Universal Serial Bus Ports; Headphone Jack; Microphone Jack; Mini-Vga Port - Fujitsu Lifebook P5010 User Manual

L i f e B o o k P 5 0 0 0 N o t e b o o k – S e c t i o n F o u r
When S-Video is connected, you can toggle the S-Video
device on and off by pressing the [F11] key while
holding down the [Fn] key.

UNIVERSAL SERIAL BUS PORTS

The Universal Serial Bus 2.0 ports allow you to connect
USB devices such as external game pads, pointing
devices, keyboards and/or speakers. USB 2.0 is much
faster than USB 1.1 (Its 480Mbps transfer rate is 40
times faster than that of USB 1.1). USB 2.0 ports are
backward-compatible to work with USB 1.1 devices.
In order to connect a USB device follow these easy steps:
(See figure 2-7 on page 9 for port location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.

HEADPHONE JACK

The headphone jack allows you to connect headphones
or powered external speakers to your notebook. Your
headphones or speakers must be equipped with a 1/8"
(3.5 mm) stereo mini-plug. In order to connect head-
phones or speakers follow these easy steps: (See figure 2-7
on page 9 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
P O I N T
If you plug headphones into the headphone jack, the
built-in stereo speakers will be disabled.

MICROPHONE JACK

The microphone jack allows you to connect an external
mono microphone. Your microphone must be equipped
with a 1/8"(3.5 mm) mono mini-plug in order to fit into
the microphone jack of your notebook. In order to
connect a microphone follow these easy steps: (See
figure 2-5 on page 6 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.

MINI-VGA PORT

The mini-VGA port allows you to connect an external
monitor. In order to connect an external monitor follow
these easy steps:
1. Take the mini-VGA cable out of the accessory
package that came with your system.
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
(Figure 2-25)
46
Figure 2-25 Installing the Mini-VGA Cable
P O I N T
Pressing the [Fn] + [F10] keys allows you to change
your selection of where to send your display video. Each
time you press the key combination, you will
step to the next choice, starting with the built-in display
panel only, moving to the external monitor only, finally
moving to both the built-in display panel and an
external monitor.

OPTICAL DIGITAL AUDIO CONNECTOR

The optical digital audio-out connector allows you to
download digital audio to MiniDisc recorders. It uses
SPDIF (Sony Philips Digital Interface) format. Use the
following setting when using the digital audio-out
connector. (See figure 2-7 on page 9 for location)
P O I N T S
When headphones or a SPDIF cable is installed, the
speakers are disabled.
Before using the SPDIF function, make sure that
WinDVD software is installed on your system.
Certain older CDs and DVDs will not work in conjunc-
tion with the SPDIF connector.
1. Connect the MiniDisc recorder or external speaker
to the Optical Digital Audio-Out Connector.
2. Insert the disk you want to play in the DVD/CD-RW
tray.
3. Click on Start --> Programs --> InterVideo
WinDVD. (In Windows XP systems, you can go
directly from Start to InterVideo WinDVD.)
4. When the WinDVD interface appears, click on the
Properties icon in the bottom of the display (it looks
like a wrench).
5. Click on the Audio tab and select Enable S/PDIF
output.
6. Click [Apply].