Command Data - Dukane 28A8035 Operating Manual

Connection to the control signal terminal (continued)
Item
MOUSE
COMMUNICATE
POWER
MIRROR
INPUT
VIDEO SYSTEM
VOLUME
MUTE
BRIGHT
CONTRAST
COLOR
TINT
SHARPNESS
H. PHASE
H. POSIT
H. SIZE
V. POSIT
COLOR BALANCE 00h 00h 00h (for Red) ~ 00h 00h 24h (for Blue)
AUTO ADJUST
BLANK
REVEAL
MAGNIFY
FREEZE
Caution If computer sends the undefined command code or data code, Projector can not guarantee operation.
Command is consisted of 2 command bytes and following data bytes.
1-st byte indicates the kinds of commands and the length of command.
'0xH' : Error-reply
'1xH' : Command reply
'2xH' : Ask command
'3xH' : Set command
'4xH' : Default set command
'5xH' - 'FxH' : Reserved
'x' indicates the length of data bytes.
2-nd byte indicates the command code 'yy' as command table.
Data table shows the data byte.
26

Command data

00h=stop mouse emulation. 01~7Fh=start mouse emulation
0Xh=8N1, 1Xh=7N1
X0h=1200bps, X1h=2400bps, X2h=4800bps, X3h=9600bps, X4h=19200bps
3Eh=Power off (Standby mode), 3Fh=Power on
00h=Normal, 01h=H:Invert, 02h=V:Invert, 03h=H&V:Invert
11h=VIDEO, 21h=RGB1, 22h=RGB2
00h 00h=Auto, 00h 01h=NTSC, 00h 04h=NTSC4.43
00h 02h=PAL, 00h 03h=SECAM, 00h 05h=M-PAL, 00h 06h=N-PAL
00h (min) ~ 24h (max)
00h=Mute off, 01h=Mute on
00h 00h 00h (dark) ~ 00h 00h 24h (brite)
00h 00h 00h (lower) ~ 00h 00h 24h (higher)
00h 00h 00h (less) ~ 00h 00h 24h (more)
00h 00h 00h (red) ~ 00h 00h 24h (green)
00h 00h 00h (soft) ~ 00h 00h 24h (sharp)
00h 00h 00h ~ 00h 00h 1Fh
00h 00h 4Fh 00h (left) ~ 00h 00h 17h 05h (right)
00h 00h 06h 06h (narrow) ~ 00h 00h 04h 0Ch (wide)
00h 00h 03h 00h (down) ~ 00h 00h 00h 06h (up)
00h (start) , 07h (stop)
0Xh=Blank off, 1Xh=Blank on
bit0 0=Blue off, 1=Blue on, bit1 0=Green off, 1=Green on
bit2 0=Red off, 1=Red on, bit3 0=Not change, 1=change
X1h=Reveal down, X4h=Reveal right, X=0 (slow) ~ 7 (fast)
(1) Circuit codes when ask code and default set code are issued (Number of data byte=1)
(2) When magnification is set by setting codes (Number of data bytes=6)
1st, 2nd data bytes: magnification starting positions in horizontal direction (left end)
3rd, 4th data bytes: magnification starting positions in vertical direction (top)
5th, 6th data bytes: Horizontally magnified dot number data
00h=normal display, 01h=still picture display
Projector sends to computer.
Projector sends to computer.
Computer sends to Projector.
Computer sends to Projector.
Computer sends to Projector
Data code
00h=normal display, 01h=magnified display
00h 00h (left) ~ 3Ch 05h (right)
00h 00h (top) ~ 0Dh 04h (bottom)
64h 00h (large) ~ 20h 06h (small)