Related Manuals for Pfaff EcoDrive P40 ED
Summary of Contents for Pfaff EcoDrive P40 ED
- Page 1 EcoDrive P40 ED P70 ED INSTRUCTION MANUAL Part 2 Control panel BDF S2 296-12-18 627/002 Betriebsanleitung engl. 06.09...
- Page 2 The reprinting, copying or translation of PFAFF Instruction Manuals, whether in whole or in part, is only permitted with our previous authorization and with written reference to the source. PFAFF Industriesysteme und Maschinen AG Hans-Geiger-Str. 12 - IG Nord D-67661 Kaiserslautern...
-
Page 3: Table Of Contents
Contents Contents ................Chapter - Page Operating elements of the S2 control panel ..............1 Screen displays ......................... 1 Function keys ........................1 Entering the start and end backtacks ................4 Setting the stitch count function for controlling the amount of bobbin thread ....5 Bobbin thread control on the sub-class -926/06 (optional) .......... - Page 4 Contents Contents ................Chapter - Page .01.06 Test block 5 –light barrier ....................19 .01.07 Test block 6 – thread monitor (only on subclass -926/06) ..........19 .02.08 Test block 7 – data transfer ..................... 19 Reset / Cold start ......................20 Internet update of the machine software ................
-
Page 5: Operating Elements Of The S2 Control Panel
Controls Operating elements of the S2 control panel The control panel is used to create and alter seam programs, enter parameter values and read error messages and service settings. The control panel consists of display 1 and the function keys described below. Display 1 consists of a two-row, alpha-numerical display with 16 symbols per row. - Page 6 Controls Start backtacks If this key is pressed, the backtacks at the beginning of the seam (start backtacks) are switched on or off. The number of forward stitches (A) or reverse stitches (B) for the start backtacks can be changed by pressing the +/- key underneath. To convert from double backtack to single backtack set the number of stitches for the corresponding seam section at zero.
- Page 7 Controls Programmed stop (only in programmed sewing) If this key is pressed the corresponding function is switched on or off. When the function is switched on, in programmed sewing the machine stops automatically at the end of the seam section. Photocell In manual sewing the number of compensating stitches from the point where the photocell is light to the end of the seam can be set under parameter 111, and in...
-
Page 8: Entering The Start And End Backtacks
Controls Entering the start and end backtacks Switch on the machine. By pressing the corresponding +/- key ("A") select the desired value for the number of forward stitches (A) of the start backtack. By pressing the corresponding +/- key ("B") select the desired value for the number of reverse stitches (B) of the start backtack. -
Page 9: Setting The Stitch Count Function For Controlling The Amount Of Bobbin Thread
Controls Setting the stitch count function for controlling the amount of bobbin thread Switch on the machine. Press the TE/Speed key twice to call up the parameter input function. Select the parameter "760" by pressing the corresponding +/- key. Press the corresponding +/- key to set the number of remaining stitches, which can still be sewn after recognition by the bobbin thread control function. -
Page 10: Sewing
Sewing Sewing In the sewing mode, all relevant settings for the sewing operation are shown on the display and can be altered directly. Functions can be switched on or off by pressing a key. In this mode a difference is made between manual sewing and programmed sewing. To change from manual to programmed sewing, press the PM key. -
Page 11: Programmed Sewing
Sewing Programmed sewing In programmed sewing 99 programs, each with 9 seam segments and 999 stitches, can be programmed. The seam segments can be programmed by entering the number of stitches or by using the "Teach" function (sewing a seam segment). Fixed programs are used for the quick and convenient production of seams with a different number of stitches. -
Page 12: An Example Of Programmed Sewing
Sewing An example of programmed sewing Programming by entering the number of stitches .03.01 seam segment 1 seam segment 4 program 1 seam segment 2 seam segment 3 Example: Seam segment 1, 20 stitches, Functions: Start backtacks, programmed stop and raising foot at the end of the seam, Seam segment 2, 10 stitches, Functions: Programmed stop and raising foot at the end of the seam, Seam segment 3, 20 stitches,... - Page 13 Sewing 1000 With the corresponding +/- key, set the program with 4 seam segments. By entering the value "0" with the corresponding +/- key, stipulate that no program linking will take place. Press the scroll key twice. With the corresponding +/- key, select the seam segment "1". With the corresponding +/- key, enter the value "20"...
