Page 1
OPERATION AND PARTS MANUAL MODEL MT-75H TAMPING RAMMER (EC-12G ROBIN ENGINE) Revision #8 (04/02/07) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
TABLE OF CONTENTS Proposition 65 Warning ......... 2 EC-12G ROBIN ENGINE Table Of Contents ..........4 Crankcase and Cylinder Head .......26-27 Parts Ordering Procedures ........5 Crankshaft and Piston........28-29 Rules For Safe Operation ........6-7 Muffler and Air Cleaner ........30-31 Operation and Safety Decals ........ 8 Governor ............32-33 General Information ..........
Choose from three easy options: Order via Internet (Dealers Only) Best Deal! If you have an MQ Account, to obtain a Order parts on-line using Multiquip’s SmartEquip website! Username and Password, E-mail us at: ■ View Parts Diagrams parts@multiquip.com. ■ Order Parts To obtain an MQ Account, contact your ■...
■ NEVER use accessories or attachments, which are not ■ NEVER operate the rammer in an explosive atmosphere or recommended by Multiquip for this equipment. Damage to near combustible materials. An explosion or fire could result the equipment and/or injury to user may result.
Page 7
■ NEVER use accessories or attachments, which are not ■ Always know the location of the nearest fire extinguisher recommended by Multiquip for this equipment. Damage to and first aid kit . Know the location of the nearest telephone. the equipment and/or injury to user may result.
To maintain optimum performance, proper operation and service are essential. Construction of Tamping Rammer The Mikasa MT-75H is equipped with an air cooled, two cycle gasoline engine. Transmission of the power takes place by increasing the engine speed to engage the centrifugal clutch.
16. Spark Plug – Provides spark to the ignition system, excess fuel is present in the carburetor, or crankcase. L1. A Returned Material Authorization must be approved by Multiquip prior to shipment. A copy of the Authorization must replace with engine manufactures recommended type accompany the shipment to the designated Warehouse.
Page 12
MT-75H — OPERATION Inspection This section is intended to assist the operator with the initial start-up of the MT-75H Tamping Rammer. It extremely important 1. Check all nuts, bolts fasteners for tightness. Retighten as that this section be read carefully before attempting to operate necessary.
MT-75H — OPERATION 2. Close the choke lever Figure 3 and move the throttle lever to the "Full Open" position. Turning the choke lever 90 degrees clockwise closes the choke . In cold weather, start the unit with choke fully closed. In warm weather or when the engine is warm, the unit can be started with choke halfway or completely open.
MT-75H — MAINTENANCE ■ The air cleaner on the engine side will hardly be Maintenance contaminated, if it is, however after cleaning the element Perform the scheduled maintenance procedures as indicated: with kerosene, dip it in mixed oil consisting of 3 parts of DAILY gasoline and 1 part of engine oil.
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
MT-75H — NAME PLATES AND DECALS NAME PLATE AND DECALS PART NO PART NAME QTY. REMARKS 920202930 DECAL: START SWITCH NPA-293 920200900 DECAL: 3750 ~ 3950 RPM NPA-90 920106460 DECAL: MIKASA 920203980 DECAL ELEMENT SET NPA-398 0732004430 DECAL: START SWITCH 920203290 DECAL: CAUTION NPA-329...
MT-75H — GUIDE CYLINDER AND FOOT GUIDE CYLINDER AND FOOT PAGE 22 — MT-75H — PARTS & OPERATION MANUAL — REV. #8 (04/02/07)
Page 23
MT-75H — GUIDE CYLINDER AND FOOT ASSY. GUIDE CYLINDER AND FOOT PART NO PART NAME REMARKS FOOT ASSY..........1 ..INCLUDES ITEMS W/ CONTACT UNIT SALES ACCESSORY ITEM. REPLACES 352910033 352423290 PISTON PIN 080100150 STOP RING 355334300 PISTON ROD 355447240 PISTON END 020316130 NUT M16...
MT-75H — TANK AND HANDLE ASSY. TANK AND HANDLE PAGE 24 — MT-75H — PARTS & OPERATION MANUAL — REV. #8 (04/02/07)
Page 25
MT-75H — TANK AND HANDLE ASSY. TANK AND HANDLE PART NO PART NAME REMARKS 353910010 FUEL TANK AY (P) ........1 ..INCLUDES ITEMS W/ 354111831 HANDLE 351319900 SHOCK ABSORBER 014210020 SOCKET HEAD BOLT 10X20 T .....4 ..REPLACES 001521020 033121009 TOOTHED LOCK WASHER M10 012210020 BOLT 10X20 H, SW ........4 ..REPLACES 002211020 351110650...
EC-12G ENGINE (ROBIN) — CRANKSHAFT AND PISTON ASSY. CRANKSHAFT AND PISTON PART NO PART NAME REMARKS 1612040100 CRANKSHAFT AY 1612340101 PISTON COMPL. STD 1612340201 PISTON COMPL. 0.25 OS 1612340301 PISTON COMPL. 0.5 OS 1612350107 PISTON RING SET STD. 1612350207 PISTON RING SET 0.25 OS 1612350307 PISTON RING SET 0.5 OS 1572330103...
EC-12G ENGINE (ROBIN) — MUFFLER AND AIR CLEANER MUFFLER AND AIR CLEANER PAGE 30 — MT-75H — PARTS & OPERATION MANUAL — REV. #8 (04/02/07)
Page 31
EC-12G ENGINE (ROBIN) — MUFFLER AND AIR CLEANER MUFFLER AND AIR CLEANER PART NO PART NAME REMARKS 1613010111 MUFFLER COMPL. 1613500101 MUFFLER BRACKET 1613510101 MUFFLER BRACKET 1613520101 GASKET COMPL. (EXHAUST) 020108060 NUT ............2 ..REPLACES 0021908000 030208200 SPRING WASHER ........2 ..REPLACES 0032008000 0011308160 BOLT AND WASHER ASSY.
TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS Parts must be in new and resalable con- Multiquip reserves the right to quote and sell dition, in the original Multiquip package (if direct to Government agencies, and to Original Terms of payment for parts are net 30 days.