-X7600S/XNUC...
Securing the front panel The front panel can be secured with the supplied screw. Screw (BPZ20P060FTC) (UC) (XXX7020) (GS, GS1, CS, ID) 2.2 DISC/CONTENT FORMAT DEH-X7600S/XNUC...
Distortion Noise Volume too low Volume too high Volume fluctuating Sound interrupted 3.2 PCB LOCATIONS CD Core Unit (S11.6STD) Tuner Amp Assy Keyboard Unit A:DEH-X7600S/XNUC B:DEH-X7650SD/XNGS C:DEH-X7650SD/XNGS1 D:DEH-X7650SD/XNCS E:DEH-X7690SD/XNID Unit Number QWM3777(A) Unit Number QWM3778(B,C) Unit Number Unit Number QWM3779(D)
CD Mechanism Module 3.4 CLEANING Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DEH-X7600S/XNUC...
FCO- Q772 SPINDLE MOTOR SPO- LDIN LOEJ SPO+ LCOM SLLDO- CLCONT VDD33 LOADING/CARRIAGE LCOP MOTOR SLLDO+ MUTE CONT RESET RESET DSCSNS RESET CDRST HOME SD _ CD S903 S901 CD DATA (CDSRQ,CDSTBY,SKIP, CD DATA (CDSRQ,CDSTBY,SKIP,SCL,SDA, DSCSNS HOME SCL,SDA,DATA,BCLK,LRCK,WAIT) DATA,BCLK,LRCK,WAIT) DEH-X7600S/XNUC...
In case of the above signal, the communication Source keys with Grille microcomputer may fail. operative If the time interval is not 500 msec, the oscillator may be defective. Source ON SYSPW<-H Pin 36 Completes power-on operation. (After that, proceed to each source operation) DEH-X7600S/XNUC...
: Servo-related errors CD Off, Eject, ACC Off, Back-up Off, Communication reset, Reset Load NG/Eject NG(50) : Reload, Eject, ACC Off, Back-up Off, Communication reset, Reset Failure in retried turning for ejection : CD On, Eject, ACC Off, Back-up Off, Communication reset, Reset DEH-X7600S/XNUC...
Page 17
USB storage de- songs. the iPod. vice consumes vice and do not more than maxi- use it. Turn the mum allowable ignition switch to current. OFF, then to ACC or ON and then connect only compliant USB storage devices. DEH-X7600S/XNUC...
Page 18
BAND key to failed. pear on the Station found. in the Pandora retry. screen. application on your iPhone. Start up and The application Follow the in- play your has not started structions that ap- Application. running yet. pear on the screen. DEH-X7600S/XNUC...
Page 19
The channel Check the contact your deal- able that you have SiriusXM channel er or an author- requested is not lineup. ized Pioneer a valid SiriusXM Service Station channel. for assistance. Not Sub- The channel Check the con- Check Tuner...
APP/TI + BAND key LIST key r r u All lights OFF LIST key Confirmation of image ROM connection LIST key Display of media microcomputer information LIST key Display of Manufacture_ID information LIST key UC only r r u DEH-X7600S/XNUC...
Page 22
There might be a problem in communication or abnormality in the display microcomputer. If an obviously weird numeral appears as the version: There might be a problem in communication. If the number of CHs used is not properly displayed despite the version displayed: There might be defective connection with EEPROM. DEH-X7600S/XNUC...
Page 23
0 8 16 24 32 40 48 56 64 72 80 88 96 04 12 20 28 36 44 52 60 68 76 84 92 M a n u f a c t u r e 0 x C 0 2 8 2 0 E D DEH-X7600S/XNUC...
When the power is turned on/off the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows) DEH-X7600S/XNUC...
Slide the Tuner Amp Assy in the direction of the arrow. Lift off the Tuner Amp Assy from the Heat Sink side. The Tuner Amp Assy is fixed into the ditch. Disconnect the FFC and then remove the CD Mechanism Module. CD Mechanism Module Fig.2 DEH-X7600S/XNUC...
