MULTIQUIP Mikasa Series Operation Manual
Tamping rammer
Hide thumbs
Also See for Mikasa Series:
- Operation and parts manual (116 pages) ,
- Operation manual (90 pages) ,
- Manual (64 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MULTIQUIP Mikasa Series
Summary of Contents for MULTIQUIP Mikasa Series
- Page 1 OPERATION MANUAL SERIES MODEL MTR40F TAMPING RAMMER (ROBIN EH090D/EH092D GASOLINE ENGINES) Revision #4 (10/01/20) To find the latest revision of this publication or associated parts manual, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
-
Page 2: Proposition 65 Warning
PROPOSITION 65 WARNING PAGE 2 — MTR40F RAMMER — OPERATION MANUAL — REV. #4 (10/01/20) -
Page 3: Table Of Contents
TABLE OF CONTENTS MTR40F Tamping Rammer Proposition 65 Warning ..........2 Table Of Contents .............3 Safety Information ..........4-7 Specifications ............8 General Information ..........9 Components............10 Basic Engine ............11 Operation ............12-15 Maintenance ............. 16-18 Troubleshooting ..........20-21 NOTICE Specification and part number are subject to change without notice MTR40F RAMMER —... -
Page 4: Safety Information
SAFETY INFORMATION Do not operate or service the equipment before reading Potential hazards associated with the operation of this the entire manual. Safety precautions should be followed equipment will be referenced with hazard symbols which at all times when operating this equipment. may appear throughout this manual in conjunction with Failure to read and understand the safety safety messages. - Page 5 NEVER lubricate components or attempt service on a NEVER use accessories or attachments that are not running machine. recommended by Multiquip for this equipment. Damage NOTICE to the equipment and/or injury to user may result. ALWAYS keep the machine in proper running condition.
- Page 6 SAFETY INFORMATION ENGINE SAFETY FUEL SAFETY DANGER DANGER The engine fuel exhaust gases contain poisonous carbon DO NOT add fuel to equipment if it is placed inside truck monoxide. This gas is colorless and odorless, and can bed with plastic liner. Possibility exists of explosion or cause death if inhaled.
- Page 7 SAFETY INFORMATION TRANSPORTING SAFETY CAUTION NEVER allow any person or animal to stand underneath the equipment while lifting. NOTICE Before lifting, make sure that the equipment parts (hook and vibration insulator) are not damaged and screws are not loose or missing. Always make sure crane or lifting device has been properly secured to the lifting bail (hook) of the equipment.
-
Page 8: Specifications
SPECIFICATIONS . S . r t e ) c i l l a . n i l l a . n i l l a . n i e z i . n i t f . ) r h l b / t u l c i t... -
Page 9: General Information
GENERAL INFORMATION Definition of Tamping Rammer CAUTION The Mikasa MTR40F Tamping Rammer is a powerful compacting tool capable of applying a tremendous force in consecutive Before starting operation check the lifting impacts to a soil surface. Its applications include soil compacting handle to: for backfilling for gas pipelines, water pipelines and cable installation work. -
Page 10: Components
COMPONENTS Figure 1. MTR40F Rammer Figure 1 shows the location of the controls and components 8. Fuel Tank/Cap — Remove this cap to add unleaded for the MTR40F Tamping Rammer. The functions of each gasoline to the fuel tank. Make sure cap is tightened securely. control is described below: DO NOT over fill. -
Page 11: Basic Engine
BASIC ENGINE Figure 2. Engine Controls and Components INITIAL SERVICING The engine (Figure 2) must be checked for proper lubrication and Recoil Starter (pull rope) — Manual-starting method. Pull the starter grip until resistance is felt, then pull briskly and filled with fuel prior to operation. - Page 12 INSPECTION This section is intended to assist the operator with the inspection Fuel of the MTR40F Tamping Ramme r. It is extremely important that 1. This rammer is equipped with a two-cycled gasoline engine. this section be read carefully before attempting to operate the Use only unleaded gasoline.
- Page 13 INSPECTION Figure 6. Engine Oil Dipstick (Oil Level) r o t l i o i h ( s a l n i r ° 0 ° 5 r e t ° 0 ° 5 ° 5 Inspection 1 . Check all nuts, bolts fasteners for tightness. Retighten as necessary.
-
Page 14: Operation
OPERATION 4. In cold weather, start the unit with choke lever "Fully Closed" Operation (Figure 10). In warm weather or when the engine is warm, The following steps outline the procedure for starting the engine: the unit can be started with choke halfway or completely Open the fuel shut- off valve by moving the fuel cock open. - Page 15 OPERATION Operation 2. After the engine cools , turn the engine ON/OFF switch to the “OFF” position (Figure 14). 1. To start the rammer tamping action, move the throttle lever (Figure 12) quickly from IDLE (close) to the FULL OPEN position.
-
Page 16: Maintenance
MAINTENANCE Maintenance BREATHER ELEMENT Perform the scheduled maintenance procedures as defined by Table 4 and below: PAPER ELEMENT Daily GRAY OUTER FOAM ELEMENT ■ Thoroughly remove dirt and oil from the engine compartment and rammer. Clean or replace the air cleaner elements as necessary. - Page 17 MAINTENANCE Spark Plug Crankcase Lubrication ■ Remove and clean the spark plug (Figure 20), then adjust ■ The rammer crankcase bearings (Figure 19) should be lubricated with five shots of grease with a hand grease gun the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm). This unit has electronic ignition, which requires no adjustments.
- Page 18 MAINTENANCE Perform the scheduled engine maintenance procedures as defined by Table 4 below: t n i ) 3 ( l i O r i A ) 1 ( g i t l l A & s t l i l o s n i r e t l i F...
- Page 19 NOTES MTR40F RAMMER — OPERATION MANUAL — REV. #4 (10/01/20) — PAGE 19...
-
Page 20: Troubleshooting
TROUBLESHOOTING c i f t l u i t i n i r b i t i n i s o o i t i c a l o i t i l i a l i w . e t l i a t r o r i c... - Page 21 TROUBLESHOOTING ENGINE ENGINE ENGINE ENGINE ENGINE n i t i t a f s i s u j e r r v e l . r e i r p v i t c a l o i t i o i t u l f l f l...
- Page 22 © COPYRIGHT 2020, MULTIQUIP INC. Multiquip Inc , the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.