Self-Diagnosis Function - Sony DSC-RX10 Service Manual

1-5. SELF-DIAGNOSIS FUNCTION

1-5-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
LCD screen
Blinks at 3.2 Hz
C 3 2 0 0
Repaired by: Block
C : Corrected by customer Refer to "1-5-3. Self-diagnosis Code Tabl e".
Indicates the appropriate
E : Corrected by service step to be taken.
engineer E.g.
13 ....Format the "memory card".
32 ....Turn on power again.
DSC-RX10_L2
1-5-2. Self-diagnosis Display
When problems occur while the unit is operating, the LCD screen shows
a 4-digit display consisting of an alphabet and numbers, which blinks
at 3.2 Hz. This 5-character display indicates the "repaired by:", "block"
in which the problem occurred, and "detailed code" of the problem.
Detailed Code
1-5-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Block Detailed
Function Code
Memory card is unformatted.
Memory card is broken.
C 1 3 0 1
Memory card type error
The camera cannot read or write data on the
memory card.
C 3 2 0 1 Trouble with hardware
Abnormality of wireless LAN module or
E 4 1 0 0
host CPU.
Difficult to adjust focus
E 6 1 0 0
(Cannot initialize focus)
Zoom operations fault
E 6 1 1 0
(Cannot initialize zoom lens.)
Reset position detection error on the stepper
E 6 1 3 0
iris initializing
E 6 2 0 2 Abnormality of IC for steadyshot.
E 6 2 1 0 Lens initializing failure.
E 6 2 1 1 Lens overheating (PITCH).
E 6 2 1 2 Lens overheating (YAW).
E 6 2 2 0 Abnormality of thermistor.
E 9 1 0 1 Abnormality when flash is being charged.
E 9 2 0 0 Battery / Dry cell distinction defect
E 9 4 0 0 Internal memory fault
*
E 9 5 0 0 GPS hardware error
*
E 9 5 0 1 Acceleration sensor hardware error
Electronic compass hardware error
E 9 5 0 2
*
(GPS hardware error)
Note 1: After repair, be sure to perform "1-6. PROCESS AFTER FIXING FLASH ERROR".
Note 2: Functions of codes with * mark are not provided in this unit.
1-3
– ENGLISH –
Correction
Format the memory card.
Insert a new memory card.
Insert a supported memory card.
Turn the power off and on again, or taking out and inserting the
memory card several times.
Turn the power off and on again.
Replace the SY-1027 board.
Retry turn the power on by the power switch. If it does not recover,
check the focus MR sensor signal of lens block (pin 2, 4 of CN3101
on the SY-1027 board). If it is OK, check the focus motor drive IC
(IC3104 on the SY-1027 board).
Retry turn the power on by the power switch. Check the zoom reset
sensor signal of lens block (pin ej of CN3101 on the SY-1027 board)
when zooming is performed when the zoom button is operated. If it is
OK, check the zoom motor drive IC (IC3104 on the SY-1027 board).
Turn power off and turn power on again.
Check or replacement of the IC for steadyshot (IC3104 on the SY-
1027 board).
Check or replacement of the IC for steadyshot (IC3104 on the SY-
1027 board).
Check the HALL element (PITCH) of optical image stabilizer (pin
5, 7 of CN3101 on the SY-1027 board). If it is OK, check PITCH
angular velocity sensor (SE3100 on the SY-1027 board) peripheral
circuits.
Check the HALL element (YAW) of optical image stabilizer (pin 9,
qa of CN3101 on the SY-1027 board). If it is OK, check YAW angular
velocity sensor (SE3100 on the SY-1027 board) peripheral circuits.
Check the temp sensor of optical image stabilizer (pin eg of CN3101
on the SY-1027 board).
Checking of flash unit or replacement of flash unit. (Note 1)
Turn power off and turn power on again.
Turn power off and turn power on again.
Turn power off and turn power on again.
Turn power off and turn power on again.
Turn power off and turn power on again.