Service / Warranty - Capital Precision Series Use And Installation Manual

STEP 4: INSTALLING ANTI-TIP DEVICE
For all Ranges, an anti-tip device MUST be installed
as per these instructions.
WARNING!
• ALL RANGES CAN TIP
• INJURY TO PERSONS COULD RESULT
• INSTALL ANTI-TIP DEVICES PACKED WITH RANGE
• SEE INSTALLATION INSTRUCTION
WARNING: RANGE TIPPING HAZARD!
• All ranges can tip and injury can result. To prevent
accidental tipping of the range, attach it to the
floor, wall or cabinet by installing the Anti-Tip
Device supplied.
• A risk of tip-over may exist if the appliance is not
installed in accordance with these instructions.
• If the range is pulled away from the wall for
cleaning, service or any other reason, ensure that
the Anti-Tip Device is properly re-engaged when
the range is pushed back against the wall. In
the event of abnormal usage (such as a person
standing, sitting, or leaning on an open door),
failure to take this precaution can result in tipping
of the range. Personal injury might result from
spilled hot liquids or from the range itself.
WARNING: ELECTRICAL SHOCK HAZARD!
• Use extreme caution when drilling holes into the
wall or floor. There may be concealed electrical
wires located behind the wall or under the floor.
• Identify the electrical circuits that could be affected
by the installation of the Anti-Tip Device, then turn
off power to these circuits.
• Failure to follow these instructions may result in
electrical shock or other personal injury.
CAUTION: PROPERTY DAMAGE!
• Contact a qualified installer or contractor to
determine the proper method for drilling holes
through the wall or floor material (such as ceramic
tile, hardwood, marble, etc.)
• DO NOT slide range across unprotected floor.
• Failure to follow these instructions may result in
damage to wall or floor coverings.
TOOLS NEEDED FOR INSTALLATION OF
ANTI-TIP DEVICE!
1. Screwdriver, Phillips
2. Drill, electric or hand
3. Measuring tape or ruler
4. 1/8" drill bit (wood or metal wall or floor)
5. 3/16" anchors, drywall, or concrete, 2 each (not
required if mounting bracket is being attached to
solid wood or metal.
6. Hammer
7. Pencil or other marker
IMPORTANT INSTALLATION INFORMATION
• The Anti-Tip Bracket may be attached to a solid
wood cabinet having a minimum wall thickness of 3/4".
ANTI-TIP BRACKET
MODEL A
30" 14-15/16"
36" 17-15/16"
48" 23-15/16"
60" 24-15/16"
THIS SIDE
AGAINST WALL
I N S T A L L A T I O N I N S T R U C T I O N S
• The thickness of the wall or floor may require use of
longer screws, available at your local hardware store.
• In all cases at least one (1) of the bracket mounting
screws must be fastened to solid wood or metal
on each side.
• Use appropriate anchors when fastening the
mounting bracket to any material other than
hardwood or metal.
MOUNTING ANTI-TIP BRACKET:
The alternative floor mounted bracket shall be
installed as follows:
• Place bracket on floor in position shown in Figure below.
• Secure to floor or wall stud.
• Later, when unit is installed, the adjustable leg will
slide under the bracket
STEP 5: GAS CONNECTION AND HOOK-UP
Verify the type of gas being used at the installation
site matches the gas type of the range. As shipped
from the factory, units are configured for use with
Natural Gas or Propane (LP). Make certain the range
matches the type of gas available at this location.
For installation of the appliance at high altitude,
please consult your local gas company for their
recommendation of the correct orifice sizes and any
other necessary adjustments that will provide proper
gas combustion at specified altitudes.
NOTE: Capital DOES NOT supply ranges to match
varying altitudes. Orifices to adjust for combustion
for differing altitudes may be purchased through
Capital Cooking Equipment by calling our Parts
Department at 1-866-402-4600, or email us at
customerservice@capital-cooking.com.