Nb-Anl/Off (Noise Blanker/Automatic Noise Limiter Switch); Program Memory Channels - Cobra 29 LX MAX User Manual

Operation
NB-ANL/OFF (Noise Blanker/Automatic
Noise Limiter) Button
Note
The RF noise blanker is very
effective in reducing repetitive
noises such as ignition
interference.
When switched to ANL mode the Automatic Noise
Limiter is activated. This helps reduce noise created by
the vehicle's electronics.
When switched to NB/ANL mode the RF Noise Blanker is
also activated, providing increased noise filtration.
When switched to Off, all noise filtration will be turned off.
Setting Delta Tune
Rotate the Delta Tune knob to the center position for
optimum tuning.
2 3
NB/ANL 1.5
SWR CAL
RF Gain Control
ANL
S/RF
RF
The RF Gain is used to optimize reception in strong or
SWR
CAL
3 5 7 9
1 weak signal areas.
SIG +30dB
SQ
VOL DYNAMIKE
OFF MIN MAX
Rotate the RF Gain knob counterclockwise to reduce gain
in strong signal areas. In weak signal areas turn clockwise
to increase gain.
32
AW-1210039-1B_29LX_MAX_MANL_REV_022021.indd 32-33 AW-1210039-1B_29LX_MAX_MANL_REV_022021.indd 32-33
2 3
1.5
NB/ANL SWR CAL
TX
ANL
RX
S/RF
RF
3 5 7 9
1
SIG +30dB
SQ DYNAMIKE
VOL
2
1.5
NB/ANL
SWR
ANL
S/RF
RF
OFF MIN MAX
SWR
CAL
3
1
SIG
VOL SQ DYNAMIKE
OFF MIN
1.5 2
NB/ANL
SWR
ANL
S/RF
RF
SWR
CAL
3
1
SIG
TX
RX
SQ DYNAMIKE
VOL
MEM WX !
RF GAIN DELTA TUNE T BACK
OFF MIN
1.5
NB/ANL
SWR
ANL
S/RF
MIN MAX RF
SWR
CAL
1
SIG
VOL SQ DYNAMIKE
OFF MIN

Program Memory Channels

Set first channel. Press and hold the SCAN/MEM-SCAN
button. The Memory icon will appear. Select a second
channel, press and hold the SCAN/MEM-SCAN button
SCAN CH 9/19
again until the Memory icon appears. Repeat above steps
to enter up to 10 channels in memory.
MEM WX !
SWR
RF GAIN
DELTA TUNE T BACK
CAL
3
CAL
TX
RX
MIN MAX OFF
5 7 9
+30dB
MEM
RF GAIN
MAX
MIN MAX
3
CAL
TX
RX
5 7 9
+30dB
SCAN CH 9/19
MEM
RF GAIN
Pressing the SCAN/MEM-SCAN button toggles from
1
Off to Scan All Channels to Memory Channel Only
SWR Scan and back to Off.
CAL
MAX MIN MAX
2 3
CAL
TX
RX
OFF
5 7 9
3
+30dB
MEM WX !
RF GAIN
Press the DIM/ESC button to end Scan and
2
return to CB mode.
MAX
MAX MIN
Operation
Note
The radio should be
squelched before scan
features are activated.
Note
Keying the microphone will stop
SCAN CH 9/19
the scan feature.
Note
If more than 10 channels are
attempted to be programmed,
SWR
DELTA TUNE T BACK
3 error beeps will be heard and
CAL
"Memory Full" will be displayed
for 10 seconds or until any
button is pushed.
OFF
SCAN CH 9/19
Note
To remove a channel from
memory, go to the unwanted
memory channel then press and
hold the SCAN/MEM SCAN
SWR
DELTA TUNE T BACK
CAL
button until the MEM icon
turns off.
OFF
SCAN CH 9/19
SWR
DELTA TUNE T BACK
CAL
OFF
33
2/24/21 2:55 PM 2/24/21 2:55 PM