Sanyo EM-CD2900UK Service Manual
Sanyo EM-CD2900UK Service Manual

Sanyo EM-CD2900UK Service Manual

Commercial use combination oven

Advertisement

Quick Links

SERVICE
SERVICE          MANUAL
SERVICE
MANUAL
MANUAL
MANUAL
SERVICE
SERVICE
MANUAL
COMMERCIAL
COMMERCIAL          USE
COMMERCIAL
USE
USE          COMBINATION
USE
COMMERCIAL
COMMERCIAL
USE
MICROWAVE
MICROWAVE
MICROWAVE           OVEN
OVEN
OVEN
OVEN
MICROWAVE
MICROWAVE
OVEN
R e a d
R e a d
R e a d
R e a d
R e a d           t h i s
t h i s           m a n u a l
t h i s
t h i s
t h i s
m a n u a l
m a n u a l          c a r e f u l l y , e s p e c i a l l y
m a n u a l
m a n u a l
s t r i c t l y , c a r e l e s s
s t r i c t l y , c a r e l e s s
s t r i c t l y , c a r e l e s s           s e r v i c i n g
s t r i c t l y , c a r e l e s s
s t r i c t l y , c a r e l e s s
P R E C A U T I O N S
P R E C A U T I O N S
P R E C A U T I O N S
P R E C A U T I O N S           T O
P R E C A U T I O N S
E X P O S U R E
E X P O S U R E
E X P O S U R E           T O
E X P O S U R E
E X P O S U R E
T O
T O
T O           E X C E S S I V E
T O
(a)  Do not operate or allow the oven to be operated with the door open.
(b)  Make the following safety checks on all ovens to be serviced before activating the magnetron or other
     microwave source,and make repairs as necessary:
     (1)Interlock operation,(2)proper door closing,(3)seal and sealing surfaces(arcing,wear,and other
     damage),(4)damage to or loosening of hinges and latches,(5)evidence of dropping or abuse.
(c)  Before turning on microwave power for any service test or inspection within the microwave generating
     compartments,check the magnetron,wave guide or transmission line,and cavity for proper alignment,
     integrity,and connections.
(d)  Any defective or misadjusted components in the interlock,monitor,door seal,and microwave generation
     generation and transmission systems shall be repaired replaced,or adjusted by procedures describe
     in this manual before the oven is released to the owner.
               RoHS
RoHS
RoHS
RoHS
RoHS
This product does not contain any hazardous substances prohibited by the RoHS Directive.
(You will find R or Z at the last digit of serial number or a RSF label near the rating plate on
 the RoHS complaint product.)
     
