Related Manuals for AudioCodes M500Li
Summary of Contents for AudioCodes M500Li
- Page 1 Configuration Guide AudioCodes Mediant™ Multi-Service Business Routers Series Voice Gateway Basic Configuration M500Li Analog VoIP Gateway Version 7.2...
-
Page 3: Table Of Contents
Table of Contents Notice ..........................ii WEEE EU Directive .......................... ii Customer Support .......................... ii Stay in the Loop with AudioCodes ....................ii Abbreviations and Terminology ...................... ii Related Documentation ........................ii Important Notes ..........................ii Document Revision Record ......................iii Documentation Feedback ...................... -
Page 4: Notice
Customer Support Customer technical support and services are provided by AudioCodes or by an authorized AudioCodes Service Partner. For more information on how to buy technical support for AudioCodes products and for contact information, please visit our website at https://www.audiocodes.com/services-support/maintenance-and-support. -
Page 5: Document Revision Record
31636 Voice configuration updated. Documentation Feedback AudioCodes continually strives to produce high quality documentation. If you have any comments (suggestions or errors) regarding this document, please fill out the Documentation Feedback form on our website at https://online.audiocodes.com/documentation-feedback. - iii -... -
Page 6: Getting Started With Initial Connectivity
1. Getting Started with Initial Connectivity M500Li Analog VoIP Gateway Getting Started with Initial Connectivity Introduction This part describes how to initially access the device's management interface and change its default IP address to correspond with your networking scheme. Device management can always be done through the LAN interface. It can also be enabled for the WAN interface as explained in section 1.3.2,... -
Page 7: Accessing The Device Using The Default Lan Ip Address
1. Getting Started with Initial Connectivity M500Li Analog VoIP Gateway 1.2.2 Accessing the Device Using the Default LAN IP Address To access the device using the default LAN IP address: Connect the LAN Port directly to your computer's network interface using a straight- through Ethernet cable: Make sure that your computer is configured to automatically obtain an IP address. -
Page 8: Configuring Voice Gateway Lan And Wan
1. Getting Started with Initial Connectivity M500Li Analog VoIP Gateway Configuring Voice Gateway LAN and WAN This section describes how to configure the device's LAN and WAN interfaces. After accessing the device through the LAN interface, you can configure Web management... -
Page 9: Configuring The Wan Interface
1. Getting Started with Initial Connectivity M500Li Analog VoIP Gateway 1.3.2 Configuring the WAN Interface This procedure describes how to configure the WAN interface and uses Gigabit Ethernet. Before configuring the WAN interface, make sure that you have all the required... -
Page 10: Voice Gateway Using Proxy Server
2. Voice Gateway using Proxy Server M500Li Analog VoIP Gateway Voice Gateway using Proxy Server This example scenario describes how to route calls when the Voice Gateway configured to work using a Proxy Server and FXS ports (Basic configuration). Figure 2-1: Example of Voice Gateway using SIP Proxy and FXS Ports WAN Interface Configuration This section describes the WAN Interface configuration of the Voice Gateway. -
Page 11: Voice Configuration
2. Voice Gateway using Proxy Server M500Li Analog VoIP Gateway Voice Configuration This section describes the voice configuration on Voice Gateway. 2.2.1 Configuring Proxy Server Address To configure Proxy Server Address (IP or Hostname): Open the Proxy Sets page (Setup menu > SIGNALING & MEDIA tab > CORE ENTITIES folder >... -
Page 12: Configuring Fxs Ports (Trunk Groups)
2. Voice Gateway using Proxy Server M500Li Analog VoIP Gateway 2.2.2 Configuring FXS Ports (Trunk Groups) To configure FXS Ports (Trunk Groups): Open the Trunk Groups page (Setup menu > SIGNALING & MEDIA tab > GATEWAY folder > ◼ Trunks & Groups folder > Trunk Groups). -
Page 13: Configuring Fxs Authentication
2. Voice Gateway using Proxy Server M500Li Analog VoIP Gateway 2.2.4 Configuring FXS Authentication To configure FXS Authentication: Open the Authentication page (Setup menu > SIGNALING & MEDIA tab > GATEWAY folder > ◼ Analog Gateway folder > Authentication). 2.2.5 Configuring IP ->... -
Page 14: Configuring Proxy & Registration
2. Voice Gateway using Proxy Server M500Li Analog VoIP Gateway 2.2.6 Configuring Proxy & Registration To configure Proxy & Registration: Open the Proxy & Registration page (Setup menu > SIGNALING & MEDIA tab > SIP DEFINTIONS folder > Proxy & Registration). - Page 15 Website: https://www.audiocodes.com ©2022 AudioCodes Ltd. All rights reserved. AudioCodes, AC, HD VoIP, HD VoIP Sounds Better, IPmedia, Mediant, MediaPack, What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your Gateway To VoIP, 3GX, VocaNom, AudioCodes One Voice, AudioCodes Meeting Insights, AudioCodes Room Experience and CloudBond are trademarks or registered trademarks of AudioCodes Limited.