Denon RCD-M39 Service Manual page 88

PCM9211
SBAS495 – JUNE 2010
PIN
NO. NAME I/O
16 MPO1 O
17 DOUT O
18 LRCK O
19 BCK O
20 SCKO O
21 DGND –
22 DVDD –
23 MDO/ADR0 I/O
24 MDI/SDA I/O
25 MC/SCL I
26 MS/ADR1 I
27 MODE I
28 RXIN7/ADIN0 I
29 RXIN6/ALRCKI0 I
30 RXIN5/ABCKI0 I
31 RXIN4/ASCKI0 I
32 RXIN3 I
33 RXIN2 I
34 RST I
35 RXIN1 I
36 VDDRX –
37 RXIN0 I
38 GNDRX -
39 XTI I
40 XTO O
41 AGND –
42 VCC –
43 FILT O
44 VCOM O
45 AGNDAD –
46 VCCAD –
47 VINL I
48 VINR I
(2) Schmitt trigger input
2
(3) Open-drain configuration in I C mode
(4) Onboard pull-down resistor (50 kΩ, typical)
(5) CMOS Schmitt trigger input
8 Submit Documentation Feedback
All manuals and user guides at all-guides.com
PIN FUNCTIONS (continued)
5-V
TOLERANT
No Multipurpose output 1
No Main output port, serial digital audio data output
No Main output port, LR clock output
No Main output port, Bit clock output
No Main output port, System clock output
– Ground, for digital
– Power supply, 3.3 V (typ.), for digital
Yes Software control I/F, SPI data output / I
Yes Software control I/F, SPI data input / I
Yes Software control I/F, SPI clock input / I
Yes Software control I/F, SPI chip select / I
No Control mode setting, (see the
Yes Biphase signal, input 7 / AUXIN0, serial audio data input
Yes Biphase signal, input 6 / AUXIN0, LR clock input
Yes Biphase signal, input 5 / AUXIN0, bit clock input
Yes Biphase signal, input 4 / AUXIN0, system clock input
Yes Biphase signal, input 3
Yes Biphase signal, input 2
Yes Reset Input, active low
Yes Biphase signal, input 1, built-in coaxial amplifier
– Power supply, 3.3 V (typ.), for RXIN0 and RXIN1.
Yes Biphase signal, input 0, built-in coaxial amplifier
- Ground, for RXIN
No Oscillation circuit input for crystal resonator or external XTI clock source input
No Oscillation circuit output for crystal resonator
– Ground, for PLL analog
– Power supply, 3.3 V (typ.), for PLL analog
No External PLL loop filter connection terminal; must connect recommended filter
No ADC common voltage output; must connect external decoupling capacitor
– Ground, for ADC analog
– Power supply, 5.0 V (typ.), for ADC analog
No ADC analog voltage input, left channel
No ADC analog voltage input, right channel
Product Folder Link(s):
88
DESCRIPTION
2
C slave address setting0
2 (2) (3)
C data input/output
2 (2)
C clock input
2
C slave address setting1
Serial Control Mode section, Control Mode Pin Setting)
(2)
(2)
(2)
(2)
(2)
(2)
(2) (4)
Copyright © 2010, Texas Instruments Incorporated
PCM9211
www.ti.com
(2)
(2)
(5)