Page 26
Tuner Amp Assy Remove the two screws. Remove the two screws and then remove the Tuner Amp Assy. Fig.3 - Attention of removing (Fig.4) Don’t remove this screws excluding the dismantlement of the CD Mechanism Module. CD Mechanism Module Fig.4 DEH-X7600S/XNUC...
Page 27
1. Attach the button from the front side of the panel. Fig.7 2. Attach the spring to the arm as shown in the figure. The bended tip of the spring is set to this side. Hitch the spring to the groove. Fig.8 DEH-X7600S/XNUC...
Page 28
4. Fit the boss on the lower side of the arm in the lower hole of the panel, and then warp the rib on the panel in the direction shown in the figure and fit the boss of the arm in the panel. Fig.9 DEH-X7600S/XNUC...
Page 29
2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion. 3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx. 8N or less) Handling OK Handling NG DEH-X7600S/XNUC...
Page 30
Fig 3 Fig 4 [Incorrect built-in state] The chassis is not nipped between Outer holder Normal built-in state the PU case and the PU rack. Rear end of feeding screw DEH-X7600S/XNUC...
1k ohms in series. The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. DEH-X7600S/XNUC...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-X7600S/XNUC...
The clock signal is output from the PCL terminal IC601 (Pin 37)(TP : PCL). The frequency of the clock signal is 625.0 kHz that is one 32th of the fundamental frequency (20 MHz). If the clock signal out of the range, the X’tal (X601) should be replaced with new one. DEH-X7600S/XNUC...
Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 9.1 PACKING X7650SD/XNGS X7650SD/XNGS1 X7650SD/XNCS X7690SD/XNID X7600S/XNUC DEH-X7600S/XNUC...
Page 37
See Contrast table (2) 14-3 Service Network See Contrast table (2) Handle QNC3021 Screw TRZ50P080FTC (2) CONTRAST TABLE DEH-X7600S/XNUC, DEH-X7650SD/XNGS, DEH-X7650SD/XNGS1, DEH-X7650SD/XNCS and DEH-X7690SD/ XNID are constructed the same except for the following: DEH-X7600S/ DEH-X7650SD/ DEH-X7650SD/ DEH-X7650SD/ DEH-X7690SD/ Mark Description...
RGB ILM DGND DGND RED KEY ZONE BLUE LCD ZONE GREEN KEY ZONE GREEN LCD ZONE BLUE KEY ZONE RED LCD ZONE Q1634 Q1635 Q1636 Q1639 Q1637 Q1640 LSCR523UB LSCR523UB LSCR523UB LSCR523UB HN1C01FU(YGR) HN1C01FU(YGR) ILMGND KEY ILM LCD ILM DEH-X7600S/XNUC...
1 V/div fRFAGC 500 mV/div 500 mV/div 500 mV/div 9TIN 500 mV/div Focus Search waveform Track Open waveform 100 Track Jump waveform (32 Track Jump x 3) Ref.: Ref.: Ref.: REFO REFO REFO Mode: Mode: Mode: TEST TEST TEST DEH-X7600S/XNUC...
Page 59
12 cm CD Eject operation 12 cm CD Eject operation Ref.: Ref.: Mode: Mode: Normal Normal 500 µs/div fRFAGC 1 V/div 9TIN 1 V/div 1 V/div aFIN 1 V/div µ Black Dot (800 m) during play Ref.: REFO Mode: Normal DEH-X7600S/XNUC...