     
      WARNING
WARNING
WARNING
WARNING
     
     
WARNING
You are requested to use RoHS compliant parts for maintenance or repair.
You are requested to use lead‑free solder.
COMBINATION
COMBINATION
COMBINATION
COMBINATION
Foreword
Foreword
Foreword
Foreword
Foreword
c a r e f u l l y , e s p e c i a l l y           p r e c a u t i o n
c a r e f u l l y , e s p e c i a l l y
c a r e f u l l y , e s p e c i a l l y
c a r e f u l l y , e s p e c i a l l y
s e r v i c i n g           a n d
s e r v i c i n g
s e r v i c i n g
a n d
a n d           t e s t i n g
a n d
t e s t i n g
t e s t i n g
t e s t i n g           m a y
s e r v i c i n g
a n d
t e s t i n g
T O
T O
T O
T O           B E
B E           O B S E R V E D
B E
B E
B E
O B S E R V E D           B E F O R E
O B S E R V E D
O B S E R V E D
O B S E R V E D
B E F O R E
B E F O R E
B E F O R E           A N D
B E F O R E
E X C E S S I V E
E X C E S S I V E           M I C R O W A V E
E X C E S S I V E
E X C E S S I V E
M I C R O W A V E
M I C R O W A V E
M I C R O W A V E
M I C R O W A V E           E N E R G Y
p r e c a u t i o n           o n   m i c r o w a v e   e n e r g y , a n d
p r e c a u t i o n
p r e c a u t i o n
p r e c a u t i o n
o n   m i c r o w a v e   e n e r g y , a n d
o n   m i c r o w a v e   e n e r g y , a n d
o n   m i c r o w a v e   e n e r g y , a n d           f o l l o w
o n   m i c r o w a v e   e n e r g y , a n d
m a y           e x p o s e
m a y
m a y
e x p o s e
e x p o s e
e x p o s e           y o u r s e l f
y o u r s e l f
y o u r s e l f           t o t o t o t o t o           t h e
y o u r s e l f
m a y
e x p o s e
y o u r s e l f
P R E C A U T I O N S
P R E C A U T I O N S
P R E C A U T I O N S
P R E C A U T I O N S
P R E C A U T I O N S
A N D           D U R I N G
A N D
A N D
A N D
D U R I N G
D U R I N G
D U R I N G           S E R V I C I N G
D U R I N G
S E R V I C I N G           T O
S E R V I C I N G
S E R V I C I N G
S E R V I C I N G
E N E R G Y
E N E R G Y
E N E R G Y
E N E R G Y
EM‑CD2900(UK)
EM‑CD2900(UK)
EM‑CD2900(UK)
EM‑CD2900(UK)
EM‑CD2900(UK)
Pro.Code No.   Model No.
437 644 00    EM‑CD2900UK
f o l l o w
f o l l o w
f o l l o w           t h e
f o l l o w
t h e
t h e
t h e           m i c r o w a v e
m i c r o w a v e
m i c r o w a v e           e n e r g y
m i c r o w a v e
t h e
m i c r o w a v e
T O
T O
T O           A V O I D
T O
A V O I D           P O S S I B L E
A V O I D
A V O I D
A V O I D
REFERENCE  NO.
REFERENCE  NO.
REFERENCE  NO.
REFERENCE  NO.
REFERENCE  NO.
t h e
t h e
t h e
t h e          p r o c e d u r e
p r o c e d u r e
p r o c e d u r e
p r o c e d u r e
p r o c e d u r e
e n e r g y           l e a k a g e .
e n e r g y
e n e r g y
l e a k a g e .
l e a k a g e .
l e a k a g e .
e n e r g y
l e a k a g e .
P O S S I B L E
P O S S I B L E
P O S S I B L E
P O S S I B L E
SM‑6310034‑00
 

Advertisement

Table of Contents
loading

Summary of Contents for Sanyo EM-CD2900UK

  • Page 1 SERVICE SERVICE SERVICE          MANUAL MANUAL MANUAL MANUAL SERVICE SERVICE MANUAL EM‑CD2900(UK) EM‑CD2900(UK) EM‑CD2900(UK) EM‑CD2900(UK) EM‑CD2900(UK) COMMERCIAL COMMERCIAL COMMERCIAL          USE USE          COMBINATION COMBINATION COMBINATION COMMERCIAL COMMERCIAL COMBINATION COMBINATION MICROWAVE MICROWAVE MICROWAVE  ...
  • Page 2: Table Of Contents

    ‑ TABLE OF CONTENTS ‑ ‑ TABLE OF CONTENTS ‑ ‑ TABLE OF CONTENTS ‑ ‑ TABLE OF CONTENTS ‑ ‑ TABLE OF CONTENTS ‑ 1.Adjustment Procedures....1  7.Test Procedures and Troubleshooting...5‑14 2.Specifications......2  8.Disassembly Instructions.....15‑22 3.Power output Measurement....2  9.Exploded View and Parts List..23‑30 4.Precautions and Repair Service Tips...2 10.Overall Circuit Diagram....31‑32 5.Oven Control Panel....3 11.Control Circuit Diagram....33 6.Circuit Diagram.......4 (5)Make sure the interlock monitor switch                CAUTION  CAUTION  CAUTION  CAUTION  CAUTION     opens before the primary interlock switch  MICROWAVE RADIATION  MICROWAVE RADIATION  MICROWAVE RADIATION  MICROWAVE RADIATION  MICROWAVE RADIATION closes when the door is closed very slowly, according  to CHECKOUT  PROCEDURE  FOR PERSONNEL SHOULD NOT BE EXPOSED TO THE PERSONNEL SHOULD NOT BE EXPOSED TO THE PERSONNEL SHOULD NOT BE EXPOSED TO THE PERSONNEL SHOULD NOT BE EXPOSED TO THE PERSONNEL SHOULD NOT BE EXPOSED TO THE...
  • Page 3: Specifications

