Advertisement
Available languages
Available languages
OBJ_BUCH-2619-002.book Page 8 Wednesday, June 15, 2016 10:19 AM
8 | English
Cordless angle drill/driver
Weight according to EPTA-
Procedure 01:2014
Permitted ambient temperature
– during charging
*
– during operation
and during
storage
Recommended batteries
Recommended chargers
* Limited performance at temperatures <0 °C
Technical data determined with battery from delivery scope.
Assembly
Battery Charging (see figure A)
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
To remove the battery 10 press the unlocking buttons 9 and
pull out the battery downwards. Do not exert any force.
Observe the notes for disposal.
Changing the Tool (see figure B)
Before any work on the power tool, remove the battery.
Inserting
Pull the locking sleeve 1 toward the front and then push the in-
sert tool to the stop into the tool holder 2. The insert tool is au-
tomatically locked.
Removing
Pull the locking sleeve 1 forward and remove the insert tool.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
1 609 92A 36T | (15.6.16)
– Provide for good ventilation of the working place.
GWI 12 V-LI
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
kg
1.1
materials to be worked.
Prevent dust accumulation at the workplace. Dust can
°C
0...+45
easily ignite.
°C
–20...+50
Operation
GBA 12V...O–..
GAL 12.. CV
Starting Operation
Inserting the battery
Use only original Bosch lithium-ion batteries with the
voltage listed on the nameplate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
Note: Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
Reversing the rotational direction (see figure C)
The rotational direction switch 4 is used to reverse the rota-
tional direction of the machine. However, this is not possible
with the On/Off switch 5 actuated.
Right Rotation: For drilling and driving in screws, push the
rotational direction switch 4 left to the stop.
Left Rotation: For loosening or unscrewing screws, push the
rotational direction switch 4 right to the stop.
Setting the torque
With the torque selector switch 6, you can preselect the re-
quired torque in 8 steps. When the torque setting is adjusted
correctly, the insert tool is stopped as soon as the screw is
driven flush into the material or when the set torque is
reached. In the "
ed; e.g., for drilling.
In left rotation the safety clutch is deactivated.
Switching On and Off
To start the machine, press the On/Off switch 5 and keep it
pressed.
To switch off the machine, release the On/Off switch 5.
To save energy, only switch the power tool on when using it.
Adjusting the Speed
The speed of the switched-on power tool can be variably ad-
justed, depending on how far the On/Off switch 5 is pressed.
Light pressure on the On/Off switch 5 results in a low rotation-
al speed. Further pressure on the switch results in an increase
in speed.
Fully automatic spindle locking (Auto-lock)
When the On/Off switch 5 is not pressed, the drill spindle and
thus the tool holder are locked.
This enables screws to be screwed in, even when the battery
is empty and allows for the machine to be used as a screwdriv-
er.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject
to overload. When the load is too high or the allowable battery
" position, the safety clutch is deactivat-
Bosch Power Tools
Advertisement
