Related Manuals for Orion F9S936
Summary of Contents for Orion F9S936
- Page 1 19” DIGITAL COLOR MONITOR USER’S MANUAL MODEL No.: F9S936 BEFORE USING THIS COLOR MONITOR, READ AND OBSERVE ALL OF THIS USER’S MANUAL...
-
Page 2: Table Of Contents
CONTENTS SAFETY INSTRUCTION CAUTIONS FCC RF INTERFERENCE STATEMENT INSTALLATION RESOLUTION CONTROLS AND FUNCTIONS REAR VIEW POWER MANAGEMENT SPECIFICATIONS TROUBLE SHOOTING GUIDE This Monitor was Manufactured by ISO 9001 Certified Factory INSTRUCTION MANUAL... -
Page 3: Safety Instruction
SAFETY INSTRUCTION 1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning. 5. - Page 4 SAFETY INSTRUCTION 13. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to service personnel. 14. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions.
-
Page 5: Cautions
CAUTIONS NEVER REMOVE THE BACK COVER NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel. This display monitor contains high voltage inside. DO NOT USE IN HOSTILE ENVIRONMENTS DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard. -
Page 6: Fcc Rf Interference Statement
FCC RF INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 7: Installation
INSTALLATION NO TOOLS ARE REQUIRED TO INSTALL THE MONITOR. SIMPLY FOLLOW THE INSTRUCTIONS OUTLINED IN THE NEXT FEW PAGES. 1. CONNECT THE SIGNAL CABLE A. ATTACHED SIGNAL CABLE 1) If the signal cable is attached on the monitor, connect the other and into the graphic card on back of the computer. -
Page 8: Resolution
RESOLUTION This monitor is a digitally-controlled multi-frequency monitor. It operates at horizontal frequencies of 30 to 96KHz and vertical frequencies of 50 to 160Hz. Because of its micro processor-based designs it offers auto-synchronization and auto-sizing capabilities. This monitor offers 12 programmed settings as listed in the table below. -
Page 9: Controls And Functions
CONTROLS AND FUNCTIONS B.MENU BUTTON POWER INDICATOR(LED) A. POWER SWITCH C.SELECT BUTTON D. ADJUST BUTTONS (DOWN & UP) A. POWER ON/OFF( Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED(next to the power switch) lights when the power is turned ON. - Page 10 CONTROLS AND FUNCTIONS USER MENU 1 activates when you press the Menu button. USER MENU 1 activates when you press the Menu button. USER MENU 2 activates via the adjust ( ) button. USER MENU 2 activates via the adjust ( ) button.
- Page 11 CONTROLS AND FUNCTIONS 2. AUTO REGISTRATION This monitor has 12 preset modes. If the current video is one of the preset modes, the monitor keeps storing the custom display settings into the permanent memory. There are also 10 user modes that allow you to save the custom display settings made to any video mode that is not one of the preset modes.
- Page 12 CONTROLS AND FUNCTIONS PIN BALANCE Adjusts the curvature of the left and right sides of the screen image. TILT Adjusts the tilt of image. RECALL Resets the control functions back to the original factory preset values. In order for the Recall function working, the timing must fall under one of the factory preset timing modes.
- Page 13 CONTROLS AND FUNCTIONS MOIRE Adjusts the moire level of the screen. Activate MOIRE icon & keep pressing select button approximately 2 seconds after select “ON”. H. MOIRE ADJUST Reduces the optical effect of horizontal wavy lines on the display image. These effects are usually more noticeable on large gray areas or on black &...
-
Page 14: Rear View
REAR VIEW E. AC INLET Power cord connection. N N O O T T E E S S Power cord is used as main power disconnect device in this product. F. D-SUB CONNECTOR OF SIGNAL CABLE Connect to the analog RGB signal output connector of video card. E. -
Page 15: Power Management
POWER MANAGEMENT This monitor features a power management system to “power down” upon receipt of the VESA DPMS(The display power management signaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal. This monitor enters an appropriate mode through identifying each of the three modes of the signaling system. -
Page 16: Specifications
SPECIFICATIONS 19 (18 Viewable) diagonal measurement ARAS(Anti-Reflection Anti-Static) Coating. 0.26mm Dot Pitch RESOLUTION(H x V) RESOLUTION(H x V) 1600x1200 Non Interlaced FREQUENCY FREQUENCY HORIZONTAL : 30-96KHz VERTICAL : 50-160Hz INPUT SIGNAL INPUT SIGNAL VIDEO(Analog 0.7Vp-p/75 ) SYNC(Separate and Composite TTL Level) ACTIVE DISPLAY AREA (W x H) ACTIVE DISPLAY AREA (W x H) Preset : 346mm X 255mm... -
Page 17: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE TROUBLE TROUBLE SHOOTING TIP No image on display screen 1. Check that power cord of the Monitor have been connected securely into wall outlet or grounded extension cable or strip. 2. Powerf switch should be in the ON position and LED is lit.