[Ac Voltage Monitor] - Panasonic PT-RZ21К Operating Instructions Manual

[DETAILED INFORMATION]
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is
green.
*2 This is displayed only when the standard DC motor unit installed in the Zoom Lens (Model No.: ET-D75LE6, ET-D75LE8, ET-D75LE10,
ET-D75LE20, ET-D75LE30, ET-D75LE40, etc.) is replaced with the stepping motor unit using the Stepping Motor Kit (Model No.:
ET-D75MKS10), or when a projection lens with the stepping motor is attached.
*3 [CONSOLIDATED RUNTIME] can be obtained with the following calculation formula. Values obtained by the calculation formula contain a
slight error.
A x 1.0 + B x 0.8
f A: Runtime of the light source with [OPERATING MODE] set to [NORMAL], [USER1], [USER2], or [USER3]
f B: Runtime of the light source with [OPERATING MODE] set to [ECO]
Note
f The content of the status can be sent to the E-mail address (up to two addresses) set in "[E-mail set up] page" (x page 207) when the
<ENTER> button is pressed while displaying the pages 1/6 to 5/6 of the [STATUS] screen.
f The detailed information of the input signal is displayed when the <ENTER> button is pressed while displaying the page 6/6 of the
[STATUS] screen. Information for multiple input signals may be displayed depending on the projected image. Press qw to switch pages.
f There are items that are displayed or not displayed in [SIGNAL INFORMATION] and [DETAILED INFORMATION] depending on the setting
or the input signal.
f If any abnormality has occurred on the projector, press the <DEFAULT> button while the [STATUS] screen is displayed to display the detail
screen of the error information.
f For details on the contents displayed in [SELF TEST], refer to "Self-diagnosis display" (x page 223).

[AC VOLTAGE MONITOR]

Enable or disable the AC voltage monitor function. The value of input supply voltage is displayed on the self-
diagnosis display at the side of the projector when enabled.
1) Press as to select [AC VOLTAGE MONITOR].
2) Press qw to switch the item.
f The items will switch each time you press the button.
[OFF]
[ON]
Note
f When [ON] is set, the value of the input supply voltage is always displayed in the self-diagnosis display while the main power of the projector
is turned on.
f Even when [OFF] is set, the value of input supply voltage can be displayed temporarily in the self-diagnosis display by operating the button
on the remote control. (x page 83)
f The value of input supply voltage cannot be displayed in the self-diagnosis display during standby when the [PROJECTOR SETUP] menu
→ [STANDBY MODE] (x page 165) is set to [ECO].
Chapter 4 Settings — [PROJECTOR SETUP] menu
[INPUT]
[SIGNAL FORMAT]
[SIGNAL FREQUENCY]
[SCAN TYPE]
[TOTAL DOTS]
[DISPLAY DOTS]
[TOTAL LINES]
[DISPLAY LINES]
[COLOR FORMAT]
[SAMPLING]
[BIT DEPTH]
[SIGNAL LEVEL]
[HDCP STATUS]
Conversion formula for [CONSOLIDATED RUNTIME]
Disables the AC voltage monitor function.
Enables the AC voltage monitor function.
Displays the input terminal used for the projected image.
Displays the format of the input signal.
Displays the frequency of the input signal.
Displays the scan type of the input signal.
Displays the total dot count of the input signal.
Displays the number of input signal display dots.
Displays the total line count of the input signal.
Displays the number of input signal display lines.
Displays the color format of the input signal.
Displays the sampling information of the input signal.
Displays the gradation of the input signal.
Displays the signal level of the input signal.
Displays the HDCP status of the input signal. The content of display
is as follows.
[PROTECTED]: When protected with HDCP
[NONE]: When not protected with HDCP
[―]: When there is no signal
ENGLISH - 175