The expression of the unit in this manual is shown by u instead of µ. Please do not make a mistake. Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. (A,106,65) IC(B,C,D,E) PEQ261A8 A:DEH-X7600S/XNUC IC 603 (A,127,46) IC S-80827CNMC-B8M B:DEH-X7650SD/XNGS IC 604 (A,101,82) IC(A)
Page 69
R 312 (A,31,130) RS1/16SS223J VA806 (B,121,22) Varistor EZJZ1V270RM R 321 (A,78,124) RS1/16SS362J VA807 (B,122,22) Varistor EZJZ1V270RM R 322 (A,79,124) RS1/16SS362J VA808 (B,120,12) Varistor EZJZ1V270RM R 323 (A,82,124) RS1/16SS362J CN751 (A,116,38) Connector VKN1192 R 324 (A,83,124) RS1/16SS362J CN802 (A,111,4) Connector CKS6452 DEH-X7600S/XNUC...
Page 70
RS1/10SR104J R 733 (A,72,93) RS1/16SS473J R 734 (A,78,90) RS1/16SS473J R 623 (B,95,50) RS1/10SR104J R 735 (A,78,87) RS1/16SS473J R 628 (A,116,68) RS1/16SS104J R 741 (A,82,56) (A) RS1/16SS101J R 631 (A,116,64) RS1/16SS104J R 632 (A,116,73) RS1/16SS472J R 742 (A,74,49) (A) RS1/16SS101J DEH-X7600S/XNUC...
Page 71
CCG1236 R 869 (B,62,45) RS1/10SR473J C 201 (A,46,118) CKSSYB104K10 R 881 (A,47,87) RS1/10SR103J C 202 (A,51,112) 22 uF CCG1254 R 882 (A,55,96) RS1/16SS473J C 204 (A,38,103) CKSSYB102K50 C 205 (A,42,104) CKSSYB104K16 R 883 (A,54,96) RS1/16SS222J R 884 (A,53,90) RS1/16SS222J DEH-X7600S/XNUC...
Page 72
C 413 (A,137,97) CKSSYB103K16 C 662 (A,86,64) CCSSCH120J50 C 414 (A,135,98) 10 uF CCG1192 C 415 (A,134,98) (A,B,C,D) CCSSCK2R0C50 C 663 (B,81,67) CKSRYB104K16 C 416 (B,134,85) (A) CCSRCK2R0C50 C 664 (A,57,65) (B,C,D,E) CCSSCH100D50 (B,134,85) (B,C,D) CCSRCH101J50 C 665 (B,59,66) CKSRYB104K16 DEH-X7600S/XNUC...
Page 73
S 1741 (A,25,23) Spring Switch CSN1081 C 892 (A,50,92) CKSRYB104K16 S 1742 (A,66,30) Push Switch CSG1155 C 901 (A,15,79) (A,B,C,D) CKSSYB102K50 S 1743 (A,74,19) Push Switch CSG1155 C 902 (A,16,79) CKSRYB105K16 C 903 (A,22,74) CEVQW221M6R3 CN1601 (B,109,9) Connector CKS6451 DEH-X7600S/XNUC...
Page 74
R 1725 (B,80,10) RAB4CQ102J R 245 (A,34,46) RS1/16SS104J R 1731 (A,72,10) RS1/16SS470J R 254 (A,37,56) RS1/16SS104J R 1753 (B,123,23) RAB4CQ473J R 260 (B,30,27) RS1/16SS103J R 1755 (A,116,28) RAB4CQ101J R 264 (A,22,9) RS1/16SS102J R 1756 (B,124,25) RS1/16SS154J R 281 (B,33,38) RS1/16SS560J DEH-X7600S/XNUC...
Page 75
C 238 (A,25,44) CKSRYB104K16 C 299 (A,26,41) CKSSYB104K10 C 302 (B,28,12) CKSSYB102K50 C 303 (B,29,12) CKSSYB102K50 C 304 (B,27,12) CKSSYB223K16 C 305 (B,26,12) CKSSYB104K10 C 306 (A,31,7) CKSSYB104K10 C 307 (A,41,19) CKSRYB105K10 C 308 (A,31,15) CKSRYB105K10 C 710 (A,34,42) CKSSYB102K50 DEH-X7600S/XNUC...