Parkside PZKS 1500 A1 Operating And Safety Instructions Manual page 24

– The generation of noise is influenced by various
factors, including the characteristics of saw
blades, condition of saw blade and electric
tool. Use saw blades which were designed for
reduced noise development, insofar as possible.
Maintain the electric tool and tool attachments
regularly and if necessary, initiate repairs in
order to reduce noise.
– Report faults on the electric tool, protective
devices or the tool attachment to the person
responsible for safety as soon as they are dis-
covered.
3 Safe work
- Make sure that a suitable saw blade for the mate-
rial to be cut is selected.
- Never use the machine to cut other materials as
specified.
- To transport the machine follow the procedure
of point 9.
When transporting the electric tool, only use the
transport devices. Never use the protective de-
vices for handling or transport.
- Operate the machine only if the protective devices
are functional, in good condition and in the correct
position.
- The floor around the machine must be level, clean
and free of loose particles, such as chips and cut-
ting residues.
- Only use saw blades for which the maximum
permissible speed is not lower than the maximum
spindle speed of the machine and which are suit-
able for the material to be cut.
- Be sure to only use spacers and spindle rings
specified by the manufacturer as suitable for the
intended purpose.
- Attention! Do not replace the laser by a different
type.
Repairs may only be carried out by the manufac-
turer or an authorized representative.
- Do not remove any cutting residues or other parts
of workpieces from the cutting zone while the ma-
chine is running and the saw unit is not at rest.
Instructions for proper and safe sawing:
a) Clamp the workpiece always at the saw table
firmly. Therefore please use the supplied clamping
device.
b) Make sure that the machine is secured before
each sawing;
c) If necessary attach the machine to a workbench
or the like.
Fasten the machine to the workbench, using the
holes at the fixed saw table.
d) Support long workpieces (e.g. with a roller table)
to prevent them sagging at the end of a cut.
e) Make sure that the saw blade does not touch
the rotary table in any position by pulling out the
mains plug and rotating the saw blade by hand in
the 45° and 90° position. If necessary, readjust the
saw head.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair active
or passive medical implants under certain conditions. In
order to prevent the risk of serious or deadly injuries, we
recommend that persons with medical implants consult
with their physician and the manufacturer of the medical
implant prior to operating the electric tool.
SAFETY INSTRUCTIONS FOR THE HANDLING OF
SAW BLADES
Only use insertion tools if you have mastered their use.
1
Observe the maximum speed. The maximum
2
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
3 Observe the motor / saw blade direction of rotation.
Do not use any insertion tools with cracks. Sort out
4
cracked insertion tools. Repairs are not permitted.
Clean grease, oil and water off of the clamping
5
surfaces.
6 Do not use any loose reducing rings or bushes for
the reducing of holes on saw blades.
Make sure that fixed reducer rings for securing the
7
insertion tool have the same diameter and have at
least 1/3 of the cutting diameter.
Make sure that fixed reducer rings are parallel to
8
each other.
9 Handle insertion tool with caution. They are ideally
stored in the originally package or special contain-
ers. Wear protective gloves in order to improve
grip and to further reduce the risk of injury.
10 Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
11 Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
12 Only use the supplied saw blade for cutting wood,
never for the processing of metals.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
0
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unpro-
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure
to the beam can occur.
• If the mitre saw is not used for an extended period
of time, the batteries should be removed.
GB/IE 19