Advertisement
1. Determine length of brass NPT nipple (13, 13A)
needed:
a. Place mark on existing shower arm at wall
surface. Unscrew shower arm from elbow in
wall.
b. Measure distance from mark on shower
arm to end of shower arm threads. Add
to this measurement, and then round to
nearest
1
⁄
".
2
Example 1: If measurement = 1
1
3
⁄
", rounded = 2" NPT nipple, this is the
4
length needed.
Example 2: If measurement = 1
2
1
⁄
", rounded = 2" NPT nipple, this is the
8
length needed.
IMPORTANT:
If shower arm is located in wall
above tile/fiberglass wall surface you must
add distance from sheetrock to face of tile/
fiberglass shower wall to above measurement.
NOTE:
If
1
⁄
" X 1
1
⁄
"nipple (13) provided is not
2
2
correct length based on above formula, you
can attach one or both
(13A) to obtain desired length or it may be
necessary to purchase required length
brass nipple (available at most hardware stores
in
1
⁄
" incremental lengths).
2
4. Apply a generous amount of PTFE (plumber's)
tape to both ends of nipple (13, 13A).
IMPORTANT: Do not damage final ½" of nipple
threads protruding from wall.
5. Insert shower arm (2) into body of Aloha
Showerspa (1) and secure with nut (6). Insert
washer (7) into 90° fitting (8) on shower arm
supply line and securely tighten 90° fitting (8)
to shower arm ensuring no leaks. CAUTION: Do
Not Overtighten.
6. If using hole A for mounting continue to Step
10. If using hole B or C of mounting plate (12)
remove mounting plate from Splash.
Installation
1
⁄
"
2
1
⁄
", add
1
⁄
" =
4
2
5
⁄
", add
1
⁄
" =
8
2
3
⁄
" nipple extensions
4
⁄
" NPT
1
2
7. Loosen compression nut (9) and remove
90° fitting (8). Cut supply line (23) at
predetermined mark depending on hole
choice. Important: Supply line must be cut
clean and square to ensure no leaks - take your
time, maybe even practice higher up on hose!
8. Slide compression nut (9) onto supply line (23).
9. Push supply line (23) over barbed portion of
90° fitting (8) until it bottoms against base of
threads.
10. Slide compression nut (9) onto 90° fitting (8)
and securely tighten.
11. Remove face of tape (14) from mounting plate
(12) and slide plate over nipple (13) through
predetermined hole A, B or C. Level plate
before adhering to wall.
12. Push retaining washer (11) over nipple (13)
securing mounting plate (12) to wall and/or
use nut (6).
13. Optional: secure mounting plate using
supplied wall fasteners. Drill 5mm (3/16in.)
wide X 25mm (1in.) deep holes using a
masonry/tile drill bit. CAUTION: live (active)
plumbing is behind wall! Insert mushroom
head anchors (15) through plate and carefully
hammer nail (16) flush to mushroom head
anchor.
14. Insert washer with screen (10) into 90° fitting
(8) and connect to nipple (13). Turn on water
and check for leaks. Once leak free carefully
slide Aloha (1) onto mounting plate (12) and
push down to secure.
15. Insert 6mm washer (3) into showerhead (4)
and attach to Aloha (1).
16. Insert washer (7) into each end of shower hose
(22) and secure hex head to Aloha (1) and cone
shape end to hand shower (21).
3
Advertisement
