Page 1
19T2 SERVICE MANUAL AEP Model Chassis No. SCC-L30T-A CHASSIS SPECIFICATIONS Dimensions and weight CRT: 46 cm (19") Visible diagonals: 46 cm Dot pitch: 0.24 - 0.25 mm (slot mask) Maximal resolution: 1600 x 1200 pixels Preset display area: 352 mm x 264 mm...
Page 2
19T2 SAFETY CHECK-OUT After correcting the original service problem, perform the fol- LEAKAGE TEST lowing safety checks before releasing the set to the customer: The AC leakage from any exposed metal part to earth ground 1. Check the area of your repair for unsoldered or poorly-sol- and from all exposed metal parts to any exposed metal part hav- dered connections.
Page 3
19T2 POWER SAVING FUNCTION If your PC has a VESA DPMS (Video Electronics Standard Association, Display Power Management Signaling) power management function (energy-saving mode), your monitor will fully support this function. The monitor has a four-stage power management system. Stage...
Page 4
19T2 TIMING SPECIFICATION MODE AT PRODUCTION MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6 RESOLUTION 720 X 400 640 X 480 640 X 480 800 X 600 800 X 600 1024 X 768 CLOCK 28.325 MHz 25.175 MHz...
Operating Instruction Manual. The page numbers of GENERAL the Operating Instruction Manual remain as in the manual. Color monitor 19T2 Color monitor 19T2 Installing an ergonomic video workstation Before you set up your equipment you should select a suitable position for working at the monitor.
Page 7
Color monitor 19T2 Color monitor 19T2 If your PC detects inactivity (no input) it sends an appropriate signal to the monitor to reduce the Operation of the monitor power consumption. The power indicator of the monitor changes color to indicate the status change.
Page 8
Color monitor 19T2 Color monitor 19T2 Operating the OSD menu Setting the brightness of the background To set the OSD menu, perform the following steps: Briefly press the Menu button to activate the OSD menu. Setting the contrast between the foreground and background The main menu appears on the screen with icons for the setting functions.
Page 9
Color monitor 19T2 Color monitor 19T2 Setting language for the OSD menu (LANGUAGE) Trapezoid distortion (KEYSTONE): Making the bottom edge narrower and the top edge wider or making the top edge narrower and the bottom edge wider Setting language for the OSD menu...
Page 10
Color monitor 19T2 Color monitor 19T2 Resetting all settings for the current input signal Restore original monitor colors (COLOR RETURN) Press - with the OSD menu hidden - the factory settings button After a number of years of operation the color brightness of your monitor may All settings for the current input signal are reset.
Page 11
Dot pitch: 0.24 - 0.25 mm (slot mask) If the monitor 19T2 is not yet displayed in the list of monitors, you can select one of the Maximal resolution: 1600 x 1200 pixels following monitors instead:...
Page 12
Color monitor 19T2 Color monitor 19T2 Pin assignment D-SUB (15-pin) Error handling Should an error occur, first check the following points. If the distortion is still not eliminated, the monitor should, if possible, be checked on another PC. Self-diagnosis The monitor is equipped with a self-diagnosis function. If the monitor recognizes a fault, the screen display remains dark and the power indicator glows green or flashes orange.
Page 13
Color monitor 19T2 Color monitor 19T2 Two fine horizontal lines (wires) are visible A humming noise is heard after switch-on The monitor is degaussed every time you switch it on. This produces the humming noise. There is Your monitor is equipped with a Trinitron picture tube, which enables more light to reach no malfunction.
19T2 SECTION 2 DISASSEMBLY 2-1. CABINET REMOVAL Push in the tip of a screwdriver about 5mm to unlock the two claws. Cabinet Cabinet Two claws Bezel assembly Bezel assembly Cabinet Two screws (+BVTP 4 x 16) Two claws EMI shield (Upper) 2-2.
19T2 2-3. A BOARD REMOVAL A board CN306 CN311 CN303 CN309 Three screws (+BVTT 3 x 8) CN305 Screw (+BVTT 4 x 8) Cable stopper Two screws 2-4. REAR SHIELD COMPLETE ASSY, (+BVTP 3 x 8) D BOARD REMOVAL Screw (+P 3.5 x 20)
19T2 2-5. SERVICE POSITION A board D board AC inlet 2-6. H BOARD REMOVAL Before removing the bezel assembly, secure the picture tube shield at the positions shown with the arrow (diagonal two places) to prevent the picture tube Four screws (Tapping screw(5)) from falling.
19T2 2-7. PICTURE TUBE REMOVAL Four screws (Tapping screw (5)) Anode cap A board 2pin Neck assembly CN11 Three connectors Deflection yoke Picture tube Bezel assembly CN801 • REMOVAL OF ANODE-CAP NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after removing the anode.
19T2 SECTION 3 SAFETY RELATED ADJUSTMENT When replacing or repairing parts in the table shown be- b) High Voltage Hold-Down Function Check low, the following operational checks must be performed + 0.00 1) Apply the voltage 21.1 VDC between D912 cath- –...
19T2 SECTION 4 ADJUSTMENTS • Landing Rough Adjustment 13. Using two wedges, adjust vertical pins so as to attain a=b as 1. Enter the full white signal. (or the full black dots signal). shown below. Further, insert two wedges as shown in the 2.
Page 21
19T2 Connect the communication cable of the computer to the connector located on the D board on the monitor. Run the service software and then follow the instruction. 1-690-391-21 A-1500-819-A 3-702-691-01 Interface Unit Connector Attachment IBM AT Computer To BUS CONNECTOR...
SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAMS CN310 CN311 (VIDEO AMP, RGB OUT) DDC SCL DDC SCL DDC SDA DDC SDA TO FBT HC FC IC001 IC002 RGB PRE-AMP RGB OUT CN313 CN315 CN316 BLUE1 B IN B OUT B. IN B.
Page 23
µ-COM, CY, DEFLECTION , POWER, H DEF, HV CN603 D625 AC IN LF602 CN600 F601 T602 AC RECT :LFT :SRT AC L 200V TH600 IC604 IC603 SW REG CONT AC H 12V REG RY602 S602 IC701 CY AMP TH601 RY601 V IN CN610 IC610...
VIDEO AMP RGB OUT 5-4. SCHEMATIC DIAGRAMS AND PRINTED — A BOARD — WIRING BOARDS Note: Part Replaced ([) • All capacitors are in µF unless otherwise noted. (pF: µµF) HV ADJ RV901 Capacitors without voltage indication are all 50 V. •...
(2) Schematic Diagrams of D (a, b, c) Board TO A BOARD TO A BOARD TO H BOARD TO A BOARD CN311 CN306 CN2001 TO ECS CN309 3 - 8 PIN CN701 CN1002 CN1003 CN1004 CN1001 :S-MICRO :S-MICRO :S-MICRO JR603 R1016 :CHIP STBY...
Page 30
µ-COM, CY, DEFLECTION, POWER, H DEF, HV — D BOARD — NOTE: The circuit indicated as left contains high voltage of over 600 Vp-p. Care must be paid to prevent an electric shock in inspection or repairing. 5-17 5-18...
USER CONTROL (3) Schematic Diagrams of N, H Boards — N BOARD (Conductor Side) — — N BOARD (Component Side) — V.FBP HSYNCO R829 R830 PLL LOCK R831 R866 :CHIP :CHIP :CHIP FB809 :CHIP C827 CN801 6.3V Q805 H FBP 2SA1037K R817 H SHAPE...
19T2 SECTION 6 EXPLODED VIEWS • Items with no part number and no • Items marked " * " are not stocked since The components identified ! marked are description are not stocked because they they are seldom required for routine critical for safety.
19T2 6-2. PICTURE TUBE 7-685-881-09 +BVTT 4X8 The components identified ! marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK X-4200-620-1 BEZEL ASSY 52-56 * 4-070-217-01 CUSHION...
19T2 6-3. PACKING MATERIALS 105 106 The components identified ! marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK * 4-205-637-01 CARTON INDIVIDUAL * 4-073-278-01 CUSHION ASSY, UPPER...
19T2 19T2 ¡ The components identified marked are SECTION 7 critical for safety. Replace only with the part number specified. ELECTRICAL PARTS LIST The components identified by [ in this REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK NOTE: •...
Page 38
19T2 ¡ The components identified marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C323 1-136-189-00 MYLAR 0.1uF 250V FB010 1-414-231-22 INDUCTOR CHIP C330 1-164-489-11 CERAMIC CHIP 0.22uF...
Page 39
19T2 ¡ The components identified marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK JR021 1-216-296-91 SHORT R045 1-216-057-00 RES-CHIP 2.2K 1/10W JR022 1-216-296-91 SHORT R047 1-216-073-00 RES-CHIP...
Page 40
19T2 ¡ The components identified marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R307 1-216-675-91 METAL CHIP 0.5% 1/10W C504 1-137-368-11 MYLAR 0.0047uF 5% R308 1-216-049-91 RES-CHIP...
Page 41
19T2 ¡ The components identified marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C564 1-115-339-11 CERAMIC CHIP 0.1uF C708 1-126-942-61 ELECT 1000uF C565 1-163-259-91 CERAMIC CHIP 220pF...
Page 42
19T2 ¡ The components identified marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C1030 1-164-222-11 CERAMIC CHIP 0.22uF D611 8-719-053-19 DIODE UF4007G23 C1031 1-164-004-11 CERAMIC CHIP 0.1uF...
Page 43
19T2 ¡ The components identified marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK JR020 1-216-296-91 SHORT D1022 8-719-062-51 DIODE 1PS226-115 D1024 8-719-073-01 DIODE MA111-(K8).S0 JR021 1-216-296-91 SHORT D1025 8-719-158-15 ZENER DIODE RD5.6SB...
Page 44
19T2 ¡ The components identified marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK Q502 8-729-901-87 TRANSISTOR 2SC2411K-CQ R509 1-249-381-11 CARBON 1/4WF Q503 8-729-026-50 TRANSISTOR 2SA1037AK-T146-QR R510...
Page 45
19T2 ¡ The components identified marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R574 1-249-404-00 CARBON 1/4W R679 1-215-467-00 METAL 1/4W R575 1-216-659-11 METAL CHIP 2.2K 0.5%...
Page 46
The components identified by [ in this 19T2 ¡ The components identified marked are manual have been carefully factory- selected for each set in order to satisfy critical for safety. regulations regarding X-ray radiation. Replace only with the part number specified.
Page 47
19T2 ¡ The components identified marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK T502 1-411-594-11 INDUCTOR R2004 1-215-411-00 METAL 1/4W T503 1-435-140-11 TRANSFORMER, FERRITE (LCT) R2005...
Page 48
19T2 ¡ The components identified marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C840 1-163-017-00 CERAMIC CHIP 0.0047uF 10% R820 1-216-049-91 RES-CHIP 1/10W C841 1-163-023-00 CERAMIC CHIP 0.015uF...