Recommended Hookup - Campbell Hausfeld IronForce IFN2190 Operating Instructions Manual

Manual de Instrucciones
seguridad y la duración pueden verse
Unidos continentales, comuníquese con
nosotros al 1-513-3678-1182. reducidos. Cuando ordene partes de
repuesto o sujetadores, especifique el
Clavos et Repuestos
número de la parte.
Use solamente sujetadores Campbell
Para reparar la clavadora
Hausfeld originales (o su equivalente) -
Las reparaciones de la clavadora las
(vea la información sobre intercambio
debe hacer SOLAMENTE un técnico
de sujetadores). Use solamente partes
calificado que tenga experiencia.
de repuesto Campbell Hausfeld
originales. Nunca substituya las partes.
Para colocarle los sellos
No use partes modificadas o partes
Cada vez que repare una clavadora
que no den un rendimiento
deberá limpiarle y lubricarle las partes
equivalente al equipo original. El
internas. Le recomendamos que use
rendimiento de las herramientas, la
Sujetadores
La herramienta IFN2190 también coloca sujetadores diseñados para: Sears 18465, Porter Cable FR350, Hitachi NR83A, y Senco
FramePro 702XP, 752XP, Ridgid R350RHA y DeWalt D51844, D51845.
La herramienta IFN3490 también coloca sujetadores diseñados para: Porter Cable FC 350A, Hitachi NR83AA2, Senco FramePro
701XP, 751XP , Ridgid R350CHA, DeWalt D51822, D51823 y Paslode F-3505.
Modelo IFN3490 and IFN2190
Parker O-lube o un lubricante
equivalente en todos los anillos en O. A
cada anillo en O se le debe dar un baño
de lubricante para anillos antes de
instalarlos. Igualmente, deberá ponerle
un poco de aceite a todas las piezas
que se mueven y muñones. Finalmente,
después de haberla ensamblado y antes
de probar la herramienta deberá
ponerle unas cuantas gotas de aceite
sin detergente 30W u otro aceite
similar, en las líneas de aire.
www.chpower.com
6-Sp
Operating Instructions
compressor manufacturer for

RECOMMENDED HOOKUP

information.
1. The air
Operating The Nailer
compressor
Read this manual and understand must be able
all safety warnings and instructions to maintain a
before operating the nailer.
minimum of 70
psi when the nailer is being used.
LUBRICATION
An inadequate air supply can cause
This nailer requires lubrication before
a loss of power and inconsistent
using the nailer for the first time and
driving.
before each use. If an inline oiler is
2. An oiler can be
used, manual lubrication through the
used to provide oil
air inlet is not required on a daily basis.
circulation through
The work surface
NOTICE
the nailer. A filter
can become
can be used to
damaged by excessive lubrication. Proper
remove liquid and
lubrication is the owner's responsibil- ity.
solid impurities which can rust or
Failure to lubricate the nailer properly
"gum up" internal parts of the
will dramatically shorten the life of the
nailer.
nailer and void your warranty.
3. Use 3/8" air
1. Disconnect
hoses with a
the air
minimum
supply from
working
the nailer to
pressure of 150 psi. Use 1/2" air
add
hoses for 50' run or longer. For
lubricant.
better performance, install a 3/8"
2. Turn the nailer
quick plug (1/4" NPT threads) with
so the air inlet
an inside diameter of .315" (8mm)
OIL
is facing up.
on the nailer and a 3/8" quick
Place 4-5 drops
coupler on the air hose.
of 30 W non-
4. Use a pressure regulator on the
detergent oil
compressor, with an operating
into air inlet.
pressure of 0 - 125 psi. A pressure
Do not use
regulator is required to control the
detergent oils, oil additives, or air
operating pressure of the nailer
tool oils. Air tool oils contain
between 70 and 120 psi.
solvents which will damage the
NO-MAR DECKING TIP
nailer's internal components.
The no-mar decking tip is designed to
3. After adding oil,
eliminate marks caused by the serrated
run nailer briefly.
work contact element (WCE). The no-
Wipe off any mar tip may be removed if not
required (See REMOVING NO-MAR
excess oil from
DECKING TIP). Use tool in single cycle
the cap exhaust.
mode (SEE OPERATIONAL MODES)
when no-mar tip is in place.
Recommended Hookup
Quick Quick
Plug Coupler
Model IFN3490 and IFN2190
REMOVING NO-MAR DECKING TIP
1. Disconnect air
70 psi
supply from
Min.
nailer.
120 psi
Max.
2. Remove all fasteners from magazine
(See UNLOADING THE
NAILER).
3. Remove no-mar tip retaining ring.
Retaining
Ring
4. Pry no-
No-
mar tip
Mar
away
Tip
from the
work
contact
element.
5. Replace
retaining
ring onto
no-mar
tip, then
store tip
in safe
place for future use.
INSTALLING NO-MAR DECKING TIP
1. Disconnect air
supply from
nailer.
2. Remove all fasteners from magazine
(See UNLOADING THE NAILER).
3. Remove retaining ring from no-mar
tip.
Regulator
Quick Plug
(Optional)
Oiler
Quick
Coupler
(Optional)
Air
Hose
Filter
3
No-Mar Tip
Work
Contact
Element