- Page 14 Sewing With the corresponding +/- key, select the seam segment " " " " " 3" " " " " . With the corresponding +/- key, enter the value "20" for the number of stitches. Press the programmed stop key to switch on the function. By pressing the raise foot after seam segment key, switch on the function.
-
Page 15: Programming With The "Teach Function
Sewing Programming with the "teach function" .03.02 seam segment 3 seam segment 1 program 2 seam segment 2 Example: Seam segment 1 Functions: Programmed stop and raising foot at the end of the seam, Seam segment 2 Functions: Programmed stop and raising foot at the end of the seam, Seam segment 3 Functions: Programmed stop, raising foot at the end of the seam and thread trimming Switch on the machine. - Page 16 Sewing TEACH With the corresponding +/- key, select the seam segment "1". Press the programmed stop key to switch on the function. By pressing the raise foot after seam segment key, switch on the function. Sew seam segment "1". TEACH The number of stitches is shown on the display.
- Page 17 Sewing TEACH With the corresponding +/- key, select the seam segment "3". Press the programmed stop key to switch on the function. By pressing the raise foot after seam segment key, switch on the function. Press the thread trimming key to switch on the function. The program end is recognized automatically through the thread trimming function.
-
Page 18: Error Messages
Sewing Error messages If a fault occurs, the text "ERROR" appears on the display, together with an error code and short instructions. An error message is caused by incorrect settings, faulty elements or seam programs as well as by overload conditions. The error code numbers are explained below. -
Page 19: Parameter Settings
Sewing Parameter settings Selecting the user level .06.01 (only in the "manual sewing" mode) Switch on the machine. Press the TE/Speed key twice to call up the parameter input function. Call up the parameter group "700" by pressing the corresponding +/- key. Call up parameter "798"... -
Page 20: Selecting And Altering Parameters (Only In The "Manual Sewing" Mode)
Sewing Selecting and altering parameters .06.02 (only in the "manual sewing" mode) Switch on the machine. Press the TE/Speed key twice to call up the parameter input function. By pressing the corresponding +/- key, select the parameter, e.g. "660" for bobbin thread monitoring. -
Page 21: Adjustment
Adjustment Adjustment Hardware-test The hardware test is a test program, which makes it possible, with the aid of the control panel, to check various components of the control system and the machine installation. The test consists of seven test blocks. Carrying out the hardware test 01.01 Switch on the machine. -
Page 22: Test Block 1 - Inputs
Adjustment Test block 2 – outputs 01.03 Output Output status Connector The output can be switched on Output number for 200 ms by pressing key D+ Contact number The functions allocated to the inputs displayed can be found in Part 3 Parameter list and connection plan. -
Page 23: Test Block 5 -Light Barrier
Adjustment Test block 5 –light barrier 01.06 0 = off Light barrier 1 = on The status of the light barrier can be checked here. Test block 6 – thread monitor 01.07 (only on subclass -926/06) Analogue value of the Thread thread monitor. -
Page 24: Reset / Cold Start
Adjustment Reset / Cold start After selecting the reset menu, by pressing the corresponding key it is possible to delete seam parameters, delete seam programs and to carry out a cold start. Press and hold "+" on keys A and D and switch on the machine. RESET Y - N Resetting the seam parameters... -
Page 25: Internet Update Of The Machine Software
Adjustment Internet update of the machine software The machine software can be updated with PFAFF flash programming. For this purpose the PFP boot program and the appropriate control software for the machine type must be installed on a PC. To transfer the data to the machine, the PC and the machine control unit must be connected with an appropriate null modem cable (part no. - Page 28 PFAFF Industriesysteme und Maschinen AG Hans-Geiger-Str. 12 - IG Nord D-67661 Kaiserslautern Phone: +49 - 631 200-0 Fax: +49 - 631 17202 E-mail: info@pfaff-industrial.com Hotlines: Technical service: +49 - 175/2243-101 Application consultance: +49 - 175/2243-102 Spare-parts hotline: +49 - 175/2243-103...