General Engine Maintenance; Belts - HUSTLER SmoothTrak Super S Manual

Kawasaki FX691V engine
CZ
DA
DE
A. Safety filter
EN
gaskets for cuts or tears. Do not attempt to use a
damaged element which will allow abrasive particles
to enter the engine.
3. Reinstall the dust cap. Make sure it seals all the way
around the air cleaner canister, then tighten the
ES
clamps. Figure 4-11
4. Check all fittings and clamps periodically for tightness
and inspect hoses for holes or cracks.
5. Periodically check the intake hose for signs of
ingested dust. Locate and repair the source of
ingested dirt.
FR
6. Never operate the machine without an air filter
installed.
Overservicing
Overservicing occurs when an air filter element is removed
IT
for cleaning or replacement before it is necessary. Each time
the filter is removed a small amount of dirt and dust could
fall in the intake system. This accumulated dirt can cause a
dusted engine. It only takes a few grams of ingested dirt over
the normal service life of an engine to cause a dusted engine.
Do not clean the element, but replace with a new element
NL
only. Cleaning used air filter elements, through improper
cleaning procedures, can get dust on the inside of the filter
causing dirt ingestion and engine failure.
It is important to note that whenever an air filter element is
cleaned by any method, the person or company performing
PT
the cleaning assumes responsibility for the integrity of the
filter from then on. The warranty for air filters expires upon
cleaning or servicing in any manner because the condition of
the filter after servicing is completely out of the filter
manufacturer's control. Therefore, on a dust ingested engine
failure, there will be no warranty consideration if the air filter
SV
element has been cleaned or serviced in any manner.
REV A
A
Figure 4-12
A partially dirty air filter element works better than a new
element. Therefore, a dirty filter element is not bad for the
engine unless it is excessively restricting the air flow and
engine performance is affected. The reason is simple. The
media in the filter must be porous to allow air to pass
through it. When dirty air passes through the filter, the dirt
plugs some of the holes in the media and actually acts as
part of the filter media. When the next round of dirt enters,
the first dirt helps filter out even smaller particles making the
filter more efficient at stopping dirt from entering the engine.
This is referred to as barrier filtration.
Of course, at some point the filter media becomes too
clogged to allow air to pass.
The mowing conditions will determine the frequency of air
filter element changing.

General Engine Maintenance

Detailed instructions and recommendations for break-in
and regular maintenance are specified in the Engine Owner's
Manual. Please refer to this manual for engine servicing,
lubricating oil levels
recommendations, bolt torques, etc. The engine warranty is
backed by the engine manufacturer. Special attention should
be paid to applicable data which will not be duplicated here.

Belts

Inspect belts frequently for wear and serviceability.
Replace a belt that shows signs of:
• severe cuts
• tears
• separation
• weather checking
• cracking
• burns caused by slipping.
Slight raveling of belt covering does not indicate failure,
trim ravelings with a sharp knife.
If the pump belt fails, loss of steering control will
occur especially when operating on a slope. If you
lose steering control while operating the mower, turn
the engine off and, if on a slope, step off of the
operator's platform to the uphill side. Inspect the
machine and involve your Hustler
the problem before continuing to operate.
Inspect the belt pulley grooves and flanges for wear. A new
belt, or one in good condition, should never run against the
bottom of the groove. Replace the pulley when this is the
case, otherwise the belt will lose power and slip excessively.
Never pry a belt to get it on a pulley as this will cut or
damage the fibers of the belt covering.
Keep oil and grease away from belts, and never use belt
dressings. Any of these will destroy the belt composition in a
very short time.
4-6
with quality and viscosity
Dealer to resolve
®
606834CE