Erasing Learned Commands - Harman Kardon AVR35RDS User Manual

To program the AVR35RDS remote,
follow these steps:
1. Press and hold the
Device Control
for the product type you
Selector c
wish to program (e.g., TV, VCR, etc.) and
the button at the same time
j
Set
until the
Program/Command
turns orange and the red
Indicator a
LED under the
Device Control
lights. Both should remain lit.
Selector
2. Within 20 seconds, press the button
on the AVR35RDS remote that you
wish to assign a learned command.
It is always a good idea to start with
d
the button , though you
Power
may teach the buttons in any order
that you wish. Note that the orange
Program/Command Indicator a
will begin to flash continuously, and
the LED under the
Device Control
Selector c will go out.
3. Point the LED transmitter from the
source remote control towards the
front of the AVR35RDS remote. Press
and hold the button to be learned
until the
Program/Command
briefly flashes green,
Indicator a
and returns to a constant orange color.
Release the button on the source
remote control.
4. Verify that the command has been
learned correctly by pressing and hold-
ing the same button on the source
remote control once again. Release the
button on the source remote when the
Program/Command Indicator a
flashes green twice, and then returns
AVR35RDS 230 volt Rev (C) 9/28/98
Programming the Remote
31
to a constant orange color. This
indicates that the IR code was pro-
grammed from the source remote to
the AVR35RDS remote successfully. The
red LED under the
Device Control
will illuminate again,
Selector c
to indicate that the AVR35RDS remote
is ready to be programmed for another
button command.
5. Repeat steps 2 through 4 for each
button command that you wish to
transfer from the source remote to the
AVR35RDS remote for this specific
source device.
6. When all desired commands have been
taught from the source remote to the
AVR35RDS remote, press and hold the
Device Control Selector c
the button at the same time
j
Set
until the
Program/Command
Indicator a flashes twice, and then
goes out, and the red LED under the
Device Control Selector
This indicates that the codes have been
saved to the AVR35RDS remote's memory.
7. Follow steps 1 through 6 to program
the AVR45 RDS remote for the codes
from a different source remote.

Erasing Learned Commands

The AVR35RDS remote allows you to edit
the command functions by erasing a sin-
gle command within one device, to erase
all commands for a single device, or to
erase all commands that have been pro-
grammed into the memory of the remote
for all devices.
Erasing A Single Learned Command
To erase a single command from those
memorized for a specific device follow
these steps:
1. Press the
Device Control Selector
for the desired device (e.g., TV,
c
VCR, etc.) and the
at the same time until the LED under
the
Device Control Selector
red and the
Program/Command
Indicator a
orange.
2. Press the button on the AVR35RDS
remote for which you wish to have the
code erased. The red LED under the
Device Control Selector c
go out and the
and will flash orange.
Indicator
3. Press the
Direct
Program/Command Indicator
flash green twice, and then turn to a
turns off. steady orange color. The red LED
under the
Device Control Selector
will turn back on.
c
4. Repeat steps 2 and 3 for any other
buttons where you wish to erase the
code that has been programmed.
5. When you are finished erasing any
codes that need to be erased, press and
hold the
Device Control Selector
and the
c
Set
same time. The red LED under the
Device Control Selector
off and the
Program/Command
Indicator a
then turn off.
button j
Set
turns
turns and remains
will
Program/Command
button . The
s
will
button at the
j
will turn
will flash twice and