Panasonic KX-TCA151AXM Service Manual page 88

KX-TCD530AXM / KX-TCA151AXM
27.3.3. Flash Time Setting
Address Initial
Type
E 1
F 1
10 1
27.3.4. Clip (Caller ID) configuration
Address Initial
Type
51 1
59 1
5A 1
5B 1
5C 1
5D 1
5E 1
5F 1
60 1
61 1 EEP_AddZeroDataCount
62 1
63 1
Name
FlashTime1
FlashTime2
FlashTime3
Name
EEP_RingDetectfmin
EEP_ClipDetectConfig
EEP_ClipRingConfig
EEP_ImpSetConfig
EEP_ImpRemConfig
EEP_CasAckDtmf
EEP_DtmfReceiveData
Count
EEP_ClipPhaseConfig
EEP_ClipPhaseConfig2
EEP_RingVmwiConfig
EEP_RpasMinDuration
Description
Calibrated loop-break time for short break
Unit : 10 ms, defaults to 700 ms
Calibrated loop-break time for long break
Unit : 10 ms, defaults to 80 ms
Calibrated loop-break time for extra-long break
Unit : 10 ms, defaults to 400 ms
Description
Lower Limit for detection of ring frequency
Unit : 1Hz, Default = 18Hz
CLIP detect configuration
Bit0-2:Mode...0:Learn mode, 1:DTMF only, 2:FSK only,
3:FSK/DTMF both, 4:Russian CLIP only
Bit3:Unused3
Bit4:Onhook...1=enable, 0=disable
Bit5:Offhook...1=enable, 0=disable
Bit6:MsgWaiting...1=enable, 0=disable
Bit7:Unused7
Ring configuration
Bit0:Rpas...1=enable, 0=disable
Bit1:RpasAlert...1=enable, 0=disable
Bit2:Rpas2LongAlert...1=enable, 0=disable
Bit3:Suppress1stRing...1=enable, 0=disable
Bit4-7:Unused
Impedance Set configuration
Bit0:Polarity...1=enable, 0=disable
Bit1:Dtas...1=enable, 0=disable
Bit2:Rpas...1=enable, 0=disable
Bit3:PowerRing...1=enable, 0=disable
Bit4:LearnImpPattern...1=enable, 0=disable
Bit5:CheckPolStatus...1=enable, 0=disable
Bit6-7: Unused
Impedance Remove configuration
Bit0:Polarity...1=enable, 0=disable
Bit1:Ringing...1=enable, 0=disable
Bit2:ClipReceived...1=enable, 0=disable
Bit3:Offhook...1=enable, 0=disable
Bit4:ChszDet...1=enable, 0=disable
Bit5-7:Unused
CAS Acknowledge DTMF tone
00:DTMF 0 - 09:DTMF 9
0A:DTMF A
0B:DTMF B
0C:DTMF C
0D:DTMF D
0E:DTMF *
0F:DTMF #
Valid Receive data Count (for INDIA)
CLIP phase set configuration
Bit0:ForwardNumber...1=enable, 0=disable
Bit1:CallingNumber...1=enable, 0=disable
Bit2:Dutch...1=enable, 0=disable
Bit3:Canadian...1=enable, 0=disable
Bit4:KpnVmwi...1=enable, 0=disable
Bit5:PriorityCheck...1=enable, 0=disable
Bit6-7:AddZero...0:no add zero, 1:add zero absolutely
2:Check Number's top is zero. If it is zero, add zero.
CLIP phase set configuration
Bit0:FskRemoveParity...1=enable, 0=disable
Bit1:AutoRappel...1=enable, 0=disable
Bit2:KpnStartEndNg
Bit3-7:Unused
Valid data for Add Zero (for NewZealand)
CLIP RingVmwi set configuration
Bit0:LongBellFuncOff...1=enable, 0=disable
Bit1:StatusSucceed...1=enable, 0=disable
Bit2-7:Unused
RPAS minimum duration
Unit : 10ms, Default : 180ms
88
Default value Country
Setting
0x46 0x0A
0x08 0x3C
0x28 0x1E
Default value Country
Setting
0x12 0x0E
0x73 x
0x00 x
0x15 x
0x0F x
0x0D x
0x04 x
0x04 x
0x01 x
0x05 x
0x01 x
0x12 x