Table of Contents
Advertisement
> Before Start
> Part Names
■ 4. Level Calibration
Front Left
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Center
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Front Right
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Height Left
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Height Right
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Surround Right
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Surround Left
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Subwoofer
Select a value between "j15 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
58
> Install
> Initial Setup
> Playback
Supplementary Information |
∫ 5. Dolby Enabled Speaker
Dolby Enabled
Set the distance between the Dolby enabled speaker and the
Speaker to Ceiling
ceiling. Select a value between "0.1 ft/0.03 m" and "15.0 ft/
4.50 m" (in 0.1 ft/0.03 m increments, default value is "1.80 m")
0 The unit of distance (feet/meters) shown is the unit selected
for use in "Distance".
AccuReflex
You can enhance the reflection effect of Dolby enabled speaker
from the ceiling.
"On": When this function is to be used
"Off (default value)": When this function is not to be used
0 The function is not effective if the listening mode is Direct.
0 This setting can only be selected when you have set "Configuration" - "Height Speaker" to
"Dolby Speaker".
■ 6. Equalizer Settings
You can adjust the output volume of the range of each connected speaker. You can adjust
the volume of the different sound ranges for each of the speakers. You can set three
different equalizers in Preset 1 to 3. You can select up to 5 bands for the Subwoofer and 9
bands for all other speakers. To use the set equalizer effects, select the preset number in
"QUICK MENU"- "AccuEQ" - "Equalizer" (
Front
After selecting the speaker frequency from between "25 Hz" and
"16 kHz" with the cursors
frequency between "j6.0 dB" and "i6.0 dB" with
Value is "0.0 dB")
Center
After selecting the speaker frequency from between "25 Hz" and
"16 kHz" with the cursors
frequency between "j6.0 dB" and "i6.0 dB" with
Value is "0.0 dB")
Height
After selecting the speaker frequency from between "25 Hz" and
"16 kHz" with the cursors
frequency between "j6.0 dB" and "i6.0 dB" with
Value is "0.0 dB")
Advanced Setup
P50).
/ , adjust the volume of that
/ . (Default
/ , adjust the volume of that
/ . (Default
/ , adjust the volume of that
/ . (Default
| Others
E
N
Hide quick links:
Advertisement
Table of Contents
