Philips FW-C28 Manual page 13

All manuals and user guides at all-guides.com
™ The CD carousel tray will rotate until
the inner tray is rotated out and is
ready for changing.
3 Press OPEN•CLOSE to close the CD
carousel tray.
Selecting a desired track
Selecting a desired track when
playback is stopped
1 Press í or ë until the desired track
appears on the display.
2 PressÉ to start playback.
™ The selected track number and
elapsed playing time appear on the
display.
Selecting a desired track during
playback
• Press í or ë until the desired track
appears on the display.
™ The selected track number and
elapsed playing time appear on the
display.
• If you press í once it will skip to the
beginning of the current track and play
the track again.
Note:
– Pressing í during shuffling can only
skip to the beginning of the current
track.
pg 01-24/C28/22-Eng 13
Notes:
Searching for a particular
– If the total playing time is more than
passage during playback
" 99 : 59 " or if one of the programmed
• Press and hold à or á until the
tracks has a number greater than 30,
desired passage is located. then " -- : -- " appears on the display
™ The volume will be reduced.
instead of the total playing time.
• Play returns to normal when à or á
– If the system is reading the discs,
is released.
programming is not possible,
" READING " will be displayed and
followed by " DISC X ". " X " is the
Programming Tracks
current read disc number.
Programming tracks of a loaded CD is
– During programming, if no button is
possible when playback is stopped. The
pressed within 20 seconds, the system
display will indicate the total tracks stored
will exit program mode automatically.
in the program. Up to 40 tracks can be
stored in the memory in any order. When
Reviewing the program
40 tracks are stored and you attempt to
store another track, the display will show
Reviewing of the program is possible only
"PROGRAM FULL".
when playback is stopped.
• Pressí or ë repeatedly to review the
1 Load the desired discs in the disc trays.
programmed tracks.
2 Press PROGRAM to start programming.
• Press Ç to exit review mode.
™ The PROG flag starts flashing.
™ It will cancel any previously selected
repeat mode. Playing the program
3 Press the CD (CD 1•2•3) or DISC 1/2/3
1 Press É to start program playback.
button to select the disc.
™ "PLAY PROGRAM" will be
4 Pressí or ë to select the desired
track.
™ The track number and elapsed
5 Press PROGRAM to store the track.
• Repeat steps 3 to 5 to store other discs
and tracks.
• If you press REPEAT during program
6 Press Ç once to end programming.
playback, the current track or all
™ The total number of tracks
programmed tracks will be played
programmed and total playing time
repeatedly.
appear on the display.
™ "TRACK" or "PROGRAM" will be
displayed.
™ The REP and PROG flags appear on
the display.
2 Press Ç to stop program playback.
Notes:
– If you press any of the CD DIRECT PLAY
buttons, the system will play the
selected disc or track and the stored
program will be ignored temporarily. The
PROG display also will disappear
temporarily from the display. It will
reappear when playback of the selected
disc ends.
– REPEAT DISC mode will be cancelled
when program playback begins.
Erasing the program
playback is stopped)
• Press Ç.
™ "PROGRAM CLEARED" will be
displayed.
Note:
– The program will be erased when the
system is disconnected from the power
displayed.
supply or when the CD carousel tray is
opened.
playing time of the current track will
appear on the display.
3/7/00, 5:14 PM
CD
(when
13
3139 116 19331 3139 116 19331