Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Symbol LL 425
Summary of Contents for Symbol LL 425
- Page 1 RS 2200/3200 Series LL 425 Quick Reference...
- Page 2 Symbol reserves the right to make changes to any product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
- Page 3 Connect the appropriate interface cable assembly. See the LL 425 Interface Guide for more information. When the host can provide sufficient power for the LL 425 and a 5V scanner, the interface cable assembly is set up at the factory with a Power Selection Plug installed.
- Page 4 Programmable Parameters and Defaults Parameter Default Code Types Code Lengths Code 39 1 to 55 Code 128 3 to 55 Codabar 2 to 55 I 2 of 5 D 2 of 5 MSI Plessey 1 to 55 Decode Options Transmit UPC-A Check Digit Enabled Transmit UPC-E Check Digit Enabled...
- Page 5 Programmable Parameters and Defaults Parameter Default Prefix/Suffix Values 7013 (<Enter> for serial devices Scan Data Xmission Format Data as is Magstripe Data Xmission Format Data as is Laser Control Trigger Mode Level Laser On Time-out 1 Sec Laser Off Time-out 1 Sec RS-232C Single Port Baud Rate...
-
Page 6: Host Selection
Host Selection Each Interface Cable Asembly will default the LL 425 to a given host. Below is a list of the assemblies and their corresponding default hosts. If your host type is not listed below, you must select it by scanning the appropriate bar code beginning on page page 10. -
Page 7: Customizing The Data
Customizing the Data If you want to append an ENTER (CR) to all data, scan the five bar codes below, starting at the top and working down. When you do this, all previously stored ADF rules will be deleted. ERASE ALL RULES ANY SOURCE SEND ALL DATA SEND ENTER... -
Page 8: What Does The Beep Mean
• Refer to the WHAT IF... table on the next page. • Find the symptom and check the items marked with an “x”. If, after performing these checks the symbol still does not scan, contact the technical person in charge of scanning. Quick Reference... - Page 9 What If... Check Proper Cable Position of J4 Correct Terminal Type Programmed? Power to Host System? Cable Connected To Host? Power Selection Plug Inserted? Power Supply Plugged In? Quick Reference...
-
Page 10: Host Types
Host Types IBM PC/AT and Clones Fujitsu 9000 IBM PS2/50/55SX/60/70/80 IBM PS2/30 Wedge IBM PC/XT Wedge and Clones IBM 4683/4684 Port 5B IBM 4683/4684 Port 9B IBM 4683/4684 Port 17 Quick Reference... - Page 11 Host Types IBM 3683/3684 35-Key Calc Wedge IBM 3683/3684 48-Key CalcWedge IBM 3683/3684 116-Key CalcWedge IBM 3683/3684 35-Key Tel Wedge IBM 3683/3684 48-Key Calc Wedge IBM 3683/3684 116-Key Calc Wedge Quick Reference...
- Page 12 Host Types NCR 2151 Tel Wedge NCR 2151 Calc Wedge NCR 2152 Tel Wedge NCR 2152 Calc Wedge NCR 7052 Wedge Quick Reference...
- Page 13 Host Types Fujitsu 7770/7880 7990/8770/9000 IBM 3653/3683/3684/5365 NCR 255/1255/2152/2154 2155/2126-1120/2126-1320 2157/2257/7000/7050/7051 7052 “S” OCIA NCR 2950 “S” OCIA NCR 7052 “F” OCIA Nixdorf 8812 OCIA Quick Reference...
- Page 14 Host Types ICL 9518/9520 OCIA Standard RS-232C ICL RS-232C Nixdorf RS-232C Quick Reference...
-
Page 15: Regulatory Information
If you have a problem with running your terminal or using your equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Symbol Support Center: 1-800-653-5350 Outside North America, contact your local Symbol representative. Quick Reference... -
Page 16: Warranty
This warranty is provided to the original owner only and is not transferable to any third party. It shall not apply to any product (i) which has been repaired or altered unless done or approved by Symbol, (ii) which has not been maintained in accordance with any operating or handling instructions supplied...