Sony DR-CX530E Service Manual page 33

2-1-9. LCD SECTION
(Non Projector Model)
Refer to page 2-8 about Projector Model.
402
(Note 2)
403
(Claws)
(Claws)
401
#11
#2
413
412
Ref. No. Part No. Description
401 4-476-670-01 COVER (C (453)), HINGE (BLACK)
401 4-476-670-11 COVER (C (453)), HINGE (BROWN)
401 4-476-670-21 COVER (C (453)), HINGE (WHITE)
401 4-476-670-31 COVER (C (453)), HINGE (PINK)
402 1-889-186-11 FP-2192 FLEXIBLE BOARD (Note 2)
403 X-2585-819-1 HINGE (Y (409)) ASSY, T TYPE
404 1-471-573-11 MAGNET (Note 3)
405 4-476-559-01 COVER (M (453)), HINGE
406 4-476-555-01 CABINET (M (453)), P
407 4-476-557-01 PLATE (453), PANEL GROUND
408 4-476-549-01 CUSHION (4531), LCD
409 4-476-558-01 RETAINER (453), LCD
410 4-484-284-01 INSULATING SHEET (453), PD
HDR-CX530E/CX535/CX610E/PJ530E/PJ540/PJ540E/PJ610E_L2
405
#288 (Note 1)
#2
404
(Note 3)
LCD901
408
410 409
411
Ref. No. Part No. Description
411 A-2011-100-A PD-1030 BOARD, COMPLETE (SERVICE)
412 4-476-666-11 CABINET (C (453)), P (CX535: BROWN)
412 4-476-666-21 CABINET (C (453)), P (CX535: WHITE)
412 4-476-666-31 CABINET (C (453)), P (CX535: PINK)
412 4-476-666-41 CABINET (C (453)), P (CX610E)
412 4-476-666-51 CABINET (C (453)), P (CX535: BLACK)
412 4-476-666-61 CABINET (C (453)), P (CX530E)
413 4-274-987-01 TAPE (AS 1/2) (C)
LCD901 A-1992-237-A TP-LCD BLOCK ASSY (SZ814D)
#2 2-635-562-31 SCREW (M1.7)
#11 3-078-890-11 SCREW, TAPPING
#288 2-187-345-21 SCREW (M1.7), P2 (Note 1)
Screw
#2: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping)
(Black) (Silver)
2-635-562-31 3-078-890-11
1.7
4.0
Note
Note 1: This screw cannot be reused. Discard the screw removed
406
once in servicing.
Instead, use a new screw.
Note 2: Refer to "Assembly-1: The Method of attachment of FP-
2192/2193 Flexible Board".
Note 3: Install the magnet with
the marking oriented
as shown below.
407
Marking
2-11
#288: M1.7 X 2.5
(Black)
2-187-345-21
1.7 1.7
2.5
4.0
Note 1: このねじは再利用することができません。
サービス対応時に一度でも外した場合は新品のねじと交換
してください。
Note 2: "Assembly-1: The Method of attachment of FP-2192/2193
Flexible Board" を参照してください。
Note 3: マグネッ トを取付ける
際は， マ−キング面を
図の位置にあわせて
ください。
マーキング