Related Manuals for Clarke air CAT34B
Summary of Contents for Clarke air CAT34B
- Page 1 ORBITAL SANDER MODEL No: CAT34B Part Nos: 3110434 OPERATING & MAINTENANCE INSTRUCTIONS GC07/13...
-
Page 2: Introduction
GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. -
Page 3: Table Of Contents
" 4 Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 4: General Safety Precautions
• Do not carry out any alterations or modifications to the sander. • The sander should be serviced as required by your CLARKE dealer. • Never use the sander if it is defective or operating abnormally. • ALWAYS ensure the workpiece is firmly secured leaving both hands free to control the sander. - Page 5 • ALWAYS ensure that any attachments are correctly fastened before connecting the sander to the power supply. • Always disconnect from the air supply when: performing any maintenance. the sander is not in use. the sander will be left unattended. moving to another work area.
- Page 6 AIR SUPPLY REQUIREMENTS WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE THOROUGHLY FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND COMPRESSED AIR SUPPLY. • Use only clean, dry, regulated compressed air as a power source. •...
-
Page 7: Overview
4. Connect the other end of the hose to the compressor. (A whip hose with a quick fit coupling is available from your CLARKE dealer). 5. Turn on the air supply and check for air leaks. Rectify any found before proceding. -
Page 8: Operating Instructions
2. If the sander is not to be used for longer than 24 hours, run a few drops of CLARKE airline oil into the air inlet and run the tool for a few seconds to ensure that the oil has been well distributed throughout the sander. -
Page 9: Troubleshooting
In the event that any of the above situations occurs, requiring the dismantling and overhaul of the tool, contact your CLARKE International Service Department on 020-8988-7400. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 10: Maintenance
**Clarke Air Line Oil is available from your CLARKE dealer part no. 3050825. ACCESSORIES A wide range of airline accessories are available including filter/regulators, lubricators, high pressure hoses, adaptors and connectors etc. -
Page 11: Parts Lists And Diagrams
PARTS DIAGRAM Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 12 PARTS LIST l f f - - - - - - Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 13: Vibration Emissions
VIBRATION EMISSIONS HAND-ARM VIBRATION Employers are advised to refer to the HSE publication “Guide for Employers”. All hand held power tools vibrate to some extent, and this vibration is transmitted to the operator via the handle, or hand used to steady the tool. Vibration from about 2 to 1500 herz is potentially damaging and is most hazardous in the range from about 5 to 20 herz. - Page 14 You will note that a third value is given in the specification - the highest measured reading in a single plane. This is the maximum level of vibration measured during testing in one of the axes, and this should also be taken into account when making a risk assessment.
-
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...