Related Manuals for MASSEY FERGUSON MF1746
Summary of Contents for MASSEY FERGUSON MF1746
- Page 1 Service Manual 1746 / 1756 Round Baler VISION INNOVATION LEADERSHIP QUALITY RELIABILITY SUPPORT PRIDE COMMITMENT...
- Page 2 Find manuals at https://best-manuals.com...
- Page 3 ® Massey Ferguson 1746 / 1756 Round Baler SERVICE MANUAL 4283381M2 CONTENTS GENERAL INFORMATION ..............................01 DRIVES....................................02 PICKUP....................................03 ELECTRICAL ..................................04 BALE FORMING ................................. 05 BALE WRAPPING................................06 MAINFRAME AND WHEELS ............................. 07 HYDRAULICS ..................................08 INDEX ....................................09...
- Page 4 NOTES 01-ii 4283381M2 Find manuals at https://best-manuals.com...
-
Page 5: Table Of Contents
Contents ® Massey Ferguson 1746 / 1756 Round Baler SERVICE MANUAL 4283381M2 01 - General Information Contents Introduction ..............................01-3 Units of Measurement ..........................01-3 Replacement Parts ..........................01-3 Serial Number Plate Location ........................01-3 Machine Identification ..........................01-3 Baler Operation ............................01-4 Tailgate Lockout Valve .......................... - Page 6 Contents NOTES 01-2 4283381M2 Find manuals at https://best-manuals.com...
-
Page 7: Introduction
General Information GENERAL INFORMATION INTRODUCTION The operation and maintenance instructions included in this manual are assembled from field testing and other data. The information is written for general conditions. Make adjustments as necessary for specific conditions. Right-hand and left-hand, as used in this manual, is determined by facing the direction the machine will travel when in use. -
Page 8: Baler Operation
General Information Dealer's Fax No.: ______________________________ Baler Operation d-11251 FIG. 2 FIG. 2: The illustration shows the windrowed crop being picked up. The crop moves across the pickup assembly (1) into the bottom of the open throat bale chamber. The windguard (2) holds the crop against the pickup assembly. -
Page 9: Tailgate Lockout Valve
General Information FIG. 3: The illustration shows the full size bale. The bale density rolls (1) have moved upward, to increase the size of the bale chamber. The bale is on the tailgate carrier roll (2). The bale must now be wrapped and unloaded. d-11252 FIG. -
Page 10: Baler Components
General Information Baler Components N202340 FIG. 5 Right-hand side of the baler. Drive roll shaft Twine arm actuator Forming belts tensioning arm Windguard Forming belts tensioning cylinder Tailgate latch strap (10) Forming belts tensioning spring Tailgate hydraulic cylinder (11) Implement driveline Tailgate hinge pivot point (12) Slip clutch (Located under lid) Right-hand twine box... - Page 11 General Information Tailgate FIG. 5: The tailgate is the rear half section of the bale chamber and is supported by a hinge that is at the top. The tailgate is operated by two hydraulic cylinders to unload the bale. The tailgate has forming belt idler rolls and a bale carrier roll.
- Page 12 General Information Bale Density System FIG. 8: The bale density is controlled by two springs (1) and a hydraulic tension system. As the bale increases in size, oil is forced from the rod end of the forming belts tensioning cylinder (2) through a non-adjustable relief valve (3) to the base end.
- Page 13 General Information Lighting and Reflectors FIG. 10: The baler is equipped with a lighting and marking system. The lighting system includes the lighting wiring harness, seven pin SAE connector and the warning lamps (1). The marking system includes yellow front reflectors, red rear reflectors (2) and the SMV (slow moving vehicle) emblem (3) mounted on the back of the tailgate.
- Page 14 General Information Mesh Wrap System (Optional) FIG. 12: The baler is available with an optional mesh wrap system (1) in addition to the twine system. The mesh wrap assembly is mounted on the rear of the baler. The operator selects either twine or mesh wrap from the tractor using the console.
-
Page 15: Forming Belts Warranty
General Information Forming Belts Warranty Forming Belts Eligible for Warranty Replacement FIG. 14: Belts are warrantable if the material and/or workmanship is defective and the machine is under warranty. Ply separation is warrantable within the warranty period of the machine. STD-92001-01 FIG. - Page 16 General Information FIG. 17: Belts with holes and/or tears are not considered a warranted failure. 56RA-01B06 FIG. 17 FIG. 18: Belts with tears are not considered a warranted failure. Forming belts damaged by accumulation of crop and/or foreign objects are not eligible for warranty replacement. 56RA-01B10 FIG.
-
Page 17: Safety
General Information SAFETY Safety Alert Symbol FIG. 19: The safety alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! This safety alert symbol indicates important safety messages in this Operator Manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury or death. -
Page 18: Operator Manual
General Information Operator Manual The photos, illustrations, and data used in this manual were current at the time of printing, but due to possible in-line production changes, your machine can vary slightly in detail. The manufacturer reserves the right to redesign and change the machine as necessary without notification. -
Page 19: Operation
General Information Operation Make sure the machine is in the proper operating condition as stated in the Operator Manual. Make sure the tractor is in proper operating condition with the brakes adjusted, especially when operating on terrain that is not even. To achieve proper braking capacity, the weight of the baler with a bale must not exceed 1.5 times the weight of the tractor. - Page 20 General Information FIG. 25: Because of the flammable nature of many hay crops, a water fire extinguisher must be placed within easy reach. Keep a first aid kit handy for treatment for minor cuts and scratches. Keep fingers clear of the feed roll pinch point when threading the mesh wrap.
-
Page 21: Travel On Public Roads
General Information Travel On Public Roads FIG. 28: Use the lighting and marking system supplied with the machine when roading. Make sure reflectors are correctly installed, in good condition, and wiped clean. Be sure the SMV emblem is clean, visible, and correctly mounted on the rear of the machine. -
Page 22: Fire Prevention
General Information Fire Prevention FIG. 29: Due to the nature of the crops this machine will operate in, the risk of fire is of concern. Regular inspection of the machine can reduce the risk of fire. Keep the machine free of crop debris. Check the machine daily for any noises that are not normal. - Page 23 General Information FIG. 32: DO NOT operate the machine with drive shafts shields open or removed. Entanglement in rotating drive shafts can cause serious injury or death. Stay clear of rotating components. Make sure rotating guards turn freely. A loose yoke can slip off the tractor PTO shaft and result in injury to persons or damage to the machine.
-
Page 24: Tire Safety
General Information FIG. 36: Use a piece of cardboard or wood to search for possible leaks, never use your hands. Wear leather gloves for hand protection and safety goggles for eye protection. DO NOT use your bare hand. Relieve all pressure before disconnecting any hydraulic lines. -
Page 25: Specifications
General Information SPECIFICATIONS Specifications and design are subject to change without notice and without liability therefore. 4 X 6 Baler Dimensions and Weights Width (overall)............................2550 mm (100 in) Length (overall) ............................4115 mm (162 in) Height (overall)............................3000 mm (118 in) Weight (approximate) .......................... - Page 26 General Information Drives PTO speed............................. 540 or 1000 rev/min Pickup.................................. chain driven Forming belts ..............................chain driven Gearbox ..........................540 or 1000 rev/min, 90 degree Pickup Width on flare ............................. 1188 mm (46.75 in) tine to tine............................1122 mm (44.17 in) gathering wheel to gathering wheel (optional)..................
- Page 27 General Information Lubrication Grease fitting lubricant..................... No. 2 multipurpose lithium grease Roller chain lubricant ............................ clean engine oil Gearbox capacity ............................0.83 liter (1-3/4 pint) lubricant..............................SAE EP 90 W Wheel bearing lubricant....................heavy duty wheel bearing grease Forming belt tension system capacity ..............................
-
Page 28: 5 X 6 Baler
General Information 5 X 6 Baler Dimensions and Weights Width (overall)............................4115 mm (162 in) Length (overall) ............................3734 mm (147 in) Height (overall)............................3000 mm (118 in) Weight (approximate) ..........................2440 kg (5380 lb) Tongue weight (empty) ..........................569 kg (1250 lb) Bale Size Bale diameter minimum.............................. - Page 29 General Information Tires Size Standard......................... 31 x 13.50 - 15, 8 ply rib implement Optional..........................14L-16.1, 8 ply rib implement Wheel nut size ................................9/16-18 Wheel nut torque ............................. 165 Nm (120 lbf ft) Tire pressure..............................240 Kpa (35 psi) Drives PTO speed.............................
-
Page 30: Gearbox
General Information Tractor Requirements PTO speeds............................540 or 1000 rev/min Minimum recommended PTO power......................52.2 kW (70 hp) Minimum tractor weight ..........................3175 kg (7000 lb) Hydraulics ................................. single remote Electrical system................................. 12V dc Tractor tire spacing maximum rear............................. 2591 mm (102 in) minimum front and rear ........................ - Page 31 This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...