Table of Contents
Advertisement
26
Speaker and Delay/Distance Setup
SPEAKER DISTANCE SETUP
FRONT LEFT
CENTER
FRONT RIGHT
SURROUND RIGHT
CENTER BACK RIGHT
OVERHEAD FRONT RIGHT
OVERHEAD REAR RIGHT
OVERHEAD REAR LEFT
OVERHEAD FRONT LEFT
CENTER BACK LEFT
SURROUND LEFT
SUBWOOFER
BACK
The SPEAKER DISTANCE SETUP menu, which is reached from the MAIN
menu, allows you to set the delay for individual speakers. This ensures that
the sound from each speaker arrives simultaneously at the listening position,
even when the speakers are not all placed at equal distances from the
listener. Increase the delay to speakers located closer to the seating area
and decrease the delay to speakers located farther from the seating area.
The Audio Configuration will determine which speakers are displayed in
the Speaker Distance Setup menu.
This Rotel processor makes setting the delay time for each speaker very
easy. Simply measure the distance (in feet or meters) from your seating
position to each speaker in your system. Set the measured distance in the
line for each speaker. The menu provides a line for each speaker configured
in your system and gives a range of settings up to 33 feet (10.06 meters)
in 0.25 foot (0.075 m) increments with each increment equivalent to an
additional delay of 0.25 ms.
To change a setting, place the highlight on the desired line using the Up/
Down arrow buttons and use the Left/Right arrow buttons to increase or
decrease the delay. To return to the MAIN menu, press the BACK button or
select "BACK" on the OSD. Press the SETUP button or select "EXIT" on the
OSD to exit setup and return to normal operation.
Miscellaneous Settings
System Setup
SYSTEM SETUP
LANGUAGE
IR REMOTE CODESET
DISPLAY
NETWORK WAKEUP
POWER OPTION
NETWORK CONFIGURATION
SOFTWARE INFORMATION
RESTORE FACTORY DEFAULT
BACK
This SYSTEM SETUP menu, reached from the MAIN menu, provides access
to several miscellaneous settings as follows:
LANGUAGE: Selects a language for the On Screen Display.
IR REMOTE CODESET: The RSP-1576MKII has two IR codesets and can be
changed in the event there is a conflict of IR codes with other Rotel products.
NOTE: After changing the IR REMOTE CODESET the remote must
also be changed to continue using the remote control. Push and hold
the TUNER button and 1 (or TUNER and 2 for codeset 2) at the same
10.00 FT
3.05M
10.00 FT
3.05M
10.00 FT
3.05M
10.00 FT
3.05M
10.00 FT
3.05M
10.00 FT
3.05M
10.00 FT
3.05M
10.00 FT
3.05M
10.00 FT
3.05M
10.00 FT
3.05M
10.00 FT
3.05M
10.00 FT
3.05M
ENGLISH
CODESET 1
HDMI AND VFD
DISABLE
RSP-1576MKII Surround Sound Processor
time and hold for approximately 5 seconds until the backlights on the
remote control blink on then off then release both buttons. This sets the
remote control to use codeset 1 (or codeset 2 if TUNER and 2 are held).
DISPLAY: Sets the information shown on the main HDMI OSD and front VFD
display. Settings are "Off", "HDMI ONLY", "VFD ONLY" or "HDMI AND VFD".
NETWORK WAKEUP: Enable or Disable power on and power off via the
network connection. Enable this function for use with automation systems
using IP control.
NOTE: The Network Wakeup function is not available in all regions.
NOTE: When Network Wakeup is configured to enabled, the RSP-
1576MKII will consume additional power in standby mode.
POWER OPTION: Access to configuration of Off Timer, Max Power On
Volume, Power Mode and Signal Sense Input.
POWER OPTION
OFF TIMER
MAX POWER ON VOLUME
POWER MODE
SIGNAL SENSE INPUT
BACK
OFF TIMER: Set the amount of time the units stays powered on when
there is no audio signal. The RSP-1576MKII will automatically go to
standby mode if audio is not detected for the specified timer period.
Default: 20 MINS.
Valid settings include: Disable, 20 MINS, 1 HOUR, 2 HOURS, 4 HOURS.
MAX POWER ON VOLUME: Specifies the maximum volume level to be
used each time the unit powered on. Valid settings include: 20 - 70.
Default: 45.
POWER MODE: Enables the rear panel USB power port and the Network
connection to remain powered at all times. The power consumption is
higher in Quick Power mode. To enable continuous power to the rear USB
power port and allow for IP control of Power-On select the Quick option.
Valid settings include: NORMAL, QUICK.
NOTE: When the POWER MODE is configured to Quick, the RSP-
1576MKII will consume additional power in standby mode.
NOTE: Some regions limit the amount of Standby Power Consumption
allowed and the POWER MODE will not be available. To control the
Rotel product in this case use the RS232 connection. For questions
on the availablity of the Power Mode please contact your authorized
Rotel dealer.
SIGNAL SENSE INPUT: Checks if a digital audio signal is present on the
configured Signal Sense Input. When this input is selected as the active
listening source, the RSP-1576MKII monitors the digital data stream to
determine if there is audio. If there is no audio detected for 10 minutes,
20 MINS
45
NORMAL
DISABLE
Advertisement
Table of Contents
