Table of Contents
Advertisement
MAINTENANCE AND CARE
REFRACTORY REPLACEMENT
The intense heat of the fire will normally cause
hairline cracks in the refractory. These cracks
can be minimized by proper curing as described
in "First Fires". They will not normally dimin-
ish the effectiveness of the refractory. If large
cracks develop, then the refractory should be
replaced. To replace the refractory bricks, fol-
low these steps:
1. Remove the front refractories
2. Remove the bottom refractory
3. Remove the left side refractory
4. Remove the right side refractory
5. Remove the back refractory
6. Remove the front ceramic baffle
7. Remove the rear ceramic baffle
To install the new refractories, follow the above
steps in reverse.
DOOR INSTALLATION
The door must be installed only when the
installation of the fireplace is complete, but
before the facade is installed. All you have to
do is fit the male part of the hinge, already on
the door, to the female part, which is on the
fireplace. To remove the door, simply pull the
door up from the hinges (see Figure 5). The
door adjustment has been set at the factory.
If the fit is still not perfect, you can adjust the
door using the hinge screws.
NOTE: If the door is to be removed after instal-
lation of a facade, the upper pin must be axially
raised from the door hinge with the use of a
mallet and punch. In the door-open position
tap the pin from the underside until it has lifted
approximately 1". This will allow the pin to
disengage from the capture hinge on the unit
when the door is lifted for removal.
DOOR ADJUSTMENT
The door may need to be adjusted to keep the
door gasket completely airtight. The door hinges
may be loosened using a 3/8" Nut driver and
1/8" Allen Key. The door mount hinges may also
be adjusted with a 5/32 Allen Key. Additionally,
on the right side of the unit there is a latch
1/8" Allen
Key
3/8" Nut-Driver
DETAIL A
Figure 5 - Door Installation
8
(continued)
1. Front Refractories
2. Bottom Refractory
3. Left Side Refractory
4. Right Side Refractory
Figure 6
adjustment screw (Figure 5) which may be used
to tighten the door gasket when the door is closed
(5/32" Allen Key).
Checking Door Seal - A one-inch strip of paper
may be used to perform a test of the integrity of
the door seal. Close the door on the paper in at
least eight points. It is normal to feel only a slight
amount of friction. The door gasket does not need
to be "tight" in all areas, since a small amount
of leakage is not hazardous or detrimental to the
performance of your fireplace.
• Use only a IHP glass doors, specifically
designed for this fireplace.
• The fireplace cannot be operated with-
out door. Consult your dealer to select
the correct replacement door.
• Important! To assure proper alignment
of glass doors: Install this fireplace in
a square and plumb condition, using
shims as necessary at sides and/or
bottom.
5/32"
Allen Key
Detail A
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
5
5. Back Refractory
6. Front Ceramic Baffle
7. Rear Ceramic Baffle
WARNING
A
u
Latch Adjustment For Square Doors
v
Latch Adjustment For Arch Doors
7
2
3
COLD CLIMATE INSTALLATIONS
Climates where temperatures will fall below
32° F (0° C).
The heating performance of the appliance
will vary depending upon the level of insula-
tion, house design, how the appliance is
operated, etc.
If this fireplace is being installed in a cold
climate, it is especially important to seal all
cracks around the fireplace and wherever
cold air could enter the room with noncom-
bustible material.
Also, the outside air inlet duct should be
wrapped with noncombustible insulation to
minimize the formation of condensation. Do
not place insulation materials directly against
the chimney sections. We recommend that
you use the insulated wall radiation shield
since it will maintain the home's thermal bar-
rier. AC chimney is NOT recommended in
very cold climates (in areas with temperatures
below 32°F (0°C).
Door Adjustment Screws
(indicated by arrows)
u
u
5/32"
Allen Key
v
u
u
6
4
1
Advertisement
Table of Contents