    (1)Before the power is applied. 2. SPECIFICATIONS 2. SPECIFICATIONS 2. SPECIFICATIONS 2. SPECIFICATIONS 2. SPECIFICATIONS (a)Open and close door several times to Rated Power Consumption.. Microwave 1200W make sure the door interlock switch Heater 1300W and interlock monitor switch operation Combi 2500W properly.(Listen for the clicking sound Microwave output..800W from switches.) Make sure the inter‑ Frequency....2,450MHz ± 50MHz lock monitor switch is closed after Power supply..... 230V,50Hz the latch interlock switch is open when Rated current.... 5.5 ± 10% Amps Micro the door is opened. (After 15 mins.)    (See pages 1 and 6) 5.6 ± 10% Amps Heater (After 15mins.) (b)Make sure the perforated screen and 11.0 ± 10% Amps Combi the choke dielectric of the door are (After 15 mins.) correctly mounted.
  • Page 4: Oven Control Panel

    5.OVEN CONTROL PANEL 5.OVEN CONTROL PANEL 5.OVEN CONTROL PANEL 5.OVEN CONTROL PANEL 5.OVEN CONTROL PANEL ‑ 3 ‑...
  • Page 5: Circuit Diagram

    6.CIRCUIT DIAGRAM 6.CIRCUIT DIAGRAM 6.CIRCUIT DIAGRAM 6.CIRCUIT DIAGRAM 6.CIRCUIT DIAGRAM Figure 2 * Caution :The voltage between filament leads of magnetron is about 3.3VA.C, but the   filament carries 4KV D.C high voltage with respect to grand. Never touch these lead   with bare hand during operation. ‑ 4 ‑...
  • Page 6: Caution

    7. TEST PROCEDURES AND TROUBLESHOOTING 7. TEST PROCEDURES AND TROUBLESHOOTING 7. TEST PROCEDURES AND TROUBLESHOOTING 7. TEST PROCEDURES AND TROUBLESHOOTING 7. TEST PROCEDURES AND TROUBLESHOOTING CAUTION CAUTION CAUTION CAUTION CAUTION ‑ DISCONNECT THE POWER SUPPLY CORD FROM THE WALL ‑ DISCONNECT THE POWER SUPPLY CORD FROM THE WALL ‑ DISCONNECT THE POWER SUPPLY CORD FROM THE WALL ‑ DISCONNECT THE POWER SUPPLY CORD FROM THE WALL ‑ DISCONNECT THE POWER SUPPLY CORD FROM THE WALL   OUTLET WHENEVER RMOVING THE CABINET FROM THE   OUTLET WHENEVER RMOVING THE CABINET FROM THE   OUTLET WHENEVER RMOVING THE CABINET FROM THE   OUTLET WHENEVER RMOVING THE CABINET FROM THE   OUTLET WHENEVER RMOVING THE CABINET FROM THE   UNIT.   UNIT.   UNIT.   UNIT.   UNIT.   PROCEED WITH TESTS ONLY AFTER DISCHARGING THE   PROCEED WITH TESTS ONLY AFTER DISCHARGING THE   PROCEED WITH TESTS ONLY AFTER DISCHARGING THE   PROCEED WITH TESTS ONLY AFTER DISCHARGING THE   PROCEED WITH TESTS ONLY AFTER DISCHARGING THE   HIGH VOLTAGE CAPACITOR AND REMOVING THE LEAD   HIGH VOLTAGE CAPACITOR AND REMOVING THE LEAD   HIGH VOLTAGE CAPACITOR AND REMOVING THE LEAD   HIGH VOLTAGE CAPACITOR AND REMOVING THE LEAD   HIGH VOLTAGE CAPACITOR AND REMOVING THE LEAD   WIRES ON THE PRIMARY WINDING OF THE HIGH VOL‑   WIRES ON THE PRIMARY WINDING OF THE HIGH VOL‑   WIRES ON THE PRIMARY WINDING OF THE HIGH VOL‑   WIRES ON THE PRIMARY WINDING OF THE HIGH VOL‑   WIRES ON THE PRIMARY WINDING OF THE HIGH VOL‑   TAGE TRANSFORMER.(SEE FIGURE 3)   TAGE TRANSFORMER.(SEE FIGURE 3)   TAGE TRANSFORMER.(SEE FIGURE 3)
  • Page 7 COMPONENT COMPONENT COMPONENT CHECKOUT PROCEDURE CHECKOUT PROCEDURE COMPONENT COMPONENT CHECKOUT PROCEDURE CHECKOUT PROCEDURE CHECKOUT PROCEDURE RESULT RESULT RESULT RESULT RESULT 1) Measure the resistance: Normal reading: HIGH ‑ VOLTAGE HIGH ‑ VOLTAGE HIGH ‑ VOLTAGE HIGH ‑ VOLTAGE HIGH ‑ VOLTAGE     With an ohm meter on Rx1 scale. a. Approximately 1.0 ohms. TRAMSFORMER TRAMSFORMER TRAMSFORMER TRAMSFORMER TRAMSFORMER  a. Primary winding; b. Less than 1 ohm.  b. Filament winding; c. Approximately 60 ohms.  c. Secondary winding; 2) Measure the resistance: Normal reading:     With an ohm meter on highest scale. a. Infinite ohms.  a. Primary winding to ground; b. Infinite ohms.  b. Filament winding to ground;...
  • Page 8 COMPONENT COMPONENT CHECKOUT PROCEDURE CHECKOUT PROCEDURE COMPONENT COMPONENT COMPONENT CHECKOUT PROCEDURE CHECKOUT PROCEDURE CHECKOUT PROCEDURE RESULT RESULT RESULT RESULT RESULT Measure the resistance between TOUCH KEY TOUCH KEY TOUCH KEY TOUCH KEY TOUCH KEY terminals of FPC connector after When When not BOARD BOARD BOARD BOARD BOARD removing it from S101.(Figure 10) touched touched Resistance    NOTE Value Less than More than ‑When reconnecting the FPC connector, 1K ohms 1M ohms  make sure the holes on the connector  are properly inserted in hook of the When checking the Grill key,connect...
  • Page 9 CHECKOUT PROCEDURE FOR SWITCHES CHECKOUT PROCEDURE FOR SWITCHES CHECKOUT PROCEDURE FOR SWITCHES CHECKOUT PROCEDURE FOR SWITCHES CHECKOUT PROCEDURE FOR SWITCHES Disconnect the lead wires from the switches and check for the continuity of the switches, connecting an ohm‑meter to its terminals. SWITCHES SWITCHES SWITCHES SWITCHES SWITCHES CHECKOUT PROCEDURE CHECKOUT PROCEDURE CHECKOUT PROCEDURE CHECKOUT PROCEDURE CHECKOUT PROCEDURE DOOR OPEN DOOR OPEN DOOR CLOSE DOOR CLOSE DOOR OPEN DOOR OPEN DOOR OPEN DOOR CLOSE DOOR CLOSE DOOR CLOSE (See Figure 1 on page 1) (See Figure 1 on page 1) (See Figure 1 on page 1) (See Figure 1 on page 1) (See Figure 1 on page 1) INTERLOCK INTERLOCK INTERLOCK INTERLOCK INTERLOCK Terminals COM and NO DOOR SENSING DOOR SENSING DOOR SENSING...
  • Page 10 B. TROUBLE SHOOTING B. TROUBLE SHOOTING B. TROUBLE SHOOTING B. TROUBLE SHOOTING B. TROUBLE SHOOTING ‑ 9 ‑...
  • Page 11 ‑ 10 ‑...
  • Page 12 ‑ 11 ‑...
  • Page 13 ‑ 12 ‑...
  • Page 14 ‑ 13 ‑...
  • Page 15 C. ERROR INDICATION C. ERROR INDICATION C. ERROR INDICATION C. ERROR INDICATION C. ERROR INDICATION The Display will show an error indication for self diagnosis as follows. "E" means that a service technician is required. "U" means that user can correct the operation. Display Trouble Other Symptom Solution ●Check for relay circuit board on Blower motor. ●Microwave relay is welded. ●Oven stops heating. E-12 ●Magnetron thermistor in mode heater ●Buzzer continuously beeps. → This error function will be cancelled when the a temperature of 90℃...
  • Page 16: Disassembly Instructions

    8. DISASSEMBLY INSTRUCTIONS 8. DISASSEMBLY INSTRUCTIONS 8. DISASSEMBLY INSTRUCTIONS C.REMOVING  FUSE C.REMOVING  FUSE C.REMOVING  FUSE 8. DISASSEMBLY INSTRUCTIONS 8. DISASSEMBLY INSTRUCTIONS C.REMOVING  FUSE C.REMOVING  FUSE Remove the 15A fuse with screwdriver. ‑ OVEN MUST BE DISCONNECTED FROM ELECTRICAL ‑ OVEN MUST BE DISCONNECTED FROM ELECTRICAL ‑ OVEN MUST BE DISCONNECTED FROM ELECTRICAL ‑ OVEN MUST BE DISCONNECTED FROM ELECTRICAL ‑ OVEN MUST BE DISCONNECTED FROM ELECTRICAL NOTES NOTES NOTES NOTES NOTES OUTLET WHEN MAKING REPLACEMENTS, REPAIRS, OUTLET WHEN MAKING REPLACEMENTS, REPAIRS, OUTLET WHEN MAKING REPLACEMENTS, REPAIRS, OUTLET WHEN MAKING REPLACEMENTS, REPAIRS, OUTLET WHEN MAKING REPLACEMENTS, REPAIRS, ‑ When replacing the 15A fuse, be sure to use ADJUSTMENT AND CONTINUITY CHECKS BEFORE PRO‑ ADJUSTMENT AND CONTINUITY CHECKS BEFORE PRO‑ ADJUSTMENT AND CONTINUITY CHECKS BEFORE PRO‑ ADJUSTMENT AND CONTINUITY CHECKS BEFORE PRO‑ ADJUSTMENT AND CONTINUITY CHECKS BEFORE PRO‑   an exact repair part. CEEDING WITH ANY REPAIR WORK AFTER DISCON‑ CEEDING WITH ANY REPAIR WORK AFTER DISCON‑ CEEDING WITH ANY REPAIR WORK AFTER DISCON‑ CEEDING WITH ANY REPAIR WORK AFTER DISCON‑ CEEDING WITH ANY REPAIR WORK AFTER DISCON‑ ‑ If the 15A fuse blows immediately, check NECTING, WAIT AT LEAST 1 MINUTE, UNTIL THE NECTING, WAIT AT LEAST 1 MINUTE, UNTIL THE NECTING, WAIT AT LEAST 1 MINUTE, UNTIL THE NECTING, WAIT AT LEAST 1 MINUTE, UNTIL THE...
  • Page 17 E. E. E. E. E.REMOVING CONTROL CIRCUIT BOARD REMOVING CONTROL CIRCUIT BOARD REMOVING CONTROL CIRCUIT BOARD REMOVING CONTROL CIRCUIT BOARD REMOVING CONTROL CIRCUIT BOARD (1) Disconnect all connector and lead wires from     the control circuit board. Remove 4 screws (2) Remove 2 screws securing the tabs for earthing and FPC connector     to the oven cavity. (3) Remove 2 screws securing the control panel as‑     sembly to the oven cavity. (4) Push up and then pull out the control panel     assembly. (5) Disconnect all lead wires of the control panel     from the control PCB.(S105,S106,S102,S1 con‑     nector for the relay PCB) Figure 11 Release the hook one by one F. F. F. F. F.REMOVING TOUCH KEY BOARD AND TIME CONTROLLER REMOVING TOUCH KEY BOARD AND TIME CONTROLLER REMOVING TOUCH KEY BOARD AND TIME CONTROLLER REMOVING TOUCH KEY BOARD AND TIME CONTROLLER REMOVING TOUCH KEY BOARD AND TIME CONTROLLER  After removing control circuit board;...
  • Page 18 H.REMOVING  MAGNETRONS H.REMOVING  MAGNETRONS H.REMOVING  MAGNETRONS H.REMOVING  MAGNETRONS H.REMOVING  MAGNETRONS Remove 6 screws (1) Disconnect all lead wires from the thermal     protector. (2) Remove 4 screws securing the duct for magne‑   tron.(Figure 15) (3) Take off the duct for magnetron.(Figure 16) (4) Disconnect 2 lead wires from the magnetron      terminals by removing 2 connectors. (5) To remove nuts securing magnetron fittings,     insert the long size box wrench in the 10 mm     diameter hole located at the parts base of the     rear side as shown in figure 19.     Loose 2 nuts.(Figure 17) Figure 15 (6) Remove thermistor for magnetron from the radi‑     ant fin. Take off the duct from the magnetron (7) Take out the magnetron VERY CAREFULLY VERY CAREFULLY VERY CAREFULLY VERY CAREFULLY VERY CAREFULLY. (8) After replacing the magnetron, make sure that After replacing the magnetron, make sure that After replacing the magnetron, make sure that After replacing the magnetron, make sure that After replacing the magnetron, make sure that the insert position of thermistor for magne‑...
  • Page 19 I I I I I .CHANGING  POWER  SUPPLY  CORD .CHANGING  POWER  SUPPLY  CORD .CHANGING  POWER  SUPPLY  CORD .CHANGING  POWER  SUPPLY  CORD .CHANGING  POWER  SUPPLY  CORD Remove 1 screw for the bottom plate (See exploded view on page 25) of the cord bushing. (1) Unfasten 1 screw for ground and pull out     the 2 wires of the power cord from the     noise filter. (2) Remove 1 screw for the stay plate of the     cord bushing. (3) Install the new power supply cord with the     reverse procedure of above(1)to(2). WARING; WARING; WARING; WARING; WARING; For changing the power supply cord,never use other than the following.     Key No.     Order No.        Parts name 24       617 180 3211   Cord bush Figure 20 25        617 275 2624    Cord assembly 26        917 140 1340    Stay plate Remove 2 screws with 7 mm box wrench.
  • Page 20 K.REMOVING  DOOR K.REMOVING  DOOR K.REMOVING  DOOR K.REMOVING  DOOR K.REMOVING  DOOR L. DISASSEMBLY  DOOR L. DISASSEMBLY  DOOR L. DISASSEMBLY  DOOR L. DISASSEMBLY  DOOR L. DISASSEMBLY  DOOR Remove 3 hex nuts securing the upper hinge,    (1)Insert a thin flat blade screw driver remove 3 hex nuts securing the lower hinge between the choke dielectric and the and remove 1 special screw securing the door door assembly comp.and lift up the arm (located at the bottom of the door sash) choke dielectric to release the hook one by one.            NOTES  (2)To remove door cover,remove the 14 screws securing the door cover to the door ‑  After replacing the door, be sure to check assembly comp. that the primary interlock switch, the door    (3)Remove 1 screw securing the cover as‑ sensing switch and the interlock monitor sembly to the door assembly comp. switch operate normally.        (Figure 23‑(a)) (See pages 1 and 8)    (4)Insert a thin flat blade screwdriver ‑  After replacing the door, check for micro‑        between the door base and door as‑ wave energy leakage with a leakage detector.        sembly comp.and release the hook one Microwave energy leakage must be below the by one. limit of 5mW/cm     (5)To detach the cover assembly,insert        a thin flat blade screwdriver between        the door panel and door cover,and        release the clip one by one.
  • Page 21 O. RELEASING TYPE CONNECTOR O. RELEASING TYPE CONNECTOR O. RELEASING TYPE CONNECTOR O. RELEASING TYPE CONNECTOR O. RELEASING TYPE CONNECTOR M.HOW TO RESET THE MEMORY OF ACCUMULATIVE M.HOW TO RESET THE MEMORY OF ACCUMULATIVE M.HOW TO RESET THE MEMORY OF ACCUMULATIVE M.HOW TO RESET THE MEMORY OF ACCUMULATIVE M.HOW TO RESET THE MEMORY OF ACCUMULATIVE COOKING TIME COOKING TIME COOKING TIME COOKING TIME COOKING TIME This oven is provided with locked type After replacing the magnetron, reset each of connector. When you remove a connector, the accumulative cooking time. pull the connector while releasing the lock by pressing  A  point shown below. 1. Touch       key. Do not pull the wire of the connector. 2. Open and close the door, touch             and  M key at the same time. 3. Push " 8 "," 8 "," 8 "," 1 ","     ","    ".    The display will show each of the accumula‑    tive cooking time which is selected in the    display window by the sign      . 4. Each of the accumulative cooking time will be selected by pressing the ...
  • Page 22 L. ADDITIONAL FUNCTIONS L. ADDITIONAL FUNCTIONS L. ADDITIONAL FUNCTIONS L. ADDITIONAL FUNCTIONS L. ADDITIONAL FUNCTIONS The following functions can be completed by the key operation described below. The Accumulative cooking time and the number of door openings/closings can be observed. The Type and level of the buzzer sound can be selected. The display of remaining cooking time when cooking is temporarily stopped due to door opening  can be selected. The Accumulative cooking time period will inform the service technician of the life ex‑ pectation of the magnetron or other parts. Key operation SET FOR VARIOUS MODES Display shows accumulative cooking time or the number of door operations by key operation. Also, you can change any remaining cooking time, buzzer sound or buzzer volume, etc.
  • Page 23 Maintenance: The microwave ovens are designed, manufactured, and tested for years of dependable operation. However,the oven may require service from time to time if the consumable components listed below are not replaced at the appropriate time. For protection from unexpected service calls and undue inconvenience, we recommend that the user has the listed parts replaced at the intervals belows, (at customer cost).This will avoid the trouble of repeated service calls after the expiration of the warranty period. Consumable components: When more than 1,250 hours of accumulative cooking time or more than 200,000 cycles of door opening/closing is observed by key operations (See page 21 for more information), the following consumable components should be replaced.(Maintenance sign in window display indicates when accumulative cooking time reaches 1,250 hours.) 1. Magnetron Tube, Part No. 315 003 3300 (No.19 on page 26) 2. Printed Circuit Board‑Relay, Part No. 617 274 7507(No.33 on page 26) 3. Switch base Assembly, Part No. 917 275 8184 (No.53 on page 26) 4. Door Latch, part No. 617 068 1087 (No.213 on page 29)  * When more than 2,000 hours of accumulative cooking time is observed, the following    consumable components should be replaced. 5. Blower motor, Part No. 917 232 4693 (No.32 on page 26)     When slow rotating of blower motor is observed after removing dust from blower motor,     blower motor must be replaced. 6. Door hinge, Part No. 917 120 3029 (No.216 on page 29)     When a worn door hinge is observed and proper door adjustments can not be made,the door     hinge must be replaced. ‑ 22 ‑...
  • Page 24: Exploded View And Parts List

    9. EXPLODED VIEW AND PARTS LIST 9. EXPLODED VIEW AND PARTS LIST 9. EXPLODED VIEW AND PARTS LIST 9. EXPLODED VIEW AND PARTS LIST 9. EXPLODED VIEW AND PARTS LIST     Main  body  Parts‑1     Main  body  Parts‑1     Main  body  Parts‑1     Main  body  Parts‑1     Main  body  Parts‑1 3x 8 3x 8 Parts marked with this sign have special characteristics important for microwave leakage. When replacing any of these parts use only manufacturers specified parts. ‑ 23 ‑...
  • Page 25 Main  body  Parts‑1 Main  body  Parts‑1 Main  body  Parts‑1 Main  body  Parts‑1 Main  body  Parts‑1 KEY No. SERVICE PARTS DESCRIPTION Q'TY 617 275 2044 CABINET SUS430 T0.6 NO.4 617 123 9942 INSU. SHEET 617 232 0199 PACKING 617 234 2375 FRAME PLATE ASS'Y 617 232 0267 PACKING...
  • Page 26             Main  body  Parts‑2     Main  body  Parts‑2             Main  body  Parts‑2         Main  body  Parts‑2     Main  body  Parts‑2 Parts marked with this sign have special characteristics important for microwave leakage. When replacing any of these parts use only manufacturers specified parts. ‑ 25 ‑...
  • Page 27 Main  body  Parts‑2 Main  body  Parts‑2 Main  body  Parts‑2 Main  body  Parts‑2 Main  body  Parts‑2 917 276 8190 HV CAPACITOR HANSUNG CHN0.85/2600 917 140 1265 THERMOSTAT 617 234 0883 PACKING 617 275 2679 MAGNETRON FITTINGS SECC T2.0 315 003 3300 MAGNETRON 2M281H(M) TOSB 617 123 4688...
  • Page 28 Main  body  Parts‑3 Main  body  Parts‑3 Main  body  Parts‑3 Main  body  Parts‑3 Parts marked with this sign are supplied with high voltage exceeding 250V. Parts marked with this sign have special characteristics important for microwave leakage. When replacing any of these parts use only manufacturers specified parts. EM-CD2900UK KEY No. SERVICE PARTS DESCRIPTION Q'TY 617 275 2662 H.V.TRANSFORMER N5T-CD2900 917 195 1296 SPECIAL WASHER BRASS T1.0 NI PLATIN...
  • Page 29 C o n t r o l   p a n e l   P a r t s C o n t r o l   p a n e l   P a r t s Parts marked with this sign have special characteristics important for microwave leakage. When replacing any of these parts use only manufacturers specified parts. EM-CD2900UK Key No. SERVICE PARTS DESCRIPTION Q'TY 617 224 8745 KNOB ASS'Y...
  • Page 30 Main  body  Parts‑5 Main  body  Parts‑5 Main  body  Parts‑5 Main  body  Parts‑5 Door  Parts Door  Parts Door  Parts Door  Parts Door  Parts EM-CD2900UK KEY No. SERVICE PARTS DESCRIPTION Q'TY 617 201 9697 DOOR HANDLE 617 280 7416 ORNAMENT PLATE 617 280 7409...
  • Page 31 ACCESARIES KEY No. SERVICE PARTS DESCRIPTION Q'TY 617 121 5533 SHELF 617 275 2730 COOK NET ASS'Y 617 195 1332 PRECAUTION LABEL 617 280 7461 MENU LABEL 617 275 2778 INST. MANUAL Accesaries Item No.401‑ No.405  are not illustrated. ‑ 30 ‑...
  • Page 32: Overall Circuit Diagram

    10. OVERALL CIRCUIT DIAGRAM 10. OVERALL CIRCUIT DIAGRAM 10. OVERALL CIRCUIT DIAGRAM 10. OVERALL CIRCUIT DIAGRAM 10. OVERALL CIRCUIT DIAGRAM ‑ 31 ‑...
  • Page 33 ‑ 32 ‑...
  • Page 34: Control Circuit Diagram

    11.CONTROL  CIRCUIT  BOARD 11.CONTROL  CIRCUIT  BOARD 11.CONTROL  CIRCUIT  BOARD 11.CONTROL  CIRCUIT  BOARD 11.CONTROL  CIRCUIT  BOARD J101 J102 J103 J104 C113 D112 R122 C109 D113 C111 J108 J107 J109 R117 R119 ZD101 D114 R156 J154 R158 C102 R155 R157 C108 R114 D103 R130 C106...
  • Page 35 M e m o M e m o M e m o M e m o M e m o ‑ 34 ‑...
  • Page 36 SANYO Electric Co.,Ltd. OSAKA Japan ‑ 35 ‑...

This manual is also suitable for:

437 644 00

Table of Contents