Setting Contrast Mode - Cobra 29 LX MAX User Manual

Operation
Note Bluetooth®
Dual Point Bluetooth:
Calls on a Bluetooth® enabled cell phone can be routed
For team drivers, two cell phones
through the 29 LX MAX speaker or external speaker
can be paired, however; only one
accessory.
NB/ANL
phone can be used at a time.
MAX
2 3
1.5
NB/ANL CAL
SWR
ANL
S/ RF
S/RF
RF
SWR
CAL
3 5 7 9
1
SIG +30dB
SWR/CAL
Note
VOL SQ DYNAMIKE
If no further pairing steps are
taken, the unit will time-out
and return to Standby after 90
seconds. During the pairing
OFF MIN MAX
process, press and release the
BT Button or DIM/ESC to
cancel the pairing process.
Note
For Text-to-Speech conversion,
an app should be downloaded
to your cell phone.
AW-1210039-1B_29LX_MAX_MANL_REV_022021.indd 22-23 AW-1210039-1B_29LX_MAX_MANL_REV_022021.indd 22-23

Setting Contrast Mode

Press the Menu/Enter knob and rotate clockwise to select
Set Contrast.
NW LIGHTING
CONTRAST
RADIO CHECK
Rotate the Menu/Enter knob clockwise to increase
contrast, counter-clockwise to decrease contrast.
Press the Menu/Enter knob to save and exit and continue
settings or DIM/ESC to exit Menu mode.
SET CONTRAST
------
SAVE AND EXIT
READY FOR
TX
PAIRING
RX
PW 0000
MEM WX !
BT Button
RF GAIN
To Pair with a Cell Phone
Press and hold the BT Button for six seconds to enter
Ready For Pairing mode. A tone will sound to confirm
MIN MAX
entry to pairing mode.
A. First time pairing with a cell phone:
I. A tone will sound to confirm Pairing mode.
II. Follow the cell phone manufacturer's instruction to
enable its Bluetooth function. Select 29 LX MAX from
the list of Bluetooth devices. Enter the PIN (Personal
Identification Number) 0000 if required.
Most smartphones no longer require a PIN entry.
22
III. Successful pairing will be indicated by
a tone to confirm entry to Connected
mode. A pair record will also be established for
subsequent connections.
B. Subsequent pairings with a cell phone:
I. Follow the cell phone manufacturer's instruction,
to enable it's Bluetooth® function.
II. Successful pairing will be indicated by a tone to
confirm entry to Connected mode.
To Answer Calls
Press and release the BT Button when the cell phone ring is
1
heard through the 29 LX MAX speaker.
Speak into the 29 LX MAX microphone. The CB function
2
of the unit and PTT Button will be disabled while a call
is in progress.
Press and release the BT Button to end the call.
3
A tone will sound.
CH 9/
SCAN
19
To Initiate Calls
MEM SCAN
To initiate the phone's voice assistant, if supported,
1
press and release the BT Button twice.
ESC
Dial a number according to the cell phone manufacturer's
2
instructions. The key press and other tones will be heard
through the 29 LX MAX speaker.
SWR
DELTA TUNE T BACK
CAL
Press Send on the cell phone, you will hear the ring
3
tone for the number you dialed on the CB speaker.
Once connected, speak into the microphone.
Press and release of the BT Button to end the call.
4
OFF
A tone will sound.
Press and hold the BT Button for two seconds to redial
5
a number. A tone will sound; and after a few seconds,
you will hear the ring tone for the number you dialed.
Operation
Note
When cell phone calls are in
progress using the Bluetooth
features, the CB functions of
the unit are disabled unless the
phone call is put on hold (see
page 27).
Note
When dialing a phone number
on your phone's keypad, it is
recommended that you dial
when the vehicle is not in
motion.
Note
The external microphone (see
accessories on page 35) can be
plugged into the rear of the
unit and clipped to a pocket
or lapel for hands-free speech
during calls.
When the external microphone
is plugged in, the main
microphone will not pick up
speech during calls but will be
fully functional for CB operation.
23
2/24/21 2:55 PM 2/24/21 2:55